Search Documents

By Y. Guglielmi, C. Gout, P. Henry, P. Dick, C. Nussbaum

For a decade, observations and experiments conducted in underground environments worldwide (mines, underground research laboratories - URL) made it possible to bridge the scale gap between laboratory scale and large scale faults. Indeed, underground rock laboratories allow developing decameter scale relatively well constrained experiments at the smallest distance from the hypocenters. URL’s experiments allowed developing new monitoring technologies coupling pressure-strain-seismic measurements and reproducing complete earthquakes sequences analogous to natural ones. They also allowed exploring past movements of faults and sometimes also paleofluids in three dimensions and characterizing different fault architectures and hydromechanical properties in unaltered conditions. This is particularly important in the study of faults affecting clay formations which could not be observed at the Earth’s surface because of the high alteration. Here we show how examples from the Mont Terri (Switzerland) and Tournemire (France) The URLs may help in (i) defining the concepts of fault architecture in shales, (ii) estimating fault hydromechanical properties from field decameter scale experiments. Some key results are that faults which are critically stressed or at the rupture limit can reactivate for stresses variations within the range of those produced by shallow underground excavations, and that slight micrometer-to-millimeter scale reactivations may lead to large factor-of-10-to-1000 permeability increases. Such promising results show that URL’s experiments may bring new insights on some key processes that control the relations between fault stability and permeability evolutions in very permeable layers.

Jan 1, 2015

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By G. Issid, J. McGinty, C. Lee, Y. Pepin

For more than a decade, Hatch has used process and logistics models to assist Rio Tinto Fer et Titane (RTFT) with capacity planning, debottlenecking, and optimization to help ensure design capability, capital effectiveness, and operational efficiency of the integrated production chain. Process models are used to optimize the physics-based aspects of the system, such as mass and energy balances, flow rates, yields, and equipment specifications. Dynamic logistics models are used to optimize how the various plant areas work together to achieve the desired ends and deal with such things as plant scheduling and synchronization strategies, sizing of buffers between processes, defining the required number of process and material handling units, and designing a plant layout that minimizes plant interferences and inefficiencies. The combined use of process models and logistics models enables the overall plant to be optimized from both a productivity and quality point of view, with each plant area working in harmony with one another to achieve targeted capacities and efficiencies. This paper describes the many benefits derived from such modeling efforts over the past 15 years for each of the major plant areas at RTFT: Beneficiation Plant, Smelter Plant, Steel Plant, UGS Plant, and Powder Plant (RTMP).

Jan 1, 2011

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By Georges Houlachi, Akram Alfantazi, Michael Mahon, Maysam Mohammadi

Corrosion resistance of the lead-based anodes directly influences the purity of the final product in the zinc electrowinning process. The anodic MnO2 layer that is electrodeposited on the anodes during this process can protect the anodes against corrosion. Sand-blasted anodes generate a uniform, adherent and shiny MnO2 layer, which gradually blisters and eventually sloughs off after several weeks. In this study, we attempted to develop a new method to stabilize the MnO2 protective layer on the anodes during the electrowinning process by providing suitable nucleation sites for electrodeposition of this layer. MnO2 particles (P80=40µm) were used as seed material for this purpose. Different techniques of galvanostatic and cyclic voltammetry polarizations, scanning electron microscopy (SEM) and atomic absorption spectroscopy (AAS) were employed to investigate the performances of the MnO2-seeded lead anodes. The experimental results showed that growth of the MnO2 layer is influenced by the MnO2 seed particles on the anode surface. The MnO2 layers electrodeposited on the MnO2-seeded lead anodes were uniform and strongly adherent to the substrate. This layer was more stable than those formed on the PbAg anode without MnO2 seeding. This could provide the anode with a higher level of corrosion protection. Moreover, formation of undesirable MnO2 mud in the electrolyte and the rate of manganese consumption were decreased when the MnO2-seeded lead anodes were polarized. These observations could be attributed to the different properties of the electrodeposited MnO2 layer on this anode in comparison with that formed on the PbAg anode.

Jan 1, 2016

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

World copper electrowinning tankhouse plant practices have been surveyed. This survey is a supplement to previous surveys that have been carried out in 1995, 1999, 2001, 2002 and 2003. On a world basis, process technology trends include the further installation of automated electrode handling systems including permanent cathode systems, automated cathode handling machines, fully automatic cranes and polymer concrete cells. Designs also have included larger electrode sizes and higher electrolyte flows and current densities. Overall these trends have further resulted in optimized tank house productivities and improved electrowon cathode purity. Most greenfield copper electrowinning projects are occurring in South America and Central Africa.

Jan 1, 2007

By M. Moats

World copper refining tankhouse practices have been surveyed. This survey is a supplement to previous surveys that have been carried out in the 1987, 1991, 1995, 1999, 2001 and 2003. On a world basis, process technology trends include the further installation of automated electrode handling systems including permanent cathode systems, automatic anode preparation and cathode handling machines, section switches, fully automatic cranes and polymer concrete cells. General plant process control has increased with more automation of material handling in the copper refining tankhouse. The general trend for most greenfield copper refining projects remains in eastern Asia.

Jan 1, 2007

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By Elaine Ellingham, Francis T. Manns

"The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at 0.156 oz/T Au. The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distributions, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By A. Kishimoto, Yoshida Honmachi, T. Uda, Y. Taninouchi

Recycling of e-scrap is often performed by utilizing a pyrometallurgical Cu smelting process. Several valuable metals, including precious metals, can be efficiently recovered through the Cu smelting process. However, recovery of Sn is quite difficult because it is distributed in slag during the smelting process. Sn is used as solder and plating in electronic devices, and its recycling will be more important in the future. In light of this background, a pretreatment process that can extract Sn directly and selectively from e-scrap was developed in this study. The proposed Sn extraction process involves alkaline leaching using iodate ions, IO 3, as an oxidizing agent. We conducted leaching experiments for Sn, Sn-Ag-Cu alloy solder, and Cu, and the effective dissolution of Sn was confirmed. In principle, the electrodeposition of Sn from the leach solution and regeneration of IO3 are possible by a subsequent electrolysis process. The results obtained in this study suggest that the proposed leaching process can be an effective and useful pretreatment for Cu-smelting-based e-scrap recycling. INTRODUCTION Electronic scrap (e-scrap), including waste printed circuit boards (PCBs), is one of the fastest growing waste treatment streams in the global urban environment. E-scrap contains numerous valuable metallic elements, including Cu, Sn, and precious metals, in rich quantity. Furthermore, some metals and other materials contained in e- scrap are hazardous to human health and the environment when they are not properly managed. The recycling of e- scrap is therefore a major concern in terms of resource supply and waste treatment, and it has been performed by many companies using a variety of methods.

Jan 1, 2019

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By Adrian White

Agenda Overview of pastefill at Kidd Mine Pipeline wear and the need to monitor Steel Loop monitoring Steel Borehole monitoring Monitoring pipe linings

May 1, 2013