Search Documents

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By T. Haubold, K. Ortner, T. Jung, D. Roth-Fagaraseanu, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. Erosion of the blisk aerofoils in service reduces engine performance, and can result in short shop visit cycles. This significantly increases the life cycle cost of these components, particular when considering that eroded aerofoils can't be exchanged easily for blisks during refurbishment. Shop visit cycle times can be extended and maintenance costs can be reduced through the application of an effective protective coating. The ongoing development of an erosion resistant coating and deposition process suitable for coating complex blisk geometries is described here. The coating is a multilayered W /TiB2 system exhibiting superior erosion resistance compared to known single- and other multilayer concepts. A modified sputter process is used to enable coating even of blisk geometries with shadowed surface to competitive recurring cost.

Jan 1, 2006

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By Mike Broczkowski, Laura Dewhirst, Kieran Large, Angelo R. Fernando, Heather Daigneault, Jim Johnson, Randy Wiens

The radioactive isotope radium 226 is a contaminant of potential concern in effluent waters from metal mining operations in Canada. Acceptable release levels of radium 226 are governed by Metal and Diamond Mining Effluent Regulations. Since radium is invariably present as a companion element in uranium ore, monitoring and controlling of radium 226 is a must for uranium mining operations. Measurement of radium 226 is traditionally carried out through a radiochemical technique involving selective co-precipitation of radium with barium sulphate followed by alpha spectroscopy for quantification. As of 2010, Cameco has also been using an ICP-MS based radium analysis method developed in collaboration with a research team at Trent University, Peterborough, Ontario. This method, which is highly automated and requires significantly less sample handling, with improved turn-around-times, is being used by Cameco site laboratories at the McArthur River and Cigar Lake mines as well as the Port Hope Conversion Facility. This paper compares the benefits and drawbacks of this new method, compared to the traditional alpha counting procedure drawing from almost ten years of field experience.

Jan 1, 2020

By G. M. Castillo

Newmont?s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By M. D. Scott

"Highland Valley Copper recently installed a semi-mobile in-pit crushing and conveyor system designed to feed both the Bethlehem and Lornex concentrators with a feed averaging 120000 tonnes per day. The system installed with a rated capacity of 12000 tonnes per hour is the highest capacity hard rock semi-mobile crushing and conveying system currently in existence.The system is designed in a manner that the crushers can be moved easily as the pit is developed in depth with conveyors extending deeper into the pit, and conveyors being moved radially from a surge pile located at the rim of the ultimate pit as the pit increases in size laterally.The system consists of two 6000 tph, 60 by 89 Krupp semimobile crushers feeding two moveable 4500 hp, 60 in. conveyors, 1.25 km long feeding a 7500 tonne live storage surge pile. Two 96 in. belt feeders installed in reclaim tunnels under the pile feed two parallel 4500 hp, 60 in. conveyors, 1.25 km long on a 12 per cent uphill grade to the two existing Lornex plant feed conveyors. A third 96 in. belt feeder, under the pile, feeds a 60 in. conveyor, loading trucks hauling crushed ore to the Bethlehem mill.A description will be given: (1) of the system's design features in which climatic extremes, operating, and maintenance characteristics were of primary importance; (2) of the way the system was constructed from components purchased internationally on an extremely tight construction schedule; and (3) of the way the system has operated during the first few months in operation during which time it demonstrated that it has met various design criteria."

Jan 1, 1988

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By C. Tong, B. Hilscher

"Sensor based ore sorting is being rapidly adopted by the mining industry. The ability to boost mill feed grade by rejecting waste grade rocks early in the process has proven revolutionary for some operations.This paper briefly reviews the current position of ore sorting in the industry, as well as abridged results from specific operations such as Barrick, McEwen, New Gold, and two others. The paper also introduces the concept of “Profit Recovery™”, the measuring of recovery based on rock profitability rather than just metal content.IntroductionSensor based ore sorting is being rapidly adopted by the mining industry. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes have been too invaluable to be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. In addition, the advent of ore sorting has also called for a new standard of recovery analysis. The answer to this is the creation of a new term and concept - Profit Recovery™.This paper evaluates the most recent results of ore sorting in the mining industry, and presents the results from five different mining operations. Additionally, this paper will discuss and evaluate the Profit Recovery™ of each of these operations. The goal of this paper is to address common concerns regarding ore sorting rejects and their actual impact on project economics.State Of The ArtOre Sorting is a sensor-based sorting and pre-concentration technology implemented before the processing stage that is used to reduce the amount of waste reporting to the mill feed. This technology can also be utilized to recover ore from previously uneconomic waste, as well as reduce the mill energy and reagent consumption (Tong, 2012). In greenfield projects, sensor-based sorting can further provide value by reducing processing capital costs. The decline of available high grade orebodies and decreasing head grades has further increased the attractiveness of pre-concentration, and subsequently ore sorting (Lessard et al., 2014).There are currently two notable types of sensor-based sorting: bulk and rock-by-rock. Bulk sorting consists of live, high tonnage sorting that can be installed on a scoop or on a conveyor belt with a diverter. Rock-by-rock is a selective sorting method that scans and sorts individual rocks on a conveyor belt, and rejects rocks using air jets or mechanical levers. Figure 1 shows a diagram for a typical air jet sorter."

Jan 1, 2018

By A. Fakhimi

The effect of porosity on mechanical behavior of rock has been studied in the past using both experimental and numerical techniques. One important aspect of this study that has not received much attention is the role of void size and distribution on the mechanical behavior of rock. In this study, the CA2 computer program that is a hybrid discrete-finite element program for two-dimensional simulation of geomaterials is used. Numerical specimens with different macro-void sizes are loaded uniaxially. The Young?s modulus, Poisson?s ratio, uniaxial strength and crack initiation stress are studied. The numerical results are compared with the database of experimental tests on Plaster of Paris specimens containing Styrofoam spheres with different void sizes and porosities. It is shown that the macro void spatial distribution is partly responsible for the scatter of the experimental data. It is also shown that not-only the porosity but also the pore size can affect the deformability, crack initiation stress and rock strength.

May 1, 2009

By T. Xue

429 As part of Inco's S02 abatement project for its Sudbury operations, a weak acid treatment plant (W ATP) was commissioned at the Copper Cliff smelter in August of 2004 to treat the weak acid streams generated by the flash furnaces, the MK reactor and the fluidized bed roaster (FBR) gas cleaning plants. The W ATP process was developed by Inco Technical Services Limited (ITSL) by means of laboratory and mini-pilot plant programs. In the W ATP process, the feed solution containing arsenic, sulphur dioxide, iron and other impurities is treated by oxidation and neutralization to form a stable precipitate for disposal in Inco's tailings impoundment area. During the commissioning of the WATP, a team of operations, maintenance, engineering, project and R&D personnel was formed, and the designed capacity was achieved in less than a month. Since then, the W A TP has been operating smoothly and the impurities, specifically arsenic, in the Copper Cliff smelting process have been effectively removed.

Jan 1, 2006

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By M. Uszko

The paper presents the conditions for determining the selection of methods for methane drainage in Polish hard coal mines. Various factors for the evaluation of methane drainage performance are used, including the methane drainage effectiveness ratio. However, as will be discussed there are limitations to the methane drainage ratio approach resulting from the characteristics of the deposits extracted in Kompania Weglowa S.A. coal mines.

Aug 1, 2013