Search Documents

By Sanjeev Malhotra

"This paper presents the results of a pile installation monitoring and performance assessment program for pile foundations supporting 14 piers and 2 abutments of the 1700-ft long bridge crossing over a river in Baltimore, Maryland. Dynamic measurements were conducted during installation and restrike of 16 test piles, one at each support location. The foundation piles were 30-inch diameter, 0.75 inch thick pipe piles at the piers and 24-inch diameter, 0.5 inch thick at the abutments. The piles at the piers were approximately 100 ft long and were designed to carry 260 kips service load with a factor of safety of 2.25. The piles were driven open ended into a variable site stratigraphy containing recent deposits of organic clayey silts near the mudline followed by loose to medium dense sand, with some silt, and then by soil deposits from the Cretaceous period consisting primarily of dense to very dense, poorly to well graded sands and gravels and cobbles, with occasional seams of very hard to very stiff, low to moderate plasticity silts and clays. This paper presents the approach taken to evaluate the driven index piles and to develop criteria for driving production piles. It provides the Engineer with some data on pile driveability in Cretaceous soils in the Baltimore area, soil set-up effect, and an estimate of pile capacity.INTRODUCTIONThe typical approach to pile foundation design and construction should include an indicator pile program with dynamic measurements and a static load test program. However very often paucity of funds and schedule constraints cause an owner to do away with conventional static load testing which can take $25,000 to $100,000 and several weeks per test. This paper examines an alternate (though not equivalent) truncated approach to foundation assessment and presents a case history where this approach was implemented.Dynamic measurements were conducted during pile installation for the 14 piers and 2 abutments of the new 1700-ft long bridge over a river in Baltimore, Maryland. Strain transducers and accelerometers were attached to the pile top during initial driving and restrike of 16 pipe piles. The foundation piles consisted of 30-inch outside diameter, 0.75-inch thick pipe piles at the piers and 24-inch outside diameter, 0.5 inch thick at the abutments. The piles were driven open ended into a variable site stratigraphy. The approach taken to assess the foundation performance included 1) a pre-field wave equation driveability analyses, 2) field pile driving measurements, 3) post-field Case Pile Wave Equation Analyses (CAPWAP), and, 4) revised wave equation analyses based on field and CAPWAP data. The following sections describe in greater detail each of the steps taken to assess foundation performance and the results obtained."

Jan 1, 2005

By Karl A. Higgins, Michael D. Venezia

The South Capitol Street Corridor Project is one of the District Department of Transportation’s (DDOT) largest projects, and is currently under construction. This case study will focus on the design of the foundation piles for the main spans of the iconic Frederick Douglass Memorial (FDM) Bridge, and will include a discussion of the foundation design evolution from an originally designed alternative foundation system (i.e. coffer dams and drilled shafts), to the current use of driven Large Diameter Open End Pipe (LDOEP) Piles. The paper will provide a discussion of the design methodology used during preliminary engineering and final design, and will highlight insight gained from the extensive load testing program completed to date. The load testing program consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre-production test piles. Specifically, data gathered during the nearly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles. This paper will also discuss limitations of currently accepted industry design methods for predicting the capacity of LDOEP piles, a subject that is also currently being researched by FHWA. The data from this test pile program will help design assumptions for future projects. INTRODUCTION The Frederick Douglass Memorial (FDM) Bridge carries South Capitol Street across the Anacostia River in Southeast/Southwest, Washington, DC, and is owned and maintained by the District Department of Transportation (DDOT). The existing FDM Bridge is nearly 70 years old, serves as a major artery into the city, and has been classified as functionally obsolete. As a result of the condition, age and limitations of the existing bridge structure, DDOT deemed it necessary for complete replacement of the bridge. The replacement project consists of the construction of a new bridge traversing the Anacostia River, as well as the reconfiguration of the Suitland Parkway and I-295 interchanges located at the eastern terminus of the FDM Bridge. Final design and construction services for the replacement project were procured by DDOT through a Design-Build contract. This paper will focus on the driven Large Diameter Open End Pipe (LDOEP) Piles used for support of the main span of the new FDM Bridge which is currently under construction. Discussion regarding the LDOEP Pile design methodology has been included, along with commentary regarding currently available industry guidance related to design and construction of LDOEP Piles. Much insight has been gained during the mostly-completed and extensive load testing program which consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre- production test piles. Specifically, data gathered during the mostly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles.

Jan 1, 2019

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

Jan 1, 1989

By Reda Mikhail, M. Birkan Bayrak

The Washington State Department of Transportation (WSDOT) State Route (SR) 167/70th Avenue East Vicinity Bridge Replacement Design-Build project is located in Fife, Washington. This $40 million project consists of replacing the existing 70th Avenue Bridge over Interstate 5 (I-5) with a single-span bridge of about 220 feet long with approach embankments. The subsurface conditions along the new bridge alignment generally consists of alluvial deposits with high potential of liquefaction overlying glacially overridden deposits. In the early stages of the project, drilled shafts were considered as the deep foundation system; however, after an additional subsurface investigation is completed at the site, driven pipe piles were selected as the deep foundation system. Bridge abutments are supported by 24-inch diameter, 80-foot-long open-end driven steel pipe piles. The pile length was determined to bypass a relatively thick liquefiable zone and to tip the piles above what could be compressible soils. The use of advanced seismic analysis was instrumental in optimizing the pile length. The dynamic testing performed on numerous piles indicated what could be unique soil setup factors compared to those measured in local projects as well as those reported in national design manuals. Detailed discussions of the pile foundations design and construction is presented in this paper.

