Search Documents

By Bradford C. Wesstrom

An overview of the challenges encountered at the Freeport McMoRan El Paso Copper Refinery with higher concentrations of antimony electrolyte will be shared. The observations will cover the detrimental effects on copper starting sheets, commercial cathodes and anode slimes. The study will show negative effects on quality and productivity. Experimental work will utilize a test cell to study the effects on electrolytes by different Antimony, Arsenic concentration and anode molar ratio. Best practices will be shared for producing high quality cathodes while effectively managing the detrimental effects of higher antimony electrolyte.

Jan 1, 2014

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By F. Parada

During copper smelting and converting processes, slag generated is pyrometallurgically cleaned and then disposed, containing around 1 % of this metal. However, important amount of molybdenum initially contained in concentrates also goes to the slag phase. Research on molybdenum recovery from water granulated slags using acid leaching at low temperatures was conducted to find an efficient way for molybdenum extraction with lower magnetite in the slag. However because of the high fayalite content high acid consumption was found. Molybdenum can be recovered from solution using ionic exchange resins, but high silica content interferes with extraction. Some studies addressed to minimize silica extraction as well as alternatives of selective silica precipitation in order to develop a technically feasible process.

Jan 1, 2007

By C. Cekerevac

The paper addresses some geotechnical issues related to the construction of the Deriner dam and HEPP. Design considerations and rock stabilization measures are presented for the excavations which took place in a highly fractured and weathered rock mass prevailing on site. Particularly, the shallow excavations for the overflow spillways tunnels are discussed. These present huge openings that are 12 m wide and 18 m high in portal areas, with an overburden of approximately 20 m, for which numerical finite element analysis and structural discontinuity analysis have been performed to ensure safe excavation process and future operation.

May 1, 2009

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By Hong Zhong, Shuai Wang, Gang Zhao, Lanqing Deng, Guangyi Liu

In this paper, three novel surfactants containing double reactive centers(-CONHOH and –CONH-), double hydrophobic groups were designed and synthesized as collector for separation of diaspore and aluminosilicate minerals, such as N-(4-(hydroxyamino)-4-oxobutyl)octanamide (HA-8), N-(4-(hydroxyamino)-4-oxobutyl)decanamide (HA-10) and N-(4-(hydroxyamino)- 4-oxobutyl) -dodecanamide (HA-12). The adsorption mechanism of N-(4-(hydroxyamino) -4-oxobutyl)alkylamides (HA) onto diaspore was also investigated by FTIR spectra, zeta potential measurement and DFT. The flotation results demonstrated that three collectors all exhibited superior collecting power to diaspore and selectivity against kaolinite and illite, and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. Moreover, HA-12 was a superior collector than other two collectors for bauxite separation. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 6.0, HA might chemisorb on diaspore surfaces through Al-O coordination bonds formed by binding its –C(=O)NHOH or –C(=O)NH– chelate groups with aluminum atoms on diaspore surfaces. HA’s unique properties, such as characteristic bond patterns onto diaspore surfaces, double hydrophobic groups, and intermolecular hydrogen bonds between neighboring HA molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore.

Jan 1, 2016

By F. S. Su, P. Z. Pan, X. T. Feng, F. Yan, W. W. Ji

"This paper aims to simulate the spalling failure behavior in hard rock based on a self-developed numerical model, i.e. a rock discontinuous cellular automaton (RDCA). A crack initiation and propagation criterion is proposed based on the plastic strain, which is used to link the continuity and discontinuity during the failure process. The discontinuities of rock, such as cracks and other internal boundaries, are represented by discontinuous displacement functions, i.e. tip enrichment and step enrichment. The partition of unity is used to improve integral precision of the elements intersected internal boundaries, which is traced by a level set method. Arbitrary crack geometries can be conveniently represented and it does not require any remeshing in the modeling of crack initiation, propagation and coalescence. Numerical modeling of excavation in hard rock using RDCA is conducted. The spalling failure process of hard rock induced by excavation is well simulated. The depth and shape of hard rock spalling failure are good agreement with in situ observation.INTRODUCTIONThe excavation in rock mass is more and more popular. At the same time, the disasters, such as rock burst, rock spalling and falling etc, induced by excavation are quite prominent. Numerical modeling is an important way to help us understand the failure mechanism of rocks. Many numerical methods have been used to simulate the excavation of rock mass. For example, the finite element method (FEM) (Karakus and Fowell, 2003), the discrete element method (DEM)(Cundall and Strack, 1979, Labra et al., 2008), Finite difference method (FDM)(Zhu et al., 2009), Element Free Galerkin Method (Belytschko et al., 1994), Discontinuous displacement analysis (DDA) (Shi, 1988) and Boundary element method (BEM) (Katsikadelis, 2002, Chen and Hong, 1992) are commonly found in the stability analysis of excavation in rocks. In the modeling of crack propagation or excavation, most of these methods are tedious since the internal boundaries have to be consistent with the element boundaries. And in many cases, the remesh has to be conducted. In recent years, people are interested in particular types of FEMs, such as the extended finite-element method (XFEM), the particle discretization scheme finite-element method(PDS-FEM(Hori et al., 2005, Oguni et al., 2009)), the combined finite-discrete element method (FEM/DEM) (Munjiza and Wiley, 2004, Cai, 2008) and spectral-element method(Gharti et al., 2012) etc."

