Search Documents

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992

Western Mining Corporation (W.M.C.) operates a nickel refinery at Kwinana, 30 km south of Perth. The refinery commenced pro- duction in May 1970, with a rated capacity of 15 000 tpa of nickel metal. A hydrometallurgical route was chosen as the most expedient way to produce nickel metal at a time when world demand for nickel was outstripping the supply. Later events dictated that an increase in production from the refinery be achieved. To this end, matte produced from Kalgoorlie Nickel Smelter, which was commissioned in 1972, was used in varying proportions as a complement to the concentrate initially utilised as input to the refinery. The effect of matte addition was to increase the capacity to 30 000 tonnes of nickel per annum. This was accompanied by other benefits which were 1. reduction in energy consumption per unit of nickel produced, 2. improved metal extraction, 3. improved precious metal recovery, 4. reduced production of ammonium sulphate by-product. Refinery operating results for the years 1970 to 1983 show how matte feed has improved refinery performance in these areas.

Jan 1, 1984

By Plyley WF

Kidston Gold Mine is a 3.5 million tonnes per year operation located 280 kilometres west of Townsville, Queensland. Kidston's ore body consists of 44.3 million tonnes graded at 1.79 grams per tonne gold and 2.22 grams per tonne silver. Full production commenced in March, 1985. During the remainder of 1985, Kidston milled 3.77 million tonnes of ore and produced 213,614 ounces of gold.The ore is comprised of granodiorite, polymictic and volcanic breccias. The degree of oxidation of the rock influences the milling capacity and therefore determines the cut-off grade; ore is categorised as oxide, transition and fresh. The milling rates are 15,400, 12,000 and 9,600 tonnes per day for oxide, transition and fresh ore respectively.The ore is treated in a conventional cyanidation/ carbon-in-pulp plant (CIP). The plant consists of a primary crusher, semi-autogenous grinding (SAG) and ball mills, leach circuit and carbon-in-pulp circuit. Carbon stripping and dore smelting are done on site. The major difference between the Kidston plant and other Australian CIP plants is that a cyclone separation and washing circuit rejects half of the dry tonnage as a sand tail prior to CIP treatment. This difference allows the CIP circuit at Ki.dston to be smaller and makes the CIP less sensitive to the grind circuit product size.

Jan 1, 1986

Development of a small ore body to 137m below surface was carried out in sixteen months driving 610m of 1:5 decline.

Jan 1, 1973

By N Javati, G D. Carman, D Kikiha, B Likia, K Dala, J McPhie, R Johnstone, D R. Cooke, J L. Blackwell

The 40 Moz Ladolam gold deposit on Lihir Island, Papua New Guinea is the worldÆs largest, low-sulfidation, epithermal gold deposit, in terms of contained gold. The deposit has average grades of 2.42 g/t Au (LGL Resources Reserves Update, 2008) and gold is hosted primarily in refractory pyrite. Lihir Island is part of the 150 km long, Tabar-Lihir-Tanga-Feni, alkalic, volcanic island chain located in the New Ireland basin. Five volcanic blocks comprise Lihir; Plio-Pliestocene Huniho, Kinami and Luise volcanic edifices are built on top of remnant Pleistocene Wurtol Wedge and Londolovit Block (Wallace et al, 1983). The Ladolam gold deposit is located in the central portion of the dissected Luise volcanic edifice and is composed of four main orebodies: 1. Minifie, 2. Lienetz, 3. Coastal, and 4. Kapit. An active geothermal system is overprinted on the ore deposit, localised along north-trending lineaments, and is expressed as hot mud pools and fumaroles. The focus of open pit mapping and drill core logging, as part of ongoing PhD research, has been in the Minifie and Lienetz orebodies. The deposit geology is grouped into four main phases: 1. volcano-sedimentary host rocks, 2. porphyry-style biotite alteration and related hydrothermal breccias and veins, 3. epithermal-style breccias and veins, and 4. modern geothermal alteration. Gold is associated with epithermal-style alteration and mineralisation. Ongoing observations of the Minifie and Lienetz orebodies are highlighting differences in the geology and paragenetic histories. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Phipps P. J

The rate of precipitation of ferric iron as ammonium jarosite, NH4.Fe3(SO4)2(0H)6 from acidic solutions near 100¦C, was found to increase with weight of jarosite seed crystals, and with concentration of ammonium ion, but to decrease with increasing acidity. The particle size of the product crystals was larger at low sulphate concentrations and at high ammonium concentrations. Particles appeared to be agglomerates, with diameters ranging from 0.5 up to 25 um, and composed of individual crystals of diameters ranging from 2 um apparently down to 0.1 um or Lass

