Search Documents

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

Daily geological mapping of the Panguna porphyry copper/gold system since mining began in 1971 has provided a good basis for resource estimation and mine planning as the mine and estimation methods have advanced. Geology defined during evaluation and early mining has been substantiated and many smaller features have been better defined or identified. Breccias, pebble dykes, major structures and location of lithology contacts important to short term planning and long term pit slope stability have been defined. Correlation of copper and gold with breccia zones is quite striking and was not fully appre- ciated at the end of evaluation. Pit mapping geology, and diamond drill geology and assays, are now routinely added to a Geological Data base on computer, which forms the major geological data base for modelling the deposit. Geology from diamond drill logging, updated by pit mapping, and assays from diamond drilling updated by blast hole assays have been incorporated in a 45 bench deep 486 000 block computer based block model which forms the basis for long and short term planning. The introduction of pre-concentration scre- ening, based on the distribution of mineralisat- ion and fracturing, puts more emphasis on the definition of grade distribution at low concent- ration and on structures in the rock. Geostatistics is now used for resource estimation and has produced acceptable estim- ates. but these need to be refined, particularly in peripheral, low grade areas of the deposit.

Jan 1, 1987

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

By Durucan S

The southern Attiki peninsula is a very interesting area from an environmental point of view. The port and the city of Lavrio is situated at the east coast of the peninsula with about 10 000 inhabitants and there are also a few villages in the vicinity. The south-eastern part of the peninsula hosts the famous Lavrio mines which exploited the silver bearing orebodies of the area for more than 25 centuries. As a result, soils around the city of Lavrio are polluted with high heavy metal loads. The area is also of archaeological interest, as there are well preserved remnants of ancient mining and processing plants and archaeological sites. Soil samples collected from an area of approximately 120 km2 around Lavrio were analysed for their metal contents and the spatial distribution of the concentrations of ten selected elements were estimated from these data sets. The spatial data analysis and transformation capabilities of Geographic Information Systems, combined with extensive mining and geological data, helped the authors to identify the extent and causes of metal pollution around Lavrio.

Jan 1, 1995

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

By P A. Gow, J L. Walshe, G J. Masterman

The Eocene-Oligocene porphyry belt of northern Chile contains the worldÆs largest accumulation of porphyry-related copper metal. Conflicting models exist regarding the relative importance of strike-slip and reverse faulting during the emplacement of the porphyry and epithermal systems, based on regional studies and also from work at the Chuquicamata deposit. In contrast, at the Collahuasi district, high sulfidation state copper-silver mineralisation was superimposed into the core of the Rosario copper-molybdenum porphyry deposits along normal faults during gravitational collapse of the Domeyko Cordillera. Exhumation of the porphyry environment occurred rapidly during this event, allowing near-surface epithermal mineralisation (<200 m paleodepth) to be juxtaposed into the potassic altered core of the porphyry deposit (estimated depth of formation: 1300 m) in the space of approximately one million years. Mass wasting after major episodes of tectonic uplift provides an effective method of hypogene upgrading of porphyry ores by high sulfidation mineralisation.

Jan 1, 2005

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

This paper presents a new idea in field data collection for geological and scientific data. The computer keyboard has been replaced by a barcode wand driving a spreadsheet style editor. To use the full capabilities of computer hardware currently available, geotechnical and geological data can be entered and validated in the field, in a structured format, for later transfer into modem geological modelling databases. An example, using a geotechnical borehole log, explains the principles discussed. The generic nature of the Datcol system is illustrated by the application developed using the Norwegian Geotechnical Institute Rock Mass Classification system. A brief description of a modem spatial relational database is also given with particular reference to underground engineering.

Jan 1, 1993

Recovery of tin and copper from concen trates containing cassiterite, stannite and chalcopyrite was studied in laboratory-scale tests designed to simulate continuous operation of the matte fuming process in which tin is recovered as SnS fume while copper accumulates in the matte. Charges made up of 300g of mixtures of the concentrate and siliceous flux were added at a uniform rate in pelletized form to crucibles containing 300g of matte and 50g of slag (both of which were recovered from previous tests), while blowing through the matte with air or oxygen-nitrogen mixtures at a rate of 3 to 5 1/min. Accurate material balances enabled the effects of process operating conditions on tin recovery and sulfur utilization to be deter- mined. When operated correctly, the matte fuming process gave tin recoveries exceeding 90 percent in spite of wide variations in the copper content of the matte and in the operat- ing conditions. Deterioration of tin recovery was associated with undersaturation of the slag with respect to silica, and with high partial pressure of sulfur dioxide (greater than approx- imately 0.2) brought about by oxygen enrichment of the blowing air. The utilization of sulfur varied widely in low grade mattes. Copper in excess of approx- imately 10% promoted formation of SO2 by the commonly accepted reaction: FeS + 1-120 2= FeO + S02 while in copper-free and lower grade mattes a substantial fraction of the oxygen was consumed in the alternative reaction FeS + i 02 = FeO + z S2.

