Search Documents

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

By Mike Anderson

The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd is in excess of 450 million dollars. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trails where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trails will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work.

May 1, 2003

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012

By John Campbell, William Trahant

"Total Quality Management (TQM) is becoming a reality in the mining industry. Widely adopted in the manufacturing and services industries, TQM has become the operating style of choice in numerous mining companies across the Americas and Australia. Iron Ore Company of Canada, Inco, MSA, Graniterock, Magma Copper, and CRA's Hamersly Iron - all are pioneers of TQM. These companies and others are confronting the challenges of implementing TQM and are managing the changes required of their people and cultures. What these companies are doing, why they are doing it, and how they are successfully managing the changes are the subjects of this paper.Driving the need for change in these organizations are a host of issues, some of which all mining companies are facing. Requirements from customers for ISO 9000 certification is becoming one of the initial motivators for Total Quality Management. These standards, commonly used in manufacturing throughout the European Community (EC), emphasize quality in the processes that create outputs, instead of just the outputs themselves. Iron Ore Company of Canada, for instance, responding to the requirement of one of its customers, British Steel, has become one of the first mining companies to meet the quality standard. Suppliers who meet the standards are highly desirable to customers who are themselves operating under the ISO or their national quality guidelines."

Jan 1, 1995

By M. Lahtinen, B. Saxén, M. Latva-Kokko

The conventional jarosite precipitation process with neutralization by zinc calcine is widely utilized in the zinc industry. However, it has a significant drawback of causing losses of valuable metals like zinc, lead and silver to the jarosite. This comes mainly from the content of these metals in the calcine used for neutralization. As the zinc plants today want to maximize metal recoveries and minimize the amount of residues, this matter has become more and more relevant for zinc producers. Outotec developed and patented in early 2000 an improved version of the jarosite precipitation process in which the need for neutralization can be minimized, thus the metal losses to the jarosite also can be minimized. At the same time, the iron content of the jarosite increases and the amount of produced jarosite is smaller. The main feature of this process is to start the precipitation from ferrous iron after having reduced all the iron by zinc concentrate in a separate step before jarosite precipitation. Iron is then oxidised back to the ferric form simultaneously with jarosite precipitation. By this method, the formation of sulphuric acid is only half that compared to the conventional method and the need for calcine for neutralization can be avoided. High mixing and oxygen dispersion capability are needed in this jarosite precipitation process. Such capabilities are found in the Outotec OKTOP® reactor series. High performance reactors are not only needed to generate high quality precipitates, but also to maximize oxygen utilization; i.e., to minimize operation costs. Outotec’s latest development in this area is the OKTOP® plant product in which not only the reactors, but also all the accessories are designed, manufactured and delivered by Outotec. One responsible supplier ensures efficient and fast delivery and can provide mechanical and performance guarantees for the entire plant unit.

Jan 1, 2016

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2' r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By Marc C. Bétoumay

Workplace safety, health, climatic conditions and rising oil prices are aspects that are important to the mining industry. The need for cleaner energy for underground mine vehicles is requiring serious consideration. A number of alternate energy systems offer clean solutions to diesel emissions while maintaining the current liberty of vehicle movement. This watershed article provides a broad comparison of cleaner diesel and alternative energies for underground production vehicles. Most alternate energies and clean diesel have already been tested in underground production vehicles. There are no technology gaps that would prevent the development of commercial alternative energy power plants, but in the case of alternate energies, second and third generation versions will be required to fully test for safety and operation viability. Full regulatory development is also required and could be done in parallel to power plant testing. Vehicle operation and maintenance manpower would be the same for alternate energy application as for clean diesel. Capital cost for alternate energy power plants will remain higher until the medium term. Owing to significant ventilation savings possible with alternate technologies, operating costs would be reduced.

May 1, 2011

By Ahmad Ghahremaninezhad, Noelene Ahern, Yeonuk Choi

Arsenic (As) is a toxic element and is a major contaminant in the extraction processes of some metals (e.g. gold and copper). Due to the toxicity of arsenic species, its removal from As-containing streams from extractive metallurgy processes and safe disposal is absolutely necessary. For nearly complete removal of waste arsenic species from metallurgical process streams, it is required to have arsenic in its pentavalent state (As5+ species). This study presents an oxidation process for arsenic species with air or oxygen gas as oxidant. Activated carbon (AC) or other carbon based materials are used to catalyse the oxidation reaction. Air or oxygen gas is the only consumed reagent which makes the economy of the process very attractive. The oxidation reaction can be carried out at ambient conditions (room temperature and atmospheric pressure) in less than 24 hours.

Jan 1, 2014

By J. Walenzyk

This report investigates the limited use of super large backhoes in surface mines around the world. The demand for super large (> 700 t) hydraulic excavators is rising and most of the machines are sold as front shovel (FS) application. Despite advantages in faster cycle times super large backhoe (BH) machines are a minority (ca. 1% of the total machine population). This investigation is based upon the comparison between the volumes available to the BH and FS in one block and before the machine needs to move. The working conditions are created with standard parameters as given by Original Equipment Manufacturers of hydraulic excavators regarding bench height, angle, and material density. The travel amount of both machine types is derived from these volumes and compared. Furthermore, the travel amount of super large BHs is compared to the travel amount of smaller mining BHs and evaluated based on attachment length and bucket size. The calculations conclude that the volume of material recoverable in a single spot is about 75% higher for FSs. This leads to an increased travel for BHs. The combination of both the increased appearance of electrical driven machines (in the class of > 700 t excavators) and the travel amount lead to a high risk of damaging the cable or the excavator. Enlarged wear on the travelling parts is also attended by the higher travelling. A direct comparison of commonly found working set ups shows that the ratio between volumes is 32% which leads to an increased travel amount. In comparison with a 250 t BH, the calculation shows that the smaller BH is able to reach nearly 50% of the volume of the super large BHs. The main reason for this is the respectively high reach on smaller machines which, combined with other factors, leads to a significantly higher number of BHs in lighter classes.

Aug 1, 2013

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By M. Pawlik, E. Arinaitwe, V. Ferrera

A series of flocculation tests were performed on dilute quartz suspensions with the use of five polyacrylamide-based flocculants of similar molecular weights but of different degrees of anionicity. The tests were performed as a function of ionic strength and pH. The macromolecular conformation of flocculants in solution was assessed through intrinsic viscosity measurements under the same physicochemical conditions as those of the flocculation tests. It was generally found that the flocculating efficiency of the polyacrylamides correlated with their ability to coil or stretch in solution. Polyacrylamides with the degrees of anionicity on the order of 10-18% showed the highest flocculating efficiency in terms of the settling rates of the flocculated solids and the residual turbidity of the resulting supernatant. At the same time, these most effective flocculants were also found to exhibit the greatest tendency to coil and stretch in solution. This result suggests that the flocculating power of a flocculant is determined not only by its ability to adsorb onto (and bridge) fine particles but also on its ability to conform to the size of the resulting floes.

Jan 1, 2009