Search Documents

By S. A. Bogidaev, M. Yu. Tiunov

"The paper describes the results of the flotation tests with complex rare metal ores from deposits in the Trans-Baikal Territory. Correlations between the quality of produced wolframite, hubnerite and mica concentrates with or without the presence of various alkaline modifiers are determined. Commonly, rare metal ores contain minerals of comparable value to main elements recovered in processing plants using gravitational methods. The paper describes the results of flotation recovery of valuable minerals – main and associated – from gravity tailings of deposits in the Trans-Baikal Territory. It was found that gravity tailings from the first deposit contained fine-grained wolframite, mica (muscovite, lepidolite etc.), feldspar; hubnerite, scheelite, beryl, fluorite, rubidium-containing muscovite from the second deposit, correspondingly. This paper presents the results of the stage flotation tests with the production of tungsten (wolframite, hubnerite), fluorite and mica concentrates from gravity tailings. Figure 1 demonstrates the flowsheet of tungsten ore minerals and mica stage flotation from gravity tailings of the first deposit.Wolframite can be floated using oleic acid with the presence of soda ash, a complexing collector (IM-50), under slightly alkaline conditions in combination with a nonpolar collector [1, 2, 3, 4]. The study included wolframite flotation using the combination of two alkaline modifiers. Flotation of wolframite was performed after pulp desliming, using tall oil saponified with soda ash. The recovery of wolframite in the concentrate of rougher flotation reached 80-85%; the concentrate contained up to 1% of tungsten oxide that can be upgraded to a saleable product using gravitational methods. This procedure was tested during flotation of wolframite, tantalite-columbite and pyrochlore, and provided high performance regardless of a season, at pulp temperatures of 8-10°C, though fattyacid collectors are significantly inefficient at such low temperatures due to low solubility, dispersion and increased collector consumption, consequently. The introduction of two alkaline modifiers in pulp appears to improve these characteristics.The first stage of the tests was focused on increase of iron-bearing tungsten ore minerals recovery from gravity tailings and stabilization of the cold pulp flotation process."

Jan 1, 2018

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By P. Thareja, V. Prasad, S. P. Mehrotra

In recent times, the transportation of minerals and their tailings has become a major concern across the world. There exists a huge demand of efficient and cost effective transportation system which poses minimum environmental damage. One of the economically and environmentally viable techniques which potentially offer a solution to the above problem includes transportation of minerals and their tailings in the slurry form through pipelines. Slurry transportation through pipelines is reported to be more beneficial in terms of cost, environmental impact, maintenance and safety when compared with other conventional modes of bulk transportation such as train, truck, barge and conveyors. The main challange associated with hydraulic transportation of slurries is to obtain a non-settled slurry and to design a pipeline system which results in the optimum energy requirement for transporting a large throughput to longer distances at a lower cost. The feasibility of hydraulic transportation of slurries through pipes mainly depends upon slurry properties and flow conditions in the pipe. Results from rheological studies exhibit the presence of shear thinning flow behaviour of minerals and their tailings in water. The flow behaviour index (n) and consistency coefficient (k) obtained from the rheological analysis are further used for the specific energy consumption and energy losses during transportation. The cost of transportation in USD per ton per 100 km and transport capacity in tons per day are calculated from the specific energy consumption to transport these slurries. The results demonstrate that the slurries can be transported to long distances (say, 100 km or more) corresponding to optimum energy consumption and dissipation rate at a substantially cheaper cost than the existing rail and road transport in India. Although we have carried out transportation studies with coal fly ash (CFA), lignite & bauxite slurries, for paucity of space, the results reported here are essentially for CFA slurries. Details of our investigations with lignite coal & bauxite will be reported seperately.

Jan 1, 2018

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By E. Hulthén

Crushing plants are widely used around the world as a pre-processing step in the mineral and mining industries and as standalone processing plants in the aggregates industry. Despite automation and different advanced model predictive control, a lot of the process is still managed by operators. The operators affect a lot of the performance. The numbers of the improvement they can achieve are at least as big as the advanced control algorithms?, today. Therefore, it is also important to train the operators so they know how to behave in different situations. Models for crushers and other production units have been developed during the years and the latest add is the different units? dynamic behavior being brought in, which gives the crushing plants dynamic time dependant performance. This can be used as a simulator for operators training. By connecting a Human Machine Interface (HMI) to a dynamic simulator with the models incorporated, a training environment for operators can be achieved. In this paper, a dynamic crushing plant simulator implemented in MATLAB/SIMULINK has been connected to an HMI via a PLC. The HMI is placed in a control room at the university and complemented with monitors showing sequences from the process connected to the simulations, thus creating a realistic control room for training. In the created training environment, the operators can be trained under realistic conditions. Simple training scenarios and how they could be simulated are discussed. Apart from the increased level of knowledge and experience among the operators, the time is an important factor. While a real crushing plant is still being built, the operators to be can already be trained, saving a lot of the commissioning time. Keywords: crushing, cone crusher, simulator, control room, operator, training

Sep 1, 2012

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018

Dielectrophoresis is a separation technique that uses a non-uniform electrical field to separate particles on the basis of their permittivity. There are many areas of mineral processing that might benefit from the application of dielectrophoresis. These include: coarse removal of gangue, recovery of ultrafine particles, upgrading of flotation concentrates or simply as a laboratory analysis technique. In order to determine the potential value of dielectrophoresis to the mineral processing industry, the response of composite particles was investigated. The electrical properties of composites involve complex relationships between the shape, distribution and permittivity of the individual grains within the rock. The relationship between mineral composition and dielectrophoretic force was measured on single particles from two ore types. The results were used to populate a model that could predict the separation characteristics of the ore. The insights gained from this model separator allowed potential applications of the technology to be examined and their performance evaluated.

Sep 1, 2012

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By B. Rath

An effective process plan is an important part of maintaining consistent recoveries in mineral processing operations. Traditionally, Mineralogical studies are completed using chemical and metallurgical methods to monitor recovery and elemental distribution. The development of mineralogy and more efficient processes in mineral analysis techniques means that mineralogy is now more accessible as an efficient and comprehensive study tool. As operating costs increase and feed grades decrease it is important to maintain tight control of process and ensured maximum recovery is maintained at all times. Just a few days of losses in recovery caused by changes in ore type or processing conditions can have a large effect on total metal recovery and profit. Mineralogical audits can be used to minimize these losses by monitoring the fundamental behavior of feed ore on a regular basis. Smart use of mineralogical studies can develop mineralogical and ore type benchmarks in a detailed, which can be used in process control and monitoring. Geological ore types can be used to identify key mineralogical parameters that may be used in routine and cost effective analysis. Mineralogical systems ideally suited to this because of the depth of information on everything from modal mineralogy to locking/liberation characteristics and mineral associations. Mineralogical studies can equally be applied to specific unit operations within the process, which can allow more detailed information to be gathered on areas of the process that have been identified as critical. This will be especially effective for flotation or oxidation processes where process parameters can be very sensitive to small changes in mineralogy. This paper deals with the Ore Morphology, Ore Mineralogy, Gangue mineralogy, Photo micrographs under reflected, transmitted light and XRD studies Ore, Mineral studies of Sub grade Iron ore of Bacheli Complex, Bailadila Sector, India. Keywords: mineralogy, liberation, liberation studies, ore mineral, gangue mineral, morphology, jasper, ferruginous clay

Sep 1, 2012

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014