Search Documents

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989

By G. Kachaniwsky, M. Bédard

"The Noranda Continuous Smelting Process at the Home smelter was commissioned in March 1973. The ability of the process to handle a wide variety of feed materials and a steady stream of technical innovations in recent decades has served to maintain the Home as an efficient and versatile custom smelter. This paper reviews recent technological development and capabilities in areas such as sampling and preparation of secondary and complex materials, as well as the smelting and related environmental control issues. Future trends and improvements are also addressed.IntroductionThe Noranda Home smelter commenced operations in 1927. It was originally designed to treat 910 tonnes per day of copper concentrates and ores coming from the new Home mine site. In the 19305, the company opened its doors to other mines in northwestern Quebec. Treatment of feed materials on a custom basis has, therefore, always been an important factor in the operation of the Home smelter. Throughout the years, the Home gradually increased its custom smelting capacity, while maintaining its production from the Home mine. By the early 1950s, 65% of the materials processed was from outside customers, and by 1974, this figure had increased to more than 85% . With the closure of the Home mine in 1976, the company extended its smelting operations beyond ore and concentrate, and began to treat more scrap metals and residues rich in copper and precious metal content.Corresponding with the ever-changing pattern of feed sources, the Home smelter has adopted technological improvements to meet new and challenging business conditions. The technology of the original smelter of 1927has been completely replaced over the years in the quest for improvement. One of these major changes occurred in 1973 with the start-up of the Noranda Process Reactor. This extremely efficient smelting system has been exploited to treat a wide variety of copper and precious metal (PM) containing custom materials. This paper reviews recent developments and improvements achieved at the Home smelter, in the receiving, sampling and treatments of copper and PM scrap and secondaries, with particular emphasis on the development of new technology and equipment in complex feed materials treatment."

Jan 1, 1991

By Peter Van-De-Velde

"The results of applying Japanese pumping technology to North American reclamation projects will be discussed.IntroductionEconomic high-density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.In North America where space has rarely been a facto r, industry has generally relied upon the traditional dumping of material into various waste ponds, etc . In Japan, where confined geographies and stringent environmental regulations are enforced, alternative solutions for disposal or reprocessing of waste material had to be found.High-density mineral reclamation system designed by theoretical formulas is almost impossible because solids composition, i.e. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted dredging of material to relatively dilute slurries whereas it is usually preferred to reduce water usage with its associated power and reclamation costs to a minimum and reclaim as high a concentration as possible.At Toyo Pumps North America we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions."

Jan 1, 1985

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

By Himmelman. Nicholas P.

In this paper, the hardware foundations and data collection methods of a real time collision avoidance system for electric surface mining rope shovels are described. The primary goal of the system is to help a shovel operator avoid accidentally colliding the shovel?s dipper with either a nearby haul truck or the shovel?s tracks. To achieve this goal, the system requires complete and precise knowledge of the shovel?s geometry and movement, as well as the location of any nearby haul trucks. This paper describes the subsystems created to acquire this necessary information. This system is unique in that all of its components are mounted solely on the shovel and that it is designed to be easily retrofitted to a shovel without significant modifications.

Oct 1, 2009

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By C. R. Lattanzi, M. J. Davie, L. D. Smith, J. R. Goode

"The feasibility study determines the technical and economic viability of a project at the level of accuracy required by the owner to make an investment decision. The economic analysis usually includes calculation of the discounted cash flow. Key components of the cash flow include the project capital cost, the operating costs, construction schedule, production rate, product prices and financial details.This paper examines the feasibility study for a typical mining project. The paper discusses acceptable methods for the determination of the geological and mineable are reserves. The prerequisites for the development of suitable designs, and the calculation of capital and operating costs for the mine, processing plant, and infrastructure are reviewed. Important features of the cash flow analysis and its interpretation are presented.IntroductionThe commercial development of a mineral deposit invariably requires the investment of capital in preparing the deposit for production. It has always been necessary, therefore, to demonstrate to the investor of capital that production of a saleable commodity is both technically feasible and economically viable. The instrument typically used to make these determinations is the feasibility study .Traditionally, mining companies have been rather conservative in their approach to financial management. Until about thirty years ago, the capital required to develop a new mine was most frequently provided by internal corporate cash now and virtually all of the necessary technical and economic studies were performed 'in house'. Under these circumstances, there was little standardization as to what constituted an acceptable feasibility study, and even less as to what constituted an acceptable measure of economic viability."

Jan 1, 1991

By Robert B. Parsons

"Two recent decisions by the Canadian courts could reduce the taxes paid by many profitable mines in Canada. At a time when the mining sector is hurting from an ever increasing tax burden and soft prices, the results of two cases are welcome news. Mining companies are well advised to check prior years' tax returns in the context of these developments. IntroductionSince 1976, the income tax legislation has provided a reduced rate of tax for taxpayers engaged in the mining of mineral resources, through the mechanism of the ""resource allowance"". The deduction given for the resource allowance effectively reduces the federal rate of tax by one quarter on resource profits. In general terms, ""resource profits"" are defined to include a taxpayer's income from: the production and processing in Canada of ore to any stage that is not beyond the prime metal stage (or the pellet stage or its equivalent in the case of iron ore); and, royalties computed with reference to the amount of value of production from mining operations in Canada.In computing income from these sources, the taxpayer must deduct expenses that may reasonably be regarded as applicable to those sources, with the exception of expenditures for Canadian exploration and development or financing costs.As a result of the mechanics of the calculation of the resource allowance, one quickly realizes that the lower the expenses deducted from the resource profits, the higher the resource profits and consequently the higher the 25% resource allowance. The impact of the recent court cases is to narrow the range of expenses which are required to be deducted in the determination of the resource profits.The two cases are outlined below."

