Search Documents

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.  This is the result of the social and financial accountabilities that the industry is faced with because of the world’s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).  To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.  In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.  It follows that comminution is the major greenhouse gas emission process of the mine.  All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.  In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.  This paper makes a definitive contribution to that discussion.  The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.  Major emission contributors, steel, natural gas and electricity are discussed in detail.  The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.  The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.  Emerging steel making technologies are presented and discussed.  The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.  Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.  The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.  Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By Alan A. Barton

Introduction The Little Long Lac mine is situated in the Thunder Bay mining district, township of Errington, Ontario. The mine is located on the south side of the most westerly bay of Little Long Lac. The property consists of 36 claims, which comprise some 1,400 acres. This group of claims was staked in August, 1932, by Tony Oklend and Tom Johnson, and, after surface sampling, was optioned by the present controlling interests, who diamond-drilled it during the winter of 1932-33. In early spring, a small steam-driven plant was installed, and shaft sinking commenced on June 1st, 1933. During the summer, all supplies are transported to the mine from Hardrock station, at mileage 18 on the Canadian National Railway line from Longlac to Port Arthur. At Hardrock, which is seven miles from the mine, the railway skirts a bay of Little Long Lac, and supplies are loaded directly from railway cars to scows. Two scows are used, of 30-and 45-ton capacity, respectively. A 36-ft. pointer, powered by a 35 h.p. engine, is used as a tug. A good winter-road has been cut out from Geraldton to the mine, for winter transportation. Geraldton is about two miles north of the mine, and is also located on the Canadian National railway. A hard-surface road is now being constructed for summer as well as winter use. Geology The Little Long Lac gold area covers the northern limits of a large synclinal structure, the contact of the Keewatin flows and sediments, striking about twenty degrees north of west, with the dip of the sediments varying from eighty degrees north to seventy degrees south, the average being around eighty degrees south. The vein worked by Little Long Lac Gold Mines occurs in massive sedimentary rock of about the composition of arkosic or quartzitic greywacke, and consists of a shear-zone up to fifteen feet in width, striking N.75°E. and dipping steeply to the south, which has been filled by numerous narrow, parallel quartz veins and. veinlets. These are well mineralized. with arsenopyrite, pyrite, and some chalcopyrite and stibnite, and carry considerable quantities of visible gold. They show more than one age of quartz deposition, the quartz being fractured and re-cemented. The arkosic rocks separating the veins and veinlets are also slightly mineralized with pyrite. Work to date has indicated the probability that the vein-shear is controlled by local drag-folding.

Jan 1, 1935

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Troy Boisjoli

Since its discovery in February 2014, the Arrow Uranium Deposit has undergone rapid development through aggressive and systematic drilling programs and is now being progressed through advanced engineering and permitting. Based on the 2018 NI 43-101 Technical Report, the Probable Mineral Reserve estimate totals 234.1 million (“M”) pounds (“lbs”) triuranium octoxide (“U3O8”), contained in 3.43 M tonnes at an average grade of 3.09% U3O8. The proposed processing plant at the Rook I Project (the “Project”) will be capable of producing up to 31 M lbs of U3O8 per year, with a projected mine life of nine years based on the Probable Mineral Reserve estimate, although NexGen is permitting a 24-year operating life at the Project assuming the majority of Inferred Mineral Resources are upgraded to Indicated Mineral Resources with continued mineral resource development drilling. The Project will be developed through transverse and longitudinal longhole mining methods, pairing primary and secondary stoping techniques with a high degree of equipment mechanization which will provide a combination of good productivity, high extraction, and stable back support. This next generation of uranium operations combines the use of advanced tele-remote equipment and instrumentation with a low-cost bulk mining method and a best-in-class tailings management practice, effectively reducing operating costs and setting a new standard for elite environmental and social practices.

Jan 1, 2020

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By K. Harris, J. B. Wahl

Ni-base superalloy cast materials provide an outstanding balance of high temperature strength, fatigue resistance, oxidation resistance and coating performance and can be produced to very tight tolerances in extremely complex configurations, such as axial and centrifugal integral cast turbine wheels. As a result, cast superalloys are used in the most demanding applications of aero and industrial gas turbine engines. Use of these materials is expanding to smaller microturbine, turbojet, turbocharger and missile engine applications due to this unique combination of desirable properties. This paper will present an overview of the application of investment cast Ni-base superalloys and process capability to small turbine and missile engines.

Jan 1, 2010

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016