Jan 1, 2015

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Doris Stüben, Geoffrey P. Glasby, Akira Usui, Jörg-Detlef Eckhardt, Bruce W. Mountain, Zsolt Berner

"Abstract - Twenty-seven marine Mn and Fe deposits chosen for their diverse origins have been analyzed for five platinum-group elements (PGE). The PGE display their highest concentrations in hydrogenous Mn crusts and nodules, lesser concentrations in diagenetic nodules and two to three orders of magnitude lower concentrations in hydrothermal Mn and Fe crusts. This difference of behavior reflects the well-known fractionation of Mn and Fe from the other transition elements, rare earth elements (REE) and PGE in hydrothermal Mn and Fe crusts. Pt, Ru, Rh, and Ir show a close geochemical coherence in these deposits and are differentiated from Pd which shows a negative anomaly with respect to the other PGE in hydrogenous and diagenetic Mn deposits. Pd is less depleted than the other PGE and the Pd anomaly much less pronounced in the hydrothermal Mn and Fe crusts relative to the hydrogenous and diagenetic Mn deposits.Stability field diagrams show no evidence for the oxidation of Pt to the tetravalent state in seawater as suggested by some authors. Rather, Pt appears to be present in seawater as Pt(OH)2 0. Adsorption of Pt(OH)2 0 onto the surface of Mn and Fe oxyhydroxide minerals may explain the enrichment of Pt in marine Mn deposits. However, Pt metal is the thermodynamically stable solid phase of Pt under seawater conditions and reduction of Pt(OH)2 0 to Pt metal, particularly in the vicinity of the oxygen minimum zone, is possible, although the high Ce/La ratios of the Co-rich Mn crusts do not support this hypothesis. Pt, Ru, Rh, and Ir display their maximum concentrations in the Corich Mn crusts. This may reflect, among other things, the low growth rates of these deposits. The stability field diagram of Pd shows that Pd is undersaturated in seawater and occurs in seawater dominantly as PdCl4 2- and anionic mixed-hydroxide-chloride complexes. This would explain the anomalous position of Pd among the PGE with respect to its uptake into marine Mn deposits. A study of inter-element associations indicates that the incorporation of the PGE from meteoritic dust plays only a minor role in the uptake of these elements into marine Mn deposits. The PGE remain the most poorly studied group of elements in marine Mn deposits. The data presented here emphasize the need for the establishment of a more comprehensive database of the PGE in marine Mn deposits in order to understand more fully their uptake into marine Mn deposits and their pathways through the oceans."

Jan 1, 1999

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By W. A. Padgham, J. A. Brophy

About 85 % of the 350 tonnes of gold produced by 25 mines in the onhwe t Territories (NWT) since 1935 has come from the Yellowknife-area mines, Con and Giant , which exploit shear zones in Archean mafic volcanic of the Slave Structural Province. Four percent of the total production has been from Archean iron formation-hosted depo its, mainly from Lupin Mine, which today produces more gold than Con and Giant combined and has been primarily responsible for the increase of WT gold output from 5 to 12 tonne per year since 1981. The remaining gold ha been won from the following deposit typesall but the last being in Archean rock : sedimentary-volcanic contact depo its uch a Discovery and Salmita (10 %); turbidite-hosted quartz-vein depo its uch a Camlaren and Ptarmigan (1%); Proterozoic deposits such as Shear Lake and Fox (1#) . All but I% of WT gold has come from the Archean Slave Structural Pro ince, which is also the premiere exploration area for gold deposit types that have yet to be productive in the NWT. These types include stratabound gold in mafic and in felsic volcanic rocks (eg. , at Indin Lake and Courageous Lake, respectively) as well as gold in plutonic rocks (eg. Anialik Gnei Complex). Deposits similar to those in the Slave have al o been found in the Archean Ennadai Belt of the Churchill Structural Province. In the Cordillera. there is potential for placer gold and for gold associated with Cretaceou intrusions.

Jan 1, 1986

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016