Jan 1, 1977

By Svenson D

For fully effective information to be obtained from exploratory drilling for coal, drilling programs should be planned systemati- cally in successive stages, on the basis of existing geological criteria and information collated during each stage. In this way, drilling can be executed with optimum economy, aided by auxiliary geophysical techniques wherever these may be appropriate. The object- ives of the programs must ultimately include an adequate assessment of mining conditions as well as thorough evaluation of coal quality. The first of these objectives is not always appreciated by both geologists and mining engineers engaged in supervising drilling pro- grams, often resulting in the need for more additional drilling and more expense than would otherwise be required. To achieve all of these objectives as effectively as possible, the drilling should be supervised by well qualified personnel experienced in working in a multi- dicipline, professional mining, geological and engineering team.

Jan 1, 1977

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

Investigation on Sheelite Floatability by Particle Size Fraction

Sep 13, 2010

By Smith R. N

The Olympic Dam copper-uranium-gold-silver deposit is located approximately 520km north-northwest of Adelaide, South Australia. The deposit was discovered in 1975 by the Exploration Division of Western Mining Corporation (WMC). A joint venture, to facilitate development of the deposit was formed in mid 1979 between WMC (51%) and the British Petroleum Group (BP) (49%).

Jan 1, 1990

By S Thomas, E Grimsey

Mining education in Australia has undergone another cyclical downturn over the past five years and several departments have been discontinued while others are still teetering on the brink of destruction. During this downturn Curtin UniversityÆs WA School of Mines (WASM) has managed to stay alive and well, but this has not been by accident. This paper outlines some of the strategies and experiences that have kept WASM in a strong position and offers hope to other departments and schools elsewhere that are still experiencing difficulty. This paper is also directed at all mining departments and schools that are certainly going to see it all happen again after the next mining boom turns to bust.

Jan 1, 2004

The difference between a hypothetical and a theoretical approach is considered and the advantages in using a hypothesis is discussed. Virgin horizontal stresses play an important role in stabilising strata which bridge across an excavation, and reduces the tensile stresses which develop in a beam subjected to bending. Simple formulae are deduced for the bridging of a thick massive stratum under such conditions. At shallow depths, tensile failure on the upper side of the beam is the most likely cause of fracture, but below a certain depth this gives place to compressive failure on the underside, with the possible incidence of rock bumps. The presence of strong massive beds delay the onset of subsidence and may restrict the width of the subsidence trough. If the material involved in the caving is strong, this will reduce the final subsidence, especially at shallow depths. The British regulations for the control of aquifers and their dependence on the strain developed at the seabed are discussed. As an alternative, the concept of a disturbance factor is introduced to permit the consider- ation of aquifers at depth, leading to an explanation of the make of water on the first faces to be mined in the Selby Coalfield. 'Elie paper closes with a brief consideration of the different roles played by longwall face supports in the control of readily cavable strata, and the control of strong beds which hold up in the waste.

Jan 1, 1986

By Smith PE

The main components of face design are the power loader, face conveyor and powered support system and the interaction of these components determines the effectiveness of strata control. A major influence upon the interrelationship of this equipment is the geological environment, of which seam thickness appears to play an important role. Recent thick seam experience indicates a significantly different characteristic behaviour pattern from that observed in thin seams The structural integrity of the face wall is particularly influenced by seam discontinuities such as natural joint planes and mining-induced fractures in the yield zone ahead of the faceline. In addition, the presence of stone bands or dirt partings in the seam offers interfaces for uncontrolled release of blocky material. Some case study experience at British collieries provides a comparison with performance data at a specific location, that highlights the importance of coal face layout and design.

Jan 1, 1986

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By Wardle L, Wright G

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modem houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various' house designs.

Jan 1, 1992

This paper describes the mechanical and electrical maintenance activities as practised at Isa Mine. The principles of preventative maintenance adopted are described as well as the basis of maintenance cost control.

Jan 1, 1978

By Tran T, Young D

During the processing of gold, effluents that are discharged into the tailing dams contain free cyanide, metal cyanide complexes of zinc, copper, iron, etc and their oxidised products such as ammonia, cyanate and thiocyanate. A knowledge of how different cyanides behave in the solution is vital to metallurgists working in the area of cyanide waste treatment. Although the free cyanide ion is not stable in aqueous solutions and is expected to degrade in a natural environment by atmospheric oxidation, the metal cyanide complexes, especially of iron, are very stable. The CHEMIX program from the THERMODATA package, developed by the CSIRO Division of Mineral Products, was used to evaluate various copper-cyanide and iron-cyanide systems. The simulation of these systems show how the free cyanide and cyanide complexes behave at different conditions of solution composition and acidity (pH).

Jan 1, 1991