Search Documents

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By J. Cui, Z. Meng, W. Zhao

"The decomposition of rare earth concentrates containing bastnasite and monazite by alkali solutions has been investigated. A slurry of the rare earth concentrate and the alkali solutions was calcined at different temperatures. The impacts of calcination temperature on the decomposition of rare earth minerals, the oxidation of cerium, the deportment of fluorine and phosphorous, and the adaptability of the method to the different grades of rare earth concentrate were all studied. A possible technique for comprehensive recovery is proposed in which the chemical elements such as rare earth, fluorine, phosphorus, calcium, iron and thorium could be recycled or recovered. INTRODUCTIONThe liquid alkali decomposition method is an important technique for the decomposition of mixed rare earth concentrates. The technique is relatively clean compared with the sulfuric acid roasting method. However, its operation is intermittent rather than continuous. The two-step solid-liquid reaction and the subsequent water washing make it not very suitable for mass production and application. An important reason for the disadvantage is that an additional process of ""calcium removal by acid leaching"" is needed for the technique. The content of calcium in Baotou rare earth concentrates is usually 6-12%. The requirement of the current technique is that the content of calcium should be reduced to about 0.2% after the calcium removal process. Otherwise, the decomposition and leaching of rare earth will be affected. Therefore, calcium removal by acid leaching is a necessity before the alkali decomposition process is carried out. Research on different alkali decomposition techniques has been conducted with prior calcium removal by acid leaching (Xu, 1995; Yu, 1993; Han, Li, Chang, Liu & Xu, 1985). There have been some investigations of direct decomposition of the bastnasite (Feng, Pan & Li, 1998; Zhao, Zhang, Yang & Liu, 2002)and monazite (Sun, Li, Li, Su, Zhao & Liu, 1998; Zhou, 2005) by alkali-liquid, however, all studies were carried out in solid-liquid reaction system, and continuous calcination studies have not been reported.This paper investigates the process of direct decomposition of Baotou rare earth concentrates by continuous calcination with concentrated alkali. Using the rotary tubular electric furnace, the mixture of rare earth concentrate and concentrated alkali solution were decomposed continuously. Satisfactory decomposition results were achieved. A method for clean processing and comprehensive resource recovery from Baotou rare earth concentrates is proposed."

Jan 1, 2012

By Graham Farquharson, Jame Marshall

"Mining towns have always been an important part of Canadian geography. Many Canadians grew up in them. The frontiers of northern Canada would be a lot closer to the United States border but for the pioneering of new mines, new towns, and new transportation routes. Names such as Labrador City, Chibougamau, Val d’Or, Rouyn-Noranda, Kirkland Lake, Timmins, Sudbury, Red Lake, Thompson, Flin Flon, Yellowknife, Whitehorse,Trail and Kimberley are some of the better known larger communities that have grown to become major commercial and government centres, but which started as the base for a mining development.Many other smaller towns never grew beyond being small communities, dependent upon the local mine and many of these are still alive, but perhaps not quite what they used to be. In this list would be Buchans, Schefferville, Chapais, Cadillac, Virginia town, Lynn Lake, Uranium City, Pine Point, and Keno Hill.Nevertheless, all these towns and dozens more like them were residential communities where people lived and raised families and were quite accustomed to being days from the major centres of Montreal, Toronto, Edmonton and Vancouver, and not just hours away as wet end to measure travelling time today."

Jan 1, 1996

By N. Shi, T. G. Joseph

ABSTRACT One-twentieth-scale field trials for conventional and concept dipper designs were compared to mid- and ultra-class-sized conventional dipper performance. Digging effort was used as the performance indicator for comparison. It was shown that linear relationships exist between dipper capacity, suspended hoist load, and peak hoist load. A ratio of conventional and concept dipper performance at the 1/20th scale was then evaluated to allow prediction of the performance of an ultra-class concept design using an independent ultra-class conventional dipper dataset. The outcome indicated a peak hoist requirement of 15.5% less to achieve the same production as the conventional design.

