Search Documents

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

By J. R. Rodda

Stainless steels are widely used to handle concentrated sulphuric acid (H2SO4) solutions produced in the manufacturing process, The majority of corrosion rate data published for stainless steel in product acid conditions is typically complied in tables or in iso-corrosion diagrams (iso-corrosion rates plotted as a function of temperature and H2SO4 concentration), without any reported consideration as to the accuracy and relevance of the method used to obtain the data, Given the characteristic potential cycling associated with the active-passive corrosion behaviour exhibited by stainless steel in hot, concentrated H2SO4, weight loss is considered to be a more reliable method than electrochemical measurements to measure corrosion rates, Consequently, an effort is made herein to demonstrate the accuracy and relevance of weight loss to determine laboratory corrosion rates in product acid conditions.

Jan 1, 2010

By G. A. McGuffin

"IntroductionWITH the increase in quantity of sour gas reserves in the Province of Alberta, and the wider market for sulphur brought about by mounting world demand and restrictions placed on the principal supply, it was inevitable that this important source of sulphur would be .developed. In the light of these facts, it seems timely that a general paper on sulphur recovery from petroleum gases be presented. This, then, is the purpose of the following text. A short discussion of each of the following subjects is presented:(1) Properties and uses of sulphur(2) Existing sources(3) Market research(4) The recovery process in Turner Valley(5) Hazards of sulphur productionNo pretext of originality of material is made since innumerable reports have been prepared on this and related topics and information contained in these has been used quite liberally.Properties and uses of SulphurSulphur is a non-metallic element having an atomic weight of 32.06. The stable crystalline form at atmospheric temperature is referred to as 'rhombic' sulphur. It is bright yellow and has a specific gravity of 2.05, equivalent to 129.2 lb./cu. Ft. Above 204°F. sulphur has another stable crystalline form, referred to as 'monoclinic'. This is reddish-brown and is slightly less dense than the rhombic variety (122.4 lb./cu. Ft.). Sulphur in bulk form weighs 84 to 90 lb. per cu. Ft. Sulphur melts at approximately 240°F. to a straw coloured liquid which is quite viscous."

Jan 1, 1952

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By A. C. Elliott, A. J. Lafreniere

THE Hamilton Works of The Steel Company of Canada is a fully integrated steel plant with an annual capacity of three million tons. Located on the south shore of -Hamilton bay, it is in the centre of Hamilton's industrial belt. The heavy concentration of industrial activities found in this area, accompanied metallurgical well-known sources of pollution which are normal to urban areas is creating a pollution problem which concerns both industry and the general public. The Steel Company of Canada has recognized this problem and, accordingly, has adopted the policy of integrating suitable pollution control devices into its new installations. Much effort is also being expended to control the emissions of air contaminants from the existing equipment. At the Hamilton Works, there are two main sources of metallurgical dust emissions to the atmosphere -the Open Hearth furnaces and the Sinter Plant. Of these two, the Open Hearth furnaces are, undoubtedly, the largest single source of

Jan 1, 1962

"An unparalleled growth in the Canadian coal industry in 1970 coincided with increasing awareness by Canadians of their environment and their geography with its accompanying transportation factors. R and D on coal moved with greater emphasis toward solving problems in these areas as well as continuing with strong interest in coal preparation, carbonization, combustion, ""weathering'', spontaneous ignition, storage, exploration and geology. Long-range ""basic"" research was not forgotten in that work continued on coal-based carbons, coal chemistry and agrobiological uses for coal. This paper reviews the status of these many areas of coal research at the beginning of the seventies and takes note of some of the more significant legislation and projects brought to the author's attention. No attempt is made to itemize or to describe in detail all the worthwhile projects, many of which are reported elsewhere."

Jan 1, 1971

By Morris J. Viljoen, Young. David R.

"Abstract -The zone of economic interest at H.J . Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At !east three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5/Beatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more ·distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By D Maschemeyer

The cobalt production of the Chemical Metallurgical Division of Sherritt Gordon Mines Limited was supplemented, from May, 1962, to June, 1964, by processing 3,500 tons of a calcined cobalt-nickel concentrate. This paper describes the reduction roast -aqueous sulphuric acid leach process and the operating practices employed in recovering cobalt, nickel and copper from this oxidized by-product of a lead-copper operation. Incorporated in this paper is a description of how this process was integrated with the existing ammonia leach -hydrogen reduction process for the recovery of nickel and with the soluble cobaltic ammine process for the recovery of cobalt. Introduction T HE Chemical Metallurgical Division of Sherritt Gordon Mines Limited at Fort Saskatchewan, Alberta, has recently completed ten years of operation utilizing the ammonia leach process for the recovery of nickel, cobalt and copper from sulphide concentrates, matte and other materials amenable to this process. A continuing development program, along with the expansion of certain facilities, has enabled the refinery to attain a production rate of 31, 000,-000 pounds of nickel per year by hydrogen reduction. This represents an increase of approximately 85 per cent over the original design capacity of the plant.

