Search Documents

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Considerable improvements in diamond drilling equipment have been made since the early 1950s. A recent drilling programme, however, at Williamtown, near Newcastle, carried out by the Joint Coal Board on behalf of the Electricity Commission of New South Wales, emphasized deficiencies in existing equipment when particularly diflkult coring conditions were encountered.Spurred by unacceptably low recoveries in coal seams in this area, the Joint Coal Board devised and developed, with the assistance of the Electricitv Commission, a new typc core lifter and a special 26 ft triple tube core barrel, designed to operate in conjunction with it in bad coring conditions.The core lifter, whieh is propped open clear of incoming core during drilling, is activated by fluid impulses generated inside the core barrel. It can be used with double tube barrels when drilling firm rocks whichdo not change diameter by compaction inside the barrel.Softer rocks. such as clayey types, require the use of a rriple tube barrel.Results from testing carried out to date in difficult areas in New South Wales coalfields have shown that greatly improved results can be obtained with the new equipment. Although developed essentially for coaldrilling, the new core lifter and barrel could be adapted to other fields of diamond drilling. Even in areas where no great coring difficulty is encountered the cost advantage deriving from the greatly inereased life of the core lifter and the adaptor in which it is housed could justify its use.

Jan 1, 1967

Environmental information is an essential part of successful mine design and approval. In order to be most effective in its application and availability, this information needs to be collected in programmes with defined objectives and deadlines. Applied Geology Associates have established a methodology to facilitate the structured collection of environmental data, which provides for the diverse needs of both engineering design and applications for statutory and non-statutory approvals. Principal aspects of this methodology are the scope, timing and management of the environmental studies within the overall project planning framework.

Jan 1, 1987

By T J. Sprott, Associates

A number of people have expressed concern, understandably, that if mining operations take place in the Coromandel, the flows of mineralised ground water which exist will be intercepted. This water in many cases contains toxic metals including mercury, arsenic and lead and it is thought that if this water is allowed to enter streams or the waters of the Hauraki Gulf, it could endanger natural marine life and possibly established fisheries. This paper seeks to explain in simple terms the geology and the process of deposition of the various mineral deposits in the ground, the chemistry of the reactions between these minerals and the rain water falling on the ground, the hydrology and behaviour of this mineralised groundwater as it moves through the ground until it eventually enters the sea.

Jan 1, 1981

Grey River Gold Mining Limited (GRGML) has constructed and largely completed the commissioning of an alluvial gold dredge designed to recover gold from a low grade gold deposit in the Grey River Valley, New Zealand. The most important resource that GRGML has are the people who are employed by the organisation. The low grade of the deposit necessitates the requirement to operate the dredge at optimum efficiency, which in turn requires the work force to be of high calibre and continually motivated. The primary prerequisite for employment at GRGML is for employees to be receptive to new ideas and have the adaptability to develop new skills and apply those skills to the changing demands of the workplace.   A continually changing organisational structure is utilised to meet the needs of a changing work environment. The adoption of an innovative site employment agreement allowing for flexible working hours has aided the achievement of good employee productivity and attendance.   Employees gain a higher quality of life by working a roster pattern involving twelve hour shifts and a four day on, four day off pattern.   Employees and management are communicating very well and working together to achieve organisational goals which will ultimately benefit the employees, the shareholders, the local community and the mining industry generally.

Jan 1, 1989

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In formulating its strategic plan in 1998 the New Zealand Minerals Industry identified two related critical issues facing it. These are, broadly speaking, the issues of access to minerals; and the perception the public has towards the industry and its behaviour towards the environment. This presentation will report on the Industry's response to the public perception issue. The Industry has, through the NZMIA Council, and its Communication and Website Committees, developed and implemented strategies covering: communication through the print media, and through its website www.minerals.co.nz, a long-term educational outreach programme with schools, focussing on the significance of minerals, their contribution to community wellbeing and the negligible long-term environmental effects of the Industry's activities.

Jan 1, 2000

Similarities and Dissimilarities in Florida Phosphate Ore Types - Surface and Bulk Property Analysis of the Flotation Feed, Concentrate and Tails

Sep 13, 2010

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

Plant based on the New Jersey refluxing process was installed at the Cockle Creek Works of Sulphide Corporation Pty. Ltd. to refine portion of the zinc output from the Imperial Smelting furnace.Refining of impure zinc is effected by distillation in two stages in vertical columns comprising a series of superimposed silicon carbide trays designed such that ascending zinc vapours and descending liquid metal are in intimate contact. In the first stage, portion of the zinc and its cadmium content are distilled from impure feed metal, condensed, and while still molten, fed to the second column in which zinc is boiled under controlled refluxing conditions to remove the cadmium content.The resultant zinc has a purity in excess of 99·995 per cent zinc.The availability of refined zinc has made possible the production of a number of zinc alloys for marketing in addition to the basic grades of zinc.