Jan 1, 1980

By M D. Goodz, Wright R. F

This paper highlights the importance of accurate observational technical reports compiled by Mining Geologists and Engineers. Before uncovering the original reports in July 1992, all previous investigations discounted returning to old mining areas on the belief that all operations were suspended because they were 'unpayable'. However, the detail of the original reports removed any doubt of the economic value of retrieving remnant ore.The important feature was that the description of 'unpayable' by GMA could be equated to 11.6 - 35 g/t over the history of the mine. On the basis of these reports the Morning Star mine has been re-opened.

Jan 1, 1993

The Golden Plateau Mine is located at Cracow in central Queensland, 350 kilometres north west of Brisbane. The mine was operated by Golden Plateau NL as an underground mine from 1933 to 1976 with a total production of 18.5 tonnes of gold. Prod

Jan 1, 1994

By Peters S. G, Beams S. D

CONCEPTS AND REGIONAL GEOLOGY The Charters Towers region holds many keys to the metallogeny associated with the complex geological development of eastern Australia during the Palaeozoic. Tectonic, magmatic and volcano-sedimentary depositional episodes can be identified and related to the chronological development of batholithic host rocks (Clarke & Paine, 1970; Henderson, 1986; Murray, 1986). Pre-batholithic basement rocks in the north (Charters Towers Metamorphics) consist of a package of amphibolite grade schists interlayered with and intruded by gabbros and diorites (Peters, 1987). To the south (Seventy Mile Range Group) greenschist facies Cambro-Ordovician rocks overly some of the basement. The lower age of this basement is not constrained, parts of it could be as old as Pre-Cambrian. Mid-Ordovician (approx. 470 my) to Lower Devonian (approx. 400 my) age I-Type granitoid plutons of the composite Ravenswood batholith intrude the pre-batholith basement and the Seventy Mile Range Group. Igneous activity was initiated again in the Carboniferous with the extrusion of rhyolitic lavas and pyroclastics associated with porphyry and high-level intrusive complexes (Wyatt et al., 1971). The Ravenswood block is bounded by Devonian and Tertiary sedimentary sequences of mainly continental provenence.

Jan 1, 1989

By Erceg MM

The Waft River gold deposit is hosted by low grade metasediments which have been intruded by a dacite/andesite porphyry complex. Wafi River is classified as a high sulphur, epithermal type gold deposit having: a high sulphur content, a close association with calc-alkalic igneous rocks, zoned advanced argillic and argillic alteration, and enargite group minerals. Gold occurs as minute inclusions in pyrite and pyrrhotite within intermediate dickite/kaohnite - interlayered illitic clay alteration zones. Central leached silicic, alunite and pyrophyllite zones and peripheral chloritic zones are low in gold. The gold mineralisation at Wafi is interpreted to have been predominantly caused by mixing of hot upwelling acidic magmatic mineralised fluids with cool, neutral meteoric/hydrothermal fluids within permeable sediments. Locallised high grade breccia zones are encountered within the porphyry. An initial resource in excess of I million ounces Au has been defined.

Jan 1, 1990

The moisture content of clean coal contributes significantly to the product's transportation costs, handleability characteristics and/or energy value. A major contributor to the total moisture is the ever increasing proportion of fine coal in

Jan 1, 1994

By Bedford D. J

The post pillar cut and fill stoping method has been adopted by King Island Scheelite for the extraction of the main Dolphin orebody. The orebody is a massive, tabular deposit varying from 10 to 50 metres in thickness, and dipping at approximately 30¦ towards and under the sea bed. The mining method was selected for 1. maintenance of hangingwall support under the sea bed; 2. maximisation of first stage ore extraction; 3. flexibility of mining, allowing maintenance of grade and selective mining around waste bands within the orebody, and 4. compatibility of existing equipment both with stoping and the on-going underground mine development programme. Stope parameters were established on the basis of initial rock stress analyses, and since the undercut phase of mining the stoping programme has been monitored with various types of deformation measuring devices installed in a series of large diameter boreholes.

Jan 1, 1977

By Hall J. S, Zuiderwyk M, Reid A. F

A prototype version of a computer controll- ed on-line scanning electron microscope image analyser, employing the real-time signals ob tamed by digital control of the electron beam has been used to obtain statistical quantificat lion of a wide range of mineral grain character istics, including composition, size distribut- ion, and degree of liberation. These propert lies have been determined for suites of whole particles of flotation concentrates, mounted without further preparation. The facility is also well adapted to the measurement of general Istereological parameters. The computer control software is based on an operating system which includes the device drivers and which is linked to FORTRAN programs [containing the procedural algorithms. The beam scanner provides a 4000 x 4000 point raster swept at a 10 Mhz rate in steps of 1 to 200 points and a set of up to 8 signal channels which respond to electron or energy dispersive X-ray signals to provide a digital attern.characterizing the sample composition. the beam is stepped at high speed until a part- 'cle or phase boundary is encountered; a longer well time is set if X-ray data is required. he digital scanner interrupts the computer

Jan 1, 1977