Search Documents

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Doris Stüben, Geoffrey P. Glasby, Akira Usui, Jörg-Detlef Eckhardt, Bruce W. Mountain, Zsolt Berner

"Abstract - Twenty-seven marine Mn and Fe deposits chosen for their diverse origins have been analyzed for five platinum-group elements (PGE). The PGE display their highest concentrations in hydrogenous Mn crusts and nodules, lesser concentrations in diagenetic nodules and two to three orders of magnitude lower concentrations in hydrothermal Mn and Fe crusts. This difference of behavior reflects the well-known fractionation of Mn and Fe from the other transition elements, rare earth elements (REE) and PGE in hydrothermal Mn and Fe crusts. Pt, Ru, Rh, and Ir show a close geochemical coherence in these deposits and are differentiated from Pd which shows a negative anomaly with respect to the other PGE in hydrogenous and diagenetic Mn deposits. Pd is less depleted than the other PGE and the Pd anomaly much less pronounced in the hydrothermal Mn and Fe crusts relative to the hydrogenous and diagenetic Mn deposits.Stability field diagrams show no evidence for the oxidation of Pt to the tetravalent state in seawater as suggested by some authors. Rather, Pt appears to be present in seawater as Pt(OH)2 0. Adsorption of Pt(OH)2 0 onto the surface of Mn and Fe oxyhydroxide minerals may explain the enrichment of Pt in marine Mn deposits. However, Pt metal is the thermodynamically stable solid phase of Pt under seawater conditions and reduction of Pt(OH)2 0 to Pt metal, particularly in the vicinity of the oxygen minimum zone, is possible, although the high Ce/La ratios of the Co-rich Mn crusts do not support this hypothesis. Pt, Ru, Rh, and Ir display their maximum concentrations in the Corich Mn crusts. This may reflect, among other things, the low growth rates of these deposits. The stability field diagram of Pd shows that Pd is undersaturated in seawater and occurs in seawater dominantly as PdCl4 2- and anionic mixed-hydroxide-chloride complexes. This would explain the anomalous position of Pd among the PGE with respect to its uptake into marine Mn deposits. A study of inter-element associations indicates that the incorporation of the PGE from meteoritic dust plays only a minor role in the uptake of these elements into marine Mn deposits. The PGE remain the most poorly studied group of elements in marine Mn deposits. The data presented here emphasize the need for the establishment of a more comprehensive database of the PGE in marine Mn deposits in order to understand more fully their uptake into marine Mn deposits and their pathways through the oceans."

Jan 1, 1999

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By W. A. Padgham, J. A. Brophy

About 85 % of the 350 tonnes of gold produced by 25 mines in the onhwe t Territories (NWT) since 1935 has come from the Yellowknife-area mines, Con and Giant , which exploit shear zones in Archean mafic volcanic of the Slave Structural Province. Four percent of the total production has been from Archean iron formation-hosted depo its, mainly from Lupin Mine, which today produces more gold than Con and Giant combined and has been primarily responsible for the increase of WT gold output from 5 to 12 tonne per year since 1981. The remaining gold ha been won from the following deposit typesall but the last being in Archean rock : sedimentary-volcanic contact depo its uch a Discovery and Salmita (10 %); turbidite-hosted quartz-vein depo its uch a Camlaren and Ptarmigan (1%); Proterozoic deposits such as Shear Lake and Fox (1#) . All but I% of WT gold has come from the Archean Slave Structural Pro ince, which is also the premiere exploration area for gold deposit types that have yet to be productive in the NWT. These types include stratabound gold in mafic and in felsic volcanic rocks (eg. , at Indin Lake and Courageous Lake, respectively) as well as gold in plutonic rocks (eg. Anialik Gnei Complex). Deposits similar to those in the Slave have al o been found in the Archean Ennadai Belt of the Churchill Structural Province. In the Cordillera. there is potential for placer gold and for gold associated with Cretaceou intrusions.