Jan 1, 1970

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By D Craw, R Norris

The Golden Bar pit is part of the Macraes mine, the largest gold mine in New Zealand. The Macraes mine is mainly developed in the late metamorphic Hyde-Macraes Shear Zone. However, the Golden Bar pit was developed in a mineralised zone about 200 m structurally above the Hyde-Macraes Shear Zone. The host rocks are dominated by massive quartzofeldspathic schist (5 - 10 m layers) with minor intercalations (1 - 5 m scale) of micaceous schist. All the host schist has disseminated pyrite (micron to mm scale) from pervasive late metamorphic hydrothermal alteration.   In addition, there has been more localised (metre scale) relatively intense hydrothermal alteration controlled by shears subparallel to foliation. Gold occurs in three types of mineralised rock: silicified schist, which dominates, fissile black sheared rock, and cross-cutting quartz veins. There are three principal structural zones in the deposit: 1.   a strongly sheared micaceous and graphitic zone at the base of the structural sequence; 2.   a weakly deformed schist zone cut by relatively flat-lying (= 20¦ dipping) quartz veins; and 3.   a stack of imbricated schist pods and deformed silicified schist confined between two sub-parallel low-angle (ca. 30¦) shears.   These structural zones were juxtaposed during thrust deformation. The lower black shear zone has m-scale folding and over-thrusting packages, kink folding and foliation stacking with associated striations that imply west-directed thrusting. Striations and imbrication geometry between the upper two shears imply oblique thrusting that was directed towards the west. Post-mineralisation normal faults locally disrupt the mineralised zone. The Golden Bar pit mineralised zone has some of the structural and mineralogical characteristics of the main Hyde-Macraes Shear Zone, and may be genetically related.

Jan 1, 2006

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By Davies S. G, Mackey L. C

The oxidation of iron and nickel sulphide concentrates, and the dominant sulphide minerals which comprise them, has been studied under ignition conditions using thermogravimetry (fG). The concentrates were derived from various minesites and they showed differing tendencies to ignite. Ignition temperatures ranged from 416 to 488°C and the extents of reaction, measured at 500°C, varied from 64 to 88 percent. The reactivity of the least reactivematerial was improved significantly by grinding. Particles <63/lm showed 85 percent oxidation compared with 55 - 65 percent for particles >63/lm.Examination of the individual sulphide minerals revealed that these materials also have significantly different degrees ofreactivity and are subject to particle size effects. For particles <45/lm, the ignition temperatures were as follows:ò pyrite and violarite 380 - 385°C; pentlandite 425 - 430°C; and pyrrhotite 470 - 475°;ò for particles >90 /lm, the ignition values were: pyrite 395 - 400°C;ò violarite 430 - 435°C; pyrrhotite 540 - 545°C; and pentlandite 560 - 565°C.Using the data on the individual minerals it was possible to rationalise the differing degrees of reactivity of the concentrates. The role of the most reactive constituent in initiating the ignition reaction has also been discussed.Finally, the results of this work were found to compare. favourably with the behaviour ofthe concentrates in industrial and pilot-scale flash smelters.

Jan 1, 1989

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

Mine ore, reduced to minus 71/2 in. by primary crushers, is stockpiled. Size reduction of the reclaimed material by secondary and tertiary crushers is achieved in a closed circuit crushing and screening plant. Screen products of minus 30 mm plus 6 mm lump, and minus 6 mm fines are stockpiled by conveyor and stacker systems prior to rail despatch 10 port facilities at Dampier. Crusher settings, determined from experience, are closely maintained to obtain the desired lump/fines ratio. Chemical and sizing analyses from automatically taken samples are used to maintain product specifications. The beneficiation plant upgrades the fines product when this is necessary. The recorded wear life of individual plant components is the basis of a planned maintenance programme.

Jan 1, 1970

An Evaluation of Froth Recovery Measurement Techniques

Sep 13, 2010

Talvivaara deposits, Kuusilampi and Kolmisoppi, comprise one of the largest sulfide nickel resources in the world with 642 Mt in Measured and Indicated Resource categories. TalvivaaraÆs preferred extraction technology is bioheapleaching, which is already widely used for other metals, notably copper and gold. The company has demonstrated the viability of bioheapleaching technology for the extraction of nickel using the Talvivaara ore. The leaching process is heat generating and therefore suitable for the subarctic climatic conditions. The planned annual metal production is 33 000 t of nickel, 60 000 t of zinc, 10 000 t of copper and 1200 t of cobalt. Talvivaara deposits are well-suited for open pit mining due to a thin overburden, favourable resource geometry and a low waste to ore ratio. The ore is relatively low-grade, but well suited to bioheapleaching due to its high sulfide content. Bioheapleaching is a process whereby metals are leached from ore as a result of bacterial action. The bacteria used in the Talvivaara bioheapleaching process are endemic to the area and therefore well adjusted to the prevailing environmental conditions. The solution is collected at the bottom of the heaps and either re-circulated through the heap or fed to metal recovery. In metal recovery, nickel, copper, zinc and cobalt are precipitated from the pregnant leach solution and filtered to produce saleable metal products. After the metals are removed, the solution is further purified and returned to irrigate the heaps. Mining, bioheapleaching and metal recovery techniques for the Talvivaara mine have been tested in a 17 000 t on-site demonstration trial during 2005 and 2006. Subsequent construction of the mine started in 2007 and commercial production in the fourth quarter of 2008.

Jan 1, 2009

The Mineralogy and Reactivity of Pyrrhotite from Selected Nickel Ore Deposits and its Effect on Flotation Performance

Sep 13, 2010