Jan 1, 1965

By E. W. Mountjoy

THE Exshaw formation is a thin but very persistent black shale unit generally well exposed along the easterly scarp faces of the fault blocks comprising tl1e front ranges of the Rocky mountains. It is over lain by the Mississippian Banff shales and silty shales and underlain by the massive Palliser Limestone formation of late Devonian age. The Exshaw continues eastward under the plains of Alberta and on into Saskatchewan, with little change until it reaches the surface of the Palaeozoic-Mesozoic unconformity. During the summer of 1953, the writer was working- with a field party under Dr. J. L. Usher in the front ranges of the Alberta Rocky mountains. This party, sent out by the Mobiloil Company, conducted a geological survey of Devonian rocks between the towns of Banff and Jasper. The writer helped to describe and map these Devonian rocks and obtained first-hand information concerning the Exshaw shale and its relationship to the underlying and overlying sediments. Additional information was obtained from reference material and from a number of geologists whom the writer has consulted. Grateful acknowledgment is offered to them, to the Mobiloil Company for releasing field information, and to F. W. Beales and W. P. Hancock who helped edit the original paper for publication. Information from areas north and smith of that studied and from bore holes on the prairies is referred to. Localities mentioned may be found in Figure 1.

Jan 1, 1956

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

By K. Musgrave

"The ISO 9000 Quality Management System Standards have become internationally accepted as the way to manage quality assurance. The author has developed a Maintenance Management System Standard using ISO 9001as a model and is working with a major basemetal mining company to implement this. This paper describes the structure of the standard and the steps required for its implementation.Using a management standard ensures that a system is maintained, reviewed by internal audit, and when instances of failing to follow the procedures (nonconformances) occur, that corrective action is taken. It also ensures that regular reviews are made and that the sys-tem is continuously improved.The Standard is designed so that if an organization decides to register to an ISO 9000standard, the Maintenance Management System will be in a format that is compatible and can be incorporated with little effort into the Quality System.IntroductionIn reviewing maintenance operations at many mining companies, and often seeing those same organizations some years later, two recurring issues have been noticed..The first issue is how dependent effective maintenance is upon individual supervisors and crews. In one situation, a mine that had an excellent maintenance system in the 1980s. Now, with new supervisors and crews, it is starting to develop a system that will bring it back to where it once was. No written procedures remain from the earlier excellent system.The second issue is that most operations feel that maintenance is the sole responsibility of the maintenance supervisors and crews. Nothing could be further from the truth. Maintenance, like safety, is everyone’s responsibility. If the operator does not report problems and perform daily checks, and if the production supervisor runs equipment until it fails, then nothing the maintenance crew does will prevent emergency breakdowns and lost production. More importantly, equipment will be operated in unsafe conditions, putting employees at risk and, with today’s regulations, leaving supervisors open to prosecution.The Maintenance Management System outlined in this paper is designed to establish the present best practices as standard procedures, to provide a continual review so that these practices are improved in the future, and to identify instances where the system fails so that corrective action is taken. The mine referred to above is using this approach to make sure that, this time, the system it implements will survive."

Jan 1, 1997

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers' exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By L. Shasko

Deliberative mapping is a method of public engagement designed to bring citizens and specialists together to inform policy decisions in conflict-laden areas of science and technology (Stirling and Davies 2004a). Citizens and specialists participate in the process both separately and together. A deliberative mapping study was held in Regina, Saskatchewan in October and November of 2019. Participants in the study assessed options for reducing greenhouse gas emissions in small, remote or off-grid communities, including assessing the role of small modular nuclear reactors (SMRs) in climate change mitigation. Deliberative mapping is designed to facilitate direct, two-way conversations between citizens and specialists through both formal and informal discussions. The relationship building component of this process may increase trust. Public consultation processes that lack two-way dialogue or are seen as obligatory rather than meaningful can worsen public opposition or lead to negative public perceptions. Public education alone is not enough to change public opinion. Providing people with more information on topics they already hold opinions on can work to reaffirm previously held biases, but building relationships can provide new pathways to overcome divisions and turn close-mindedness into open-mindedness.

Jan 1, 2020