Jan 1, 1986

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By M. Pearson, W. Bristowe, A. Hanson

"There's no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors' experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

"During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests.In the current case, a composite sample of gold ore is dedicated to a Gravity Recoverable Gold (GRG) test. The properties of interest are the head grade of gold, the size distribution of the material, and the gold assay per size class. The sample is mixed and a sub-sample is taken to measure the feed properties: the size distribution and the gold assay per size class. The remaining material of the sample is subject to the first stage of concentration using the laboratory Knelson concentrator. The concentrate is analysed in its entirety, while a sample of tailings is taken for the same analysis. The remaining part of tailings is subject to grinding to feed the second and third stages of concentration. Similar sampling is performed at each stage.The concentration performances are analysed in light of these measurements. But what is the accuracy of the measurements of the properties? Pierre Gy’s theory of sampling, associated with a heterogeneity model built using the GRG test results, will answer this question. The current paper presents, through a real example, the calculation of the errors of the measurements of size distributions and gold assays performed during the GRG test. The uncertainties of the concentration performances and liberation size estimate are then calculated and their impact on the results interpretation is analysed.INTRODUCTIONDuring the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests. In order to take into account the ore variability in terms of gold deportment, it is recommended to perform variability studies (Dominy, Murphy, & Gray, 2011, Dominy, 2013) using samples representing various horizons or years of production. But for a given ore type, it can be necessary to perform many tests with different operating conditions (Brochot, 2012a). In that case, the variability of the samples is not due to the heterogeneity of distribution of the deposit, but only on the heterogeneity of constitution of the primary sample. The level of confidence associated with the estimated performance parameters is directly linked to the overall error (including sampling error) of the measurements performed during the tests."

Jan 1, 2016

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By J. Ipinza, J. P. Ibáñez, Casas J., S. Cortés

Copper powder generated during the treatment of electro-metallurgical bleeds by reactive electro- dialysis (RED) had totally reduced the content of ferric ions in acidic synthetic electrolytes (Cu (II)- Fe (III) – H2SO4). In batch and columnar experiments 100% of the ferric ions were reduced to ferrous ions with an extremely high kinetics. A preliminary conceptual design for reducing ferric ions based on an integrate RED- Column for treatment of electro-winning bleed system is discussed. This system is able to recover simultaneously sulfuric acid and copper powder, which will reduce ferric ions. INTRODUCTION It is well known the negative effect of ferric ions in the copper electro-winning process. The increase of ferric content in the electrolyte reduces the current efficiency, i.e., there is an increase in the energy consumption, and changes the surface morphology of the copper deposit (Das, Gopala & Krishna, 1996; Vargas & Parra, 2013). The increase of the specific energy consumption due to the loss of current efficiency occurs by the reduction reaction of ferric to ferrous ions in the cathode, at the anode the ferrous ions are slowly oxidized to ferric ions (Shaw, Dreisinger, Lancaster, Richmond & Tomlinson, 2004). To control the level of iron in the electrolyte, bleeds are needed; this bleed electrolyte containing copper, sulfuric acid, cobalt, iron and other impurities normally is waster, which increased the production cost of the plant (Milbourne, 2002; Mckevitt & Dreisinger, 2009). Then, permanent efforts oriented to treat those bleeds to avoid losses of valuables components are made; among them are use ion exchange resins (Shaw et al., 2004; Mackevitt et al., 2009), chemical precipitation (Izadi, Mohebbi, Amiri & Izadi, 2017) and electrodialysis (Cortés, Ipinza & Ibáñez, 2013). The last one allows to the simultaneous recovery of sulfuric acid and copper powder. If one of the valuables obtained by treating the bleed can be used to reduce ferric ion concentration in the electrolyte could be an important asset. This issue at laboratory scale is reported in this work, the use of copper powder, generated by reactive electro-dialysis when treating synthetic acidic electro-metallurgical bleeds, for reducing ferric ions in acidic electrolytes.

Jan 1, 2019

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By G. J. Arseneau

ABSTRACT Mineral resource statements are reported as tonnage (volume × density) and grades. Effort is expended to accurately estimate the volume and grade, but accurately determining bulk density is often overlooked. Oversimplification of density modelling can result in potentially serious errors in tonnage estimates and over- or underestimation of metal content. A reliable bulk density model requires an adequate database and a good understanding of density variability, along with grade and geology. In this paper, the author summarizes density measuring techniques, draws on examples of simple and complex grade-variable density domains, and discusses improved approaches for minimizing density estimation errors.

Jan 1, 2014