Search Documents

By McBride N

Location The Boddington Gold Mine (BGM) is located approximately 120 km south east of Perth, Western Australia. (Figure 1). Located within the picturesque Darling Ranges, the land was previously used for forestry activities prior to mining commencing in mid-1987. Mineralisation is hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt.

Jan 1, 1995

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

In line with the recommendations of The AusIMM/AMIC Joint Committee Report in 1981 Isa Mine ore reserves are quoted in proven and probable categories (recoverable ore reserves). Internal reporting considers geological mining and extraction reserves in terms of proven and probable categories. Proven reserves are subdivided into detailed and confirmed ore. External reporting includes a possible ore category (not a reserve). The basis for these divisions is the spatial distribution of sampling data. Proven ore is defined by data 80m apart or less and probable ore by data 80m to 150m apart. Within the proven ore category detailed ore is defined by data 40m apart or less and confirmed ore by data 40m to 80m apart. Kriging is used to provide tonnage and grade information for the currently producing 1100 and 1900 orebodies. Kriged cross sections are initially produced to coincide with existing geological sections and are used for stope design. Stope ore reserves calculations are ideally performed at three discrete design stages, which in order of increasing accuracy are: preliminary design (PD), final design (FD) and ring design (RD). At each of these stages Kriged meshes incorporating the most recent sampling information are produced for reserve calculations. Historically derived mining and extraction factors are applied both to global reserves and individual stope reserves to reflect changes in geological and mining conditions as well as the sequencing of extraction. These factorised reserves are then inserted into the computerised reserves inventory system (RIN). Monitoring of individual stope performance continues into the production stage with input from planning, research, survey and production personnel. This allows actual extraction factors to be derived for comparison with predicted factors, providing some measure of stope performance.

Jan 1, 1987

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008

By Bromley JC

Eimco Great Britain, a division of Baker Mining Equipment Company, was contracted to develop a hardrock tunnelling machine in conjunction with British Coal. The objective: a machine to cut rock up to 170 MPa compressive strength yet retaining the flexibility of roadheader type machines. This flexibility to encompass mobility, wide range of excavation shapes and sizes, simplicity of design and use, compact size, and efficient cutting operation. Current roadheaders operating in hard material are characterized by: 1. Severe machine vibration 2. Bouncing of the boom away from the rock 3. Very high pick wear 4. Inability to sump head in bad floor conditions The reasons for this poor performance can be attributed in part to: 1. High speed of cutting head rotation 2. Inability to hold boom against rock while cutting variable hardness strata. To overcome the problems described, a new articulation method was developed utilizing four hydraulic rams to "lock" the boom in position on one axis and four hydraulic motors to rotate the boom for cutting via a turret arrangement. The slide mounted turret is hydraulically advanced for sumping into the face, independent of the machine base. To transfer cutting forces back to the rock, the machine base is held rigidly in the excavation by floor to roof or side to side rams. A cutting head mounted on the boom rotates at very low speed, but with very high torque.

Jan 1, 1987

By Andersson PO

Boliden Mineral AB Boliden Mineral AB operates nine mines in Northern and Central Sweden, producing zinc, lead and silver concentrates and copper and gold. Seven of these mines use cut and fill (C&F) mining with a total production of 2 Mtonnes of ore per year.

Jan 1, 1998

By Kilgour I

The installation of a final cleaning column at Ok Tedi Mining Limited was carried out to increase final concentrate grade in order to reduce concentrate handling, shipping and treatment charges and to reduce penalty payments. To fast-track the project a decision was made to install a full-size column on one of the two parallel circuits, designed on information readily available and utilising the experience of mill staff and an engineering consultant, rather than delay installation while a pilot scale program was conducted. A 3.66 m diameter by 12.8 m high column was installed to produce 40 t/h of final concentrate from a combination of rougher concentrate and recleaner concentrate. The column design and sparger system were by Cominco Engineering Services Limited.

Jan 1, 1991

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

By Yaroshenko YuG, Bokovikov BA, Gordon YaM

Problems of the effect of the number of tuyeres and their parameters on the uni- formity of gas distribution are invest- igated with the use of the authors' devel- oped mathematical model of the movement of gases and materials in the blast furnace. It is shown that the improvement of uni- formity of gas distribution with an increase in the number of tuyeres has a damping character. An analysis of the errors of the specified assumptions of the hypothesis concerning the potentiality of the gas movement in the bed is carried out. It is established that the potential approach model gives good results with the determination of the discharge of gas and its stress field, but is not useful for the calculation of local velocities of gas in the raceway. The results of trials of calculation investigations of the dynamics of form- ation of the raceway and the voidageòfield in beds of burden materials are presented in the concluding part of the paper.