Sep 8, 2021

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Brian J. Olson, Kevin Haiar

Originally constructed between 1939 and 1941 as part of Franklin D. Roosevelt’s New Deal programs, the Bonneville to Hood River 115 kV Transmission Line required an infrastructure upgrade to remain reliable and in-service. The line traverses the rugged landscape of the Columbia River Gorge on the Oregon- Washington border, featuring steep, talus slopes; uneven, rocky terrain; and a variety of environmental sensitivities. This paper details the design and construction of 27 micropile foundations for new, fire- hardening steel poles through a particularly challenging stretch of the alignment. The difficult access and environmental constraints at these sites designated them as helicopter-accessible and precluded the collection of detailed geotechnical information prior to construction. Micropiles provided a viable foundation alternative due to their portability and flexibility during construction. Detail will be provided on the extensive preliminary desktop study performed, as well as the process of developing engineering designs to successfully accommodate for variability and unknowns in complex geological conditions. With an increasing number of electric power projects traversing challenging terrain and facing similar obstacles, this project stands to provide valuable lessons learned to the industry.

Sep 8, 2021

By Gang Guo, Zhong Liu

"In response to an increasing demand of anchored structures for underground space and transportation infrastructure in China, an innovative underreamed ground anchorage system was created. The novel anchorage system has provided more efficient functions with higher capacity at lower cost, because of the enlarged cylindrical body (known as ECB) sealed in capsule at bottom of anchorage. This paper presents the detailed structure of innovative anchorage system and its special features. To investigate the bearing mechanism of new anchorage, we evaluate its performance and failure mode based on the experimental results, and also indicate its strain-hardening load-displacement relationship. Unlike the shaft anchorages, it is identified no overall failure to be found in soil surrounding the underreamed anchorage. More importantly, the anchorage capacity is governed by the base resistance, which takes more than 80% of total pullout capacity resulting from the contribution of ECB. Finally a case history of anti-floating project introduces the new combined construction approach and procedure, which has provided the contribution to the quality control and cost efficiency.INTRODUCTION AND BACKGROUNDThe construction boom over two decades in China has resulted in an increasing demand for underground space and slope stability. The infrastructures market requires the more efficient anchorage systems for retaining structures, resisting uplift forces and slope protection. The major concern focuses on gaining higher capacity and lower cost resulted from perfecting anchorage systems. There are three main anchorage systems designed to achieve the above objectives: ? single bore multiple anchorage system (Barley 1997), ? regroutable anchorage system (Smoltczyk 1991), ? underreamed anchorage systems (Xanthakos 1991). Generally, the concept ? comparing with the other two, can be more competitive due to its distinct advantages. To improve the performance and durability of ground anchorages under the complex geological conditions and diversified engineering requirements, a number of different underreamed anchorage technologies had been used, which included cone - shape anchorage described by Liao, Wu and Shu (1997) in Taiwan, Soilex anchorage developed in Sweden (Massarsch et al. 1997), Soletanche anchorage proposed in France, blasting anchorage used in Czechoslovakia (Hobst and Zajic 1986), jet-grouting anchorage innovated in Europe (Anon 1988), as well as deep mixing anchorage created in Japan (Cheng et al. 2000).The underreamed anchorage systems have the remarkable advantages compared to the shaft anchorage system. However, there are also some weaknesses inherent in the underreamed systems. For instance, the mechanical underreamed anchorage is unsuitable in sand or waterbearing ground, because the enlarged hole is easy to collapse, and it is hard to ensure the quality of anchorages. On the other hand, relying on the blasting in deep hole, the geometrical space and dimension of enlarged hole is uncontrollable, meanwhile, the continuous blasting operations may easily cause the serious ground deformation and the negative effects to the completed anchorages."

Jan 1, 1900

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By Lisa R. Papandrea, David Chen, Walter E. Kaeck

"Construction of the University at Buffalo’s new School of Medicine and Biomedical Sciences (UB-SMBS) required excavation in variable ground to a depth of more than 40 ft adjacent to the NFTA Metro subway and Allen Street Station. Complicating the building design and construction, the new medical facility incorporates the at grade Station entrance building, requiring a combination of temporary and permanent excavation support structures, a complex sequence of ground support installation, and a mix of shallow and deep foundations to accommodate the large floor spans and concentrated column loads introduced by building over and adjacent to the Station entrance. Excavation and foundation construction was challenged by a stratified soil profile with interlayered and sensitive sands, silts and clays and complicated groundwater regime with perched and regional water tables. Efficient construction required ongoing coordination between the design team and contractor, careful field observation, and construction monitoring in several facets of below grade construction. This paper describes the design and construction of excavation support structures and foundations to manage the variable ground, congested site conditions, and complications of building adjacent and above an active subway station. Use of site instrumentation and monitoring data to provide guidance in construction when unanticipated field conditions arise is illustrated. Lessons learned in installation and sequencing of excavation support, groundwater control and foundation construction are also discussed.INTRODUCTIONUniversity at Buffalo President Satish K. Tripathi heralded the new School of Medicine and Biomedical Sciences (UB-SMBS) as a future linchpin of UB’s downtown campus that will revitalize the area and enhance western New York’s emerging bio-sciences corridor. The $375 Million, 628,000 square foot, eight story building with two basements is expected to house 2,000 faculty, student and staff allowing UB to increase class size from 140 to 180 students. It will be constructed above the Niagara Frontier Transportation Authority’s (NFTA) Allen Street Station, creating a direct connection to Buffalo’s light rail system. The 200 ft x 400 ft site is bounded by Main Street, High Street, Washington Street and the Roosevelt Apartments and adjoining parking lot at the west, north, east and south respectively, as shown in Figure 2. Groundbreaking for the new building was in October 2013 with the facility scheduled to open in early 2017."

Jan 1, 2016

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900