Jan 1, 2011

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By R. D. Brown

"Concerns over possible additional involvement of governments in Canada's mining industry and its adverse effects on the industry 's growth were a frequent topic of conversation at the recent Annual General Meeting of the CIM.Still painfully fresh in the minds of industry leaders are the disastrous results of the federal/provincial scramble over resource revenues which followed the relatively high metal prices witnessed in 1973/1974. At current metal prices, it is not surprising, then, that a nagging fear persists that these governments may once again restructure tax and other rules to the detriment of the industry and the country.This month, Tax Notes recalls some of the progress which the industry and governments have made in 1979 in the taxation of the resource sector, and urges that higher metal prices be viewed in light of the costly exploration, development and production efforts which will be required for the industry to continue to play its important role in our economy.IntroductionAt the Annual General Meeting of The Canadian Institute of Mining and Metallurgy, held in April, 1980, it was abundantly clear that there is widespread concern in Canada's mining industry that this country's tax regime may once again be blasted by ill winds of change.A stable and more favourable tax climate, as well as higher metal prices and profits, made 1979 almost a golden year for Canadian mining. However, from the tax viewpoint at least, there are some spots on the silver lining as apprehensions grow that the well-heralded battle between federal and provincial governments over oil and gas may spread to the mining sector, with serious damage to the industry and its newfound federal-provincial cooperation."

Jan 1, 1980

By Gautier Njiekak

The current study provides an experimental approach that aims at documenting the effects of different phases of CO2 (gas, liquid, supercritical fluid) on rock seismic responses. This has implications on obtaining quantitative estimates of fluid saturations for geological storage. The ultrasonic pulse transmission technique is the underlying methodology used in this work. Unlike previous rock physics studies involving CO2 as pore fluid, care is taken to fully saturate the studied samples and also to separate pore fluid effects from pore pressure build-up effects during the experiments. This allows to record seismic effects that are solely reflective of changes in the pore fluid properties. Measurements were done on a CO2 saturated Berea sandstone. Laboratory results show P- and S- waveform variations (velocity, amplitude) in response to CO2's varying phase state. Overall, CO2 phase changes (gas to liquid and gas to supercritical fluid) are marked by a drop in velocities, with the drop being smaller and less immediate over the gas-supercritical fluid transition than over the gas-liquid transition.

Jun 1, 2012

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By Andre L. Du Preez

Global mine hoisting regulations require safety fall arrest systems to be installed on vertical conveyance systems capable of safely decelerating and supporting a fully loaded conveyance in the event of a rope severance. Most current arresting systems are incapable of producing controlled safe deceleration rates. Although safety ?dogs? achieve marginally acceptable results on wooden guides, difficulties arise in achieving safe deceleration performance requirement where safety arrest systems operate on steel shaft guides. Previously, arresting systems capable of operating with steel guides have been incapable of producing controlled deceleration rates during the arresting of free-falling conveyances. Most are ?instanton? systems, whereby an occupant inside a conveyance being arrested would be subjected to unacceptably high deceleration forces. This paper briefly highlights the background to the selection process of Rio Tinto?s Technical Staff of a suitable Mine Conveyance Safety Fall Arrest System for #1 Shaft at Rio Tinto Oyu Tolgoi Mine, Mongolia. It also describes the Drop Test and Free Fall Test procedure and the results leading to the acceptance of the Horne Group Levelok® Emergency Braking Technology for the Oyu Tolgoi #1 Shaft in Mongolia. The paper highlights Rio Tinto?s primary objective for the selection of this advanced technology on their primary production shaft cage system as an emergency safety catch braking system combined as an advance hydraulic chairing system. It describes the design and operational parameters and the 'Fail to Safe' interfacing with current automated mine hoist systems.

Aug 1, 2013

By R. W. Lawrence, A. Bruynesteyn

"Pre-oxidation of refractory pyritic concentrates by biological leaching to enhance the recovery of gold and silver in cyan ideation has been investigated. The results of laboratory tests on three concentrates are presented. In all cases substantial increases in precious metal recoveries were obtained following the pre-treatment. For one concentrate, gold recovery of 81% was achieved following an 87% oxidation of pyrite, compared with 24% recovery by direct cyanidation of non-oxidized concentrate. Gold and silver recoveries from the other concentrates were increased from the range 60-78% to over 90% and from 80-86% to over 98% respectively. Operating parameters are discussed and methods of maintaining high oxidation rates are evaluated. Methods of employing this pre-oxidation technique in commercial practice are described.IntroductionMany of the gold and silver deposits now being developed contain precious metals finely disseminated in sulphide minerals such as pyrite. These ore s often present considerable resistance to metal recovery. The ease with which gold may be extracted is usually related to grain size and its manner of distribution within the host mineral. In many cases, a significant percentage of the gold may occur in submicroscopic form, or in solid solution with pyrite, so that even very fine grinding fail s to liberate the metal for recovery by cyanide leaching. Such ores are often termed refractory. Even in cases where liberation by fine grinding is practicable, high cyanide and lime consumption may be experienced due to the presence of specific sulphide minerals, and poor metal recovery may result.Pre-oxidation methods for refractory ore s and concentrates are commonly used to improve precious metal recoveries. Roasting, for example, as a pre-treatment to cyanidation, removes harmful constituents by oxidation or volatilization, and liberates gold from pyrite. In some cases, however, this method of pre-oxidation can result in poorer metal recovery, particularly of silver, due to fusion and the formation of clinker, and the formation of compounds which consume cyanide in the subsequent metal recovery stage. Difficulties in compliance with environmental pollution regulations may also be encountered."