Jan 1, 1981

The Engineering Chemistry Division of the Government Chemical Laboratories of WA initiated an ongoing investigation into the possible utilisation of diatomites of this State. The work has shown that local diatomites can be beneficiated by hydro or pneumatic cyc- lone separator circuitry and that the better quality head materials can be upgraded by straight and flux calcination and associated processing to the equivalent of premium grade imported products. Western Australian diatomites vary con- siderably in quality, and the degree to which they can be upgraded and the yield of useful product are influenced by the proportion of impurities and the size, type, and degree of fragmentation of contained diatoms. Conseq- uently careful assessment of ore deposits will be necessary in order to relate ore reserves to planned production. The viability of commercial production from Western Australian resources would hinge on the establishment of markets - largely ex- port - capable of supporting a production level of the order of 30,000 tonnes per annum.

Jan 1, 1979

Whereas traditionally, stable isotope research has been directed towards resource exploration and development, it is finding more frequentapplications in helping to assess the impacts of resource utilization upon ecosystems. Among the many pursuits, two themes are evident:(1) tracing the transport and conversions of pollutants in the environment and(2) better understanding of the interplay among environmental receptors, e.g. food web studies. Stable isotope data are used primarily to identify the presence of pollutants in the environment and with a few exceptions, the consequence of their presence must be assessed by other techniques. Increasing attention has been given to the isotopic composition of humans with many potential applications in areas such as paleodiets, medicine, and criminology. In this brief overview examples are used from the Pacific Rim to illustrate the above concepts. Stable isotope data will undoubtedly play an increasing role in multi-disciplinary research in the Pacific Rim. However, consideration should be given to more effective strategies, e.g. networking, for pursuing large scale problems such as long range circulation of pollutants.

Jan 1, 1990

Before the arrival of the first Europeans, Aborigines living in the northern Flinders Ranges mined ochre - an earthy form of haematite used for pigment.The discovery of copper ore at Kapunda and Burra in the 1840s stimulated the early settlers to prospect further north along the ranges. Many of the new discoveries were not properly evaluated and companies were floated on the most tenuous evidence.

Jan 1, 1993

By P O. Andersson

Mining of sill pillars is more difficult than the ordinary mining. The sill pillar mining is performed under more difficult conditions and the mining of the sill pillar itself produces more problems; failure of the rock due to high stresses, difficulties in controlling the fill above, overall stability of the stope and special requirements on the technique for backfilling. Altogether this makes sill pillar mining technically difficult and often not profitable. A project was therefore initiated with the aim to increase the mineable ore reserve by making sill pillars mineable, both technically and economically. The project aimed at developing technique for already existing sill pillars as well as planned sill pillars. For the existing sill pillars a technique would have to be developed for mining beneath unstabilised fill. For sill pillars that would be created in the future, the most suitable mining method and methods of supporting or stabilising the fill in the stope above was to be chosen within the project.

Jan 1, 1998

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

Battle Mountain Gold Company's Paj ingo Mine is the first gold mine developed by the Company in Australia. The Mine located in northern Queensland commenced operations in September 1987. The high grade epithermal orebody is selectively mined and processed through a conventional carbon in leach/carbon in pulp (CIL/CIP) plant at a rate of 200000 tonnes per annum. In 1988 it produced 61000 oz gold and 152000 oz silver. Inadequate preoperational development of non technical management and organisational functions often leads to inefficiencies that last well into the operation. The Pajingo experience in this regard is oaTple ented by those from a number of other recently commissioned small operations. A checklist is discussed to assist any future preoperational group in focussing their attention into areas that seem to be of secondary importance at the time but often have a significant impact on overall management efficiency later.

Jan 1, 1989

As this district is so far distant from the other mining centres and its mode of approach so circuitous, I am afraid that many residents of other portions of the Commonwealth never think of paying this" Australia's Silver City" a visit, to learn personally the many and various lessons everywhere available, and to become familiar with the really wonderful and interesting features and deposits (which pature has so lavishly bestowed in the mineralogical world) yet seemed to almost ignore or overlook when disposing of topogr,aphical beauties of landscape and vegetation) unless professional or business duties require their presence here. So it is to those whose life is necessarily spent in other parts of the States where they answer their call of duty, and yet feel an interest, either for business or other reasons, that my paper is specially addressed and prepared, and for that reason I witl endeavour to make my remarks more of an explanatory than a dictatorial nature. I feel sure that there. are many members of our Institute who are much more familiar, and have had many more years' experience in the various methods of timbering, filling, and ore extraction, etc., than myself, but I hope that over I6 years' experience in connection with mines and engineering works, the last six of which have been spent in Broken Hill, where, I have been very closely connected.

Jan 1, 1903

By Murphy MW, Klaric SD

The history, operation and design of the Secor continuous rod production process is described. The effective operation of the plant is influenced by accurate monitoring and control of molten metal properties, mould release application, coolant application and composition and correct setting of all operating parameters. The continuity of operations, which is an essential feature of this type of plant, is also greatly influenced by the service life of wear parts in the operation. This paper deals with three principal wear parts which come into direct contact with copper during operation, these are:

Jan 1, 1985

All aspects of the development of Ulan Coal Mines are covered - from a small pit pony mine in 1975 to an efficient mechanised underground and open cut operation today.

Jan 1, 1983

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983