Jan 1, 1991

By R. J. Twigg, S. D. Chang

"The production of heavy water, the moderator in a CANDU reactor, is examined following a flow sheet of a typical Canadian plant. The process involves the extraction and concentration of deuterium from natural water through a chemical exchange mechanism with hydrogen sulphide. Consequently, corrosion problems associated with sour environments – the use of hydrogen sulphide - are an everyday problem and have led to the development of a highly refined materials selection and testing program to prevent equipment from failing prematurely.IntroductionHeavy water is a naturally occurring compound in ordinary water and is formed from the combination of two deuterium atoms and one atom of oxygen. Deuterium is a heavy hydrogen atom which has a nucleus of on e proton and one neutron. Hence, heavy water is a combination of heavy hydrogen and oxygen and is chemically known as deuterium oxide. It looks and tastes like ordinary water but it freezes at 3.8°C and boils at 101.4°C. The molecular weight of heavy water is 20 as compared to 18 for ordinary water; the density of heavy water is ten per cent greater than that of ordinary water.Although heavy water and ordinary water exhibit only small differences in their chemical and physical properties, there are large differences in their nuclear properties, the most important of which is the neutron moderating ratio, used to measure the ratio o f the slowing down power to the neutron capture characteristics. For heavy water the ratio is 21000 and for ordinary water it is 50. This high moderating ratio is essential for achieving a high neutron economy. Heavy water is, therefore, chosen as the moderating and heat transport fluid in the CANDU reactor."

Jan 1, 1983

By Sean McClenaghan

Significance Setting Size Production Value History of Discovery Zn and Pb at Austin Brook Brunswick Belt Exploration Discovery Hole Geology Structure Metal Zonation Directed Research Incremental Ores Precious metals Closure and Beyond Mining Remnants Tailings

May 1, 2013

By F. Roemer, D. Goldmann, T. Elwert

Tantalum is an important minor metal for the production of high performance capacitors. Approximately 60% of the annual tantalum production is used in this application. Despite its high price of 298 US$/kg (average price 2010–2014), at the moment, no recycling from end-of-life products takes place. In the established recycling processes of waste electrical and electronic equipment (WEEE), tantalum is lost in the slags of copper smelting, where it is highly diluted. An economic recovery is not possible at that point. Although tantalum must therefore be extracted from the WEEE stream before it enters smelting, no industrial recycling processes exist. The main reasons are its low concentration in the WEEE stream, lack of information about tantalum bearing devices, technical difficulties of extraction, and conflicts of interests regarding the recycling of other valuable metals in WEEE. In this paper, the results of a cooperation research project are presented. The aforementioned challenges are addressed and a novel tantalum recycling process is developed. Small pilot scale experiments show that a mechanical processing route can produce marketable tantalum-concentrates of 30% tantalum with yields between 60 and 70%. This is reached through a manual pre-sorting of potentially tantalum bearing products followed by a combination of an optimized comminution, sieving, air classifying, eddy-current (EC), and two stage magnetic separation. Key to the implementation of this process was a detailed survey of the tantalum concentrations in different products carried out by the industrial partner.

Jan 1, 2016

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By D. W. Smith, J. J. Koskinen, T. A. Enwald, M. E. Ball

"A full-scale demonstration unit of Tampella's LIFAC desulphurization process was tested at SaskPower's Poplar River Power Station Unit No. I. The test program included a series of parametric tests, followed by a 1500 hour operational evaluation. This paper summarizes the results of the test program, and SaskPower's economic evaluation which led to selection of the LlFAC process for SaskPower's 300 MW Shand power station. IntroductionOne of the major influences on the coal mining industry today is public and legislative response to acid rain. When sulphur-bearing fuels such as coal are burned, the sulphur oxidizes to sulphur dioxid e (S00 which, if uncontrolled, enters the atmosphere as one of the by-products of combustion. S02 then combines with water in the air to form an acid and acid rain results. Combustion also produces nitrogen oxides (N0J which can combine with water in the air forming nitrogen based acid , also contributing to acid rain.Acid rain has become a significant international concern. Newspapers have reported on dying forests, dead lakes and crumbling statues. Papers also include articles professing that the physical results of acid rain are vastly overstated. In the United States, a IO-year, Y2-billion dollar study called the National Acid Precipitation Assessment Program (NAPAP) was commissioned to evaluate the effects of acid rain. Even this extensive scientific study did not resolve the controversy. Despite disagreement over the quantitative effects of acid rain, there is no doubt that public concern over the issue is widespread and deeply felt.In response to this concern, legislators throughout the world have reacted with programs that restrict the emission s o f SO, and NO,. To industries involved in the supply and use of coal, the impact of these legislative programs has been extensive. United States power plants will be spending 10 billion dollars in the next decade for flue gas clean-up equipment. Even all this new equipment will not stem the tide of change to low sulphur coals and to “clean “natural gas. The following summarizes legislative actions taken for Canada and the United States."

Jan 1, 1993