Search Documents

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By Venugopal B, M Kumaran, Thomas John, Vetriselvan A

The initial pile load tests are conducted to ensure the geotechnical capacity of the pile in a particular site condition. Normally kentledge method is adopted for the compression pile load tests. In this method the entire kentledge load is loaded above secondary beams which are supported by concrete blocks above the Natural Ground Level. So, it is important to ensure the SBC (for shear and settlement) of the natural ground. In one of our projects initially it was decided to go with kentledge system for initial compression load test on 56m long 1200mm diameter BCIS pile. The test load and total kentledge load were 2160t and 2700t, respectively. The soil strata mainly consisted of clay with low SPT N value and water table almost at ground level. It was suggested to replace top soil using Granular Sub-base (GSB) with good compaction in order to avoid excessive settlement of concrete blocks placed to support the kentledge weight. When the kentledge loading started, even before reaching 10% of total kentledge load, excessive settlement on the GSB layer was observed. This paper describes the problems faced during normal kentledge method and how it was overcome using the liner pile system for initial compression load tests in this particular site condition for higher test load.

Nov 1, 2022

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

By Marwa Nabil, Alaa A. Ata

"Recent developments in the analysis of piled rafts has incorporated the load sharing of the raft and the piles to support the superstructure. In the piled-raft system, piles are cast monolithically with the raft and the load is partly transmitted by the raft to the soil directly below it, and partly by the piles to more competent deep soil. While these piles are effective in increasing the bearing capacity and reducing the settlements, they often lead to significant straining actions at the pile head-raft connection which may constitute the weakest link. An attempt to provide a more economical solution, that at the same time overcomes this weak link, is to disconnect the pile heads from the raft and introduce an intermediate cushion of compacted fill. In this case, the piles are considered as reinforcement to the subsoil and will also act as settlement reducers. This paper investigates the load transfers mechanism of the unconnected piled raft with cushion using ABAQUS finite elements Program. The main objective is to provide an in depth analysis of the raft–soil–pile interactions in multi-layered soil under static and seismic loads. The investigated system provides an economical alternative for traditional connected piled raft foundation, where there is no need to reinforce the piles, no need for pile head demolition or expensive waterproofing of the pile head connection. Cost analyses of unconnected versus connected piled raft systems confirmed a cost savings in the construction that may reach from 50 to 70 percent.INTRODUCTIONDesigners around the world have gained more confidence to use the piled-raft as a more realistic system where the raft and the piles share transferring the superstructure loads to shallow and deep soil layers. A further advancement is to use unconnected piled rafts as another practical and economical alternative to the traditional piled rafts. Unconnected piled raft is also synonymous to settlement reducing piles; or simply, soil improvement piles. Liang et al. (2003) has extended the concept of pile-raft-foundation to a new type of foundation called composite piled raft foundation or unconnected piled raft foundation. The foundation is composed of a sand/gravel cushion sandwiched between the raft and piles. The piles group may contain short and long piles. The short piles are constructed of flexible materials such as soil-cement columns or sand-gravel columns, and are used mainly to improve the bearing capacity of shallow soft soil; the long piles, which are made of relatively rigid materials such as concrete, and their main function is to reduce settlements. The cushion plays an important role in mobilizing the bearing capacity of the subsoil and in modifying the load transfer mechanism of the piles. In Shanghai, China, this system of unconnected piled raft has proved to be quite suitable and effective in coastal areas, where deep soft soil deposits exist."

Jan 1, 2016

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Yazen Khasawneh, Osvaldo P. M. Vitali, John E. Agee, Mohammad Nassim

A 3D FEM modeling of a ground improvement solution for an ice rink slab with stringent differential settlement limits is presented. Due to the complexity of the geotechnical conditions and strict deformation requirements, a structural slab supported by micropiles was initially proposed. However, this solution was costly and alternative solutions using ground improvement techniques were investigated. The proposed slab is supported directly on rock at one end and on approximately 45-ft deep cohesive soils on the other end. The numerical simulations show that differential settlement would be larger than allowable, if the ice rink slab is supported directly on the existing subgrade. The addition of the ground improvement scheme with compaction grouting demonstrated that the anticipated differential settlements are reduced significantly and would become less than the allowable magnitude. This study demonstrates that the use of numerical simulations to study complex loading and geological conditions will help to optimize designs and may result on significant cost savings.

Sep 8, 2021

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By N. V. Nayak

Konkan Railway Project is one of the most ambitious railway construction projects in India, involving construction of a 760.km long, Broad Gauge (1676 mm), single track railway line, connecting Roha in Maharashtra State with Mangalore in Kamataka State. The railway line travels along the Western Coast of Indian subcontinent, through states of Maharashtra (382 km), Goa (105 km) and Karnataka (273 km) (Fig.1). The project alignment traverses through one of the most formidable terrains ever encountered, in the history of railway construction in India. In the State of Goa only, railway alignment is crossing 6 major rivers Terekhol, Chapora, Mandovi, Zuari, Sal and Talpona. Zuari Railway Bridge (1305.6 m), Mandovi Railway Bridges (I and II) (1182.7 m) rank as 2nd and 3rd long bridges, (first longest bridge being Sharavati Bridge (2.2 km} at Honavar) which have been constructed on Konkan Railway. All these three bridges have been constructed by M/s.Asia Foundations and Constructions Ltd. (AFCONS). This paper presents, case history of construction of pile/caisson foundations for Zuari and Mandovi Bridges.

Jan 1, 1996

By Ross T. McGillivray, David S. Graham, Dan A. Brown, Steven D. Dapp

"The Selmon Expressway includes an elevated structure extending across several miles of weathered karstic limestone geology, and represents a challenge for design because of the high variability of the material and the difficulty in characterizing the strength. The nature of the epikarst in this region of Tampa is such that variability can be extreme within distances of only a few feet. The weathered rock includes extremely soft soil infill within solution features on and within the formation. The limestone is so weathered that coring typically does not yield useful samples for strength testing, and in-situ Standard Penetration Testing (SPT) tests often encounter refusal blow counts. Thus the challenge for foundation design includes two components of reliability risks: the uncertainty associated with the ground conditions at a given foundation location plus the uncertainty associated with the foundation performance at a given location even when the stratigraphy is determined.This paper describes the design approach that has been implemented successfully for two projects at the Lee Roy Selmon Crosstown Expressway (LRS) in Tampa, Florida: the assessment and remediation of the reversible elevated lane (REL) foundations constructed in 2004, and the elevated expressways widening project constructed in 2012. Included in this design approach is a method developed for computing axial resistance in this local geology. Design for axial loading relies primarily on the development of side resistance, which was considered less subject to performance risks than base resistance. The calculation method incorporates a statistical analysis of SPT data, tempered by engineering judgment, to characterize stratigraphy at a given location into either soil, intermediate geomaterial (IGM) or rock.IntroductionThe subsurface stratigraphy of sites underlain by weathered limestone formations can be highly variable with respect to material layer thicknesses and strengths, even over short horizontal distances. This is the case for much of Florida, and particularly the Tampa area. These conditions present a challenging environment for the design of drilled foundations because of the need for a reliable determination of subsurface conditions at each foundation location, as they relate to the expected axial performance. Contributing factors include:"

Jan 1, 2015