Jan 1, 1983

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By M. Rafiee

Indoor physical security, as a perpetual and multi-layered phenomenon, is a timeintensive and labor-consuming task. Various technologies have been leveraged to develop automatic access control, intrusion detection, or video monitoring systems. Video surveillance has been significantly enhanced by the advent of Pan-Tilt-Zoom (PTZ) cameras and advanced video processing, which together enable effective monitoring and recording. The development of ubiquitous object identification and tracking technologies provide the opportunity to accomplish automatic access control and tracking. Intrusion detection has also become possible through deploying networks of motion sensors for alerting about abnormal behaviors. However, each of the above-mentioned technologies has its own limitations. This paper presents a fully automated indoor security solution that leverages an Ultra-wideband (UWB) Real-Time Locating System (RTLS), PTZ surveillance cameras and a Building Information Model (BIM) as three sources of environmental data. Providing authorized persons with UWB tags, unauthorized intruders are distinguished as the mismatch observed between the detected tag owners and the persons detected in the video, and intrusion alert is generated. PTZ cameras allow for wide-area monitoring and motion-based recording. Furthermore, the BIM is used for space modeling and mapping the locations of intruders in the building. Fusing UWB tracking, video and spatial data can automate the entire security procedure from access control to intrusion alerting and behavior monitoring. Other benefits of the proposed method include higher accuracy and robustness, more complex query processing, and interoperability with other BIM-based solutions. A prototype system is implemented that demonstrates the feasibility of the proposed method.

Aug 1, 2013

By A. L. Mackie

Arsenic is a highly toxic element and a known human carcinogen. It is often a contaminant in mine water discharges, particularly from gold mining and roasting operations, and has been found at concentrations as high as 4 g/L. Increasingly stringent controls on the concentration of arsenic allowed to be discharged into the environment cannot always be met by current treatment processes and thus enhanced technologies are required to achieve low treated effluent concentrations at reasonable costs. A novel two-step physicochemical treatment process was developed and tested at the bench-scale using synthetic mine water solutions (SMWs) in order to reduce arsenic concentrations in treated effluent to exceed current discharge regulations. The process includes chemical coagulation with ferric sulphate and ballasted flocculation for enhanced solid-liquid separation. The SMW contained 59 ± 2 mg/L arsenic with a slightly alkaline pH. The effect of arsenic speciation on the process was tested by using either arsenite, As(III), or arsenate, As(V), in the SMW solutions. Tests were performed at cold temperature (3 ± 1 °C) to ensure the process? efficacy year-round in northern climates. Arsenic in As(V) SMW solutions was removed to a final total concentration of 0.0054 ± 0.002 mg/L, almost half the current recommended allowable drinking water concentration of 0.010 mg/L. As(III) was removed to a concentration below the Metal Mining Effluent Regulations? (MMER) current limit of 0.50 mg/L, to 0.32 ± 0.06 mg/L, with double the coagulant dose used in Stage 1 for As(V) removal. Oxidant addition at a concentration of 5 mg KMnO4/L in Stage 2 resulted in final total arsenic concentrations of 0.017 ± 0.002 mg/L and pH adjustment with lime in Stage 2 resulted in 0.0415 ± 0.0007 mg As/L in treated As(III) SMW. Both of these modifications to the process reduced arsenic concentrations to below proposed new MMER limits (i.e., 0.10 mg/L). This two-stage treatment process was shown to reduce arsenic concentrations to well below current treatment guidelines while reducing or eliminating chemical oxidant demand.

Aug 1, 2013

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019