Search Documents

By Hiwa Salimi, Foley. Stephen R, Loghman Moradi

Common water-miscible organic solvents including DMSO, DMF, methanol, ethanol, acetone and THF in combination with HCl and low concentrations of H2O2 were investigated for dissolution of gold. THF showed the best result demonstrating that gold powder could be completely dissolved in 1.5 hours in 1.0 mol/L HCl and 0.2 mol/L H2O2. No complete gold dissolution was observed for the rest of solvents even after 24 hours. The rate of gold dissolution was measured by dissolving gold wire in THF/HCl/H2O2 mixture. The rate of gold dissolution in optimised condition was 75 g m-2 h-1 at room temperature and significantly increased to 590 g m-2 h-1 by raising the temperature up to 60 oC. Although a THF/HCl/H2O2 mixture showed a slower dissolution rate in comparison with aqua regia, however the applied conditions are considerably milder which is highly promising for gold leaching in an industrial scale.

Jan 1, 2015

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By Steven Aiken

The East Boulder Mine located in Montana, U.S.A. utilizes snowmaking to assist with mine water treatment for nitrogen removal. Nitrogen species, including ammonia, are common contaminants in mine water from underground mining operations. Snowmaking provides secondary treatment of nitrogen during the winter due to the chemical and physical processes that occur during snowmaking, in the snow pack and in the snowmelt. The primary processes include atomization, evaporation, sublimation and volatilization. The snowmakers also provide secondary treatment for nitrogen removal when used as evaporators and/or land application units during the summer. In 2002, the snowmaking process was successful at reducing total nitrogen in the mine water by up to 87%. If additional losses due to soil and root zone processes are included, total nitrogen reduction would increase to between 87 and 97%. Snowmaking is an effective nitrogen reducing treatment method during the winter when other treatment methods such as land application cannot be used.

May 1, 2004

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By Tony Szwilski

Using Unity 3D as a collaborative multi-user virtual on-line environment, an interactive virtual underground mine platform (IVUMP) is being developed to provide on-line access to mine safety preparedness training with a focus on mine emergency response exercises (MEREs). Communication and information flow among MERE participants and their actions can be monitored, recorded and evaluated. A mine ventilation simulation utility VFIRE is being incorporated to enhance the realism and interactive nature of the ?in-world? exercises as well as extend its functionality to include training in real-time ventilation and fire control.

Aug 1, 2013

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By T. V. Simpkinson

Abstract A brief history of the electric arc furnace process of steel-making is given. The greater relative importance of this method of steel manufacture to the Canadian steel industry, as compared with its importance in the steel industry of the United States, is shown. The scope of the process is outlined and brief mention is made of the difficulty of obtaining melting stock low in alloy content. The physical chemistry of steel-making is discussed at length in simple terms, with emphasis on oxidation, de-oxidation, and the role of hydrogen. Carbide-type and silicon-type slags are described and the particular usefulness of each is outlined. The importance of various factors in the melting practice is evaluated on the basis of practical experience. Introduction Although electric furnace steels constitute only a small portion of the total weight of steel used in industrial operations, their importance is relatively much greater than is indicated by comparative tonnage figures. Tool steels, which are vital to all industry, are made almost exclusively by the basic electric arc furnace process, as are stainless steels, valve steels, and the higher alloy types of the class usually referred to as "alloy steels&apos;. For many applications where steel other than electric furnace quality is often used, and when first cost is secondary to performance in service, the extra steel cost of electric furnace quality material is usually returned with interest by consistently longer service life. The electric furnace is pre-eminent in the quality alloy steel field because of the control that may be exercised over conditions of oxidation, de-oxidation, and temperature, the fundamental operations in steel making.

Jan 1, 1948

By P. E. Fox, R. S. Cameron

"The QR gold deposit lies in the Cariboo plateau region of central British Columbia. The deposit was discovered in 1977 and since then a mineable reserve of 1.3 million tonnes grading 4.7 g/t Au has' been outlined in three separate zones. Soil sampling of glacial tills followed by diamond drilling of favourable host rocks proved to be key exploration techniques.The deposit is situated in the southern Quesnel terrane along the eastern fringe of the Intermontane Belt which here comprises a sequence of basic and intermediate volcanics and a series of stocks of alkaline affinity; generally diorite, monzonite and syenite. Hornfels and epidote-rich ferromagnesian exoskarn and sulphide-rich mantos have developed in a metamorphic aureole formed around a central diorite stock. Gold-rich zones lie along the outer periphery of the aureole where bodies of gold-bearing epidote-rich skarn and auriferous mantos rich in epidote and pyrite have formed in beds of calcareous tuffite lying at the top of a thick basaltic sequence. The deposit is regarded as' a subclass of gold skarn deposits. Diagnostic features are its association with alkalic intrusive rocks in a subvolcanic setting and the presence of oxidized, epidote-rich mineral assemblages.IntroductionThe QR gold deposit lies within the Cariboo plateau region of central British Columbia, 58 km southeast of Quesnel. The deposit, owned by Kinross Gold, was discovered during a regional reconnaissance program by Dome Exploration (Canada) Limited and Newconex Canadian Exploration in 1977. Considerable exploration and development has been done since that time. Mineable reserves of 1.3 million tonnes grading 4.7 g/t Au have been outlined to date in three zones."

Jan 1, 1995

By P. Chollet, A Constant

THE RESULTS of a previous investigation ( 1) on the work-softening of some heat-treated steels have led to the conclusion that the occurrence and intensity of the phenomenon is possibly governed by the work-hardening capacity of the material, and the relative amount of retained austenite. The first assumption is compatible with Polakowski's theory (2) that the absence of work-softening, in steels quenched and tempered at relatively low temperatures, may be attributed to the high rate of work-hardening which compensates for, and even out-weighs, the loss of internal energy associated with the simultaneous rearrangement of the original system of internal stresses. Indeed, Polakowski first considered the work-softening as a manifestation of a partial release (by cold-working) of the latent strain energy stored in

Jan 1, 1962

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management&apos;s beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By Eliodor Stoian

PRESSURE information has earned a place of recognition to almost everyone interested in oil and gas production. This interest is due chiefly to the multitude of uses to which it can be put. A sub-surface pressure test, conducted for as little as $60, may yield data worth many times its cost. To the uninformed, the testing techniques may seem complex. Fundamentally, however, they consist merely of the application of common sense. At one time, sub-surface pressure data were used only in identifying individual well problems and in finding appropriate solutions. Today, it is generally acknowledged that sub-surface pres-sure .data are essential for the proper evaluation and exploitation of oil and gas pools. The following is a review of significant applications of sub-surface data with regard to: (A).-Development (B) .-Completion and work-overs (C) .-Production (D) .-Reservoir engineering (E).-Proration (F) .Other applications of pressure data of a more general nature.

Jan 1, 1958

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco&apos;s concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By John A. Hansuld

Geochemical dispersion of metals under various environmental conditions is discussed within the frame-work of Eh (oxidation potential) and pH (acidity). In general, two aspects are considered -(1) the oxidation of certain primary sulphides in the outcrop or sub-outcrop environment, and (2) the movement of metals in different dispersion media. Practical applications of each are illustrated by means of exploration case histories representing environmental conditions in the Canadian Shield, the southwestern United States and the Caribbean.

Jan 1, 1966

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By Earl T. Hayes

This paper briefly reviews the laws enacted in the United States governing the coal miner. It discusses amendments to the Coal Mine Safety Act and describes the provisions of the Metal and Non-Metallic Mine Safety Act.

Jan 1, 1969

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972