Search Documents

By S Hayton

While coal seam gas is considered to be an unconventional gas, the proliferation of areas under exploration and development mean that it is rapidly becoming main stream. The potential of New Zealand's coals to produce coal seam gas has been recognised for some time. However, key market drivers have not been suitable for the progression of this potential into reality. Kenham Holdings Ltd and CRL Energy Ltd, recognising the potential for the gas in New Zealand have initiated what is the largest ever assessment of New Zealand's coal seam gas potential. The premature demise of the giant Maui field has raised the focus of new gas developments and has increased interest in what we are doing. Over the past couple of years Kenham Holdings Ltd and CRL Energy Ltd have approached the assessment of the coal seam gas potential in a staged programme. Preliminary assessment of the data on the permit areas indicates that the potential resource may be up to 500 PJ. To date, preliminary appraisals have been completed or are underway on a significant number of fields. Exploratory drilling has been completed or initiated on several of those fields, with results from this work being fed into the preliminary modelling as it has become available. Given that in many of these areas there is no pre-existing information concerning their gas potential and world wide experience with lignite is practically nonexistent, it has been a steep learning curve with many surprises. However, initial gas content results and preliminary gas flow models have been on the whole, rather pleasing, with the commerciality of some developments already apparent.

Jan 1, 2003

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By P Card

Some project managers accept unsatisfactory economic evaluation modelling because they are unaware of what constitutes good practice. They tend to leave it to the evaluation specialist or others to decide. The AusIMM has published on its website a draft set of guidelines for technical economic evaluation which will allow these project managers to take control and demand worldÆs best practices.The style of the guidelines is described and the source of a worked spreadsheet example in Excel is given.Economic evaluation in project management is described. A simple test for the acceptance or rejection of evaluation work is offered. The nature of modelling and evaluation in each of the three study phases of concept, prefeasibility and final feasibility are described. Suggestions on the selection of specialists for each phase are given. The three levels of evaluation thinking are described, namely, modelling, valuation and evaluation. Finally the meaning of æfinancial analysisÆ is explained.The conclusion is that æthe role of an economic evaluation specialist is to create models and evaluations for the whole project team to readily understand and use: it is not to create models for his/her own useÆ.CITATION:Card, P, 2012. What project managers must demand from an economic evaluation!, in Proceedings Project Evaluation 2012 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By N Clarke, J Hunt, A Barros, N Guerrero, L Keeney

Grade Engineering® (GE) involves a range of integrated technologies and operating protocols for improving effective feed grade through early rejection of low value material prior to costly processing activities and has the potential to transform the economics of large, low grade, mining operations. Extensive GE test work by AngloGold Ashanti (AGA) and the Cooperative Resource Centre for Optimising Resource Extraction (CRCORE) determined that the Gramalote gold deposit in Colombia is highly amenable to implementation of grade-by-size screening to upgrade the ore at a production scale. To understand the relationships between geology and the upgrade response drill core and bulk samples were analysed at the Centre for Ore Deposit and Earth Sciences (CODES) as part of a larger CRCORE project to understand geological controls on grade-by-size deportment, i.e., the tendency for specific mineral phases to preferentially fractionate during breakage into different size fractions. This work is focussed on understanding the role of mineralogy and texture in influencing rock breakage and natural fractionation at a range of scales. Detailed logging of Gramalote drill core and mineralogical analyses including hyperspectral logging, portable and bench-scale X-ray fluorescence (XRF), plus low resolution Laser Ablation of intact drill core pieces, combined with data from site (drill logs, geochemistry, petrophysics) were used to evaluate the ore and alteration mineralogy, vein paragenesis and textural variability. This provided information on gold deportment and allowed the identification of favourable host veins. Bulk sample material from different ore grade zones was also analysed. A comparison with the results of GE testing shows that positive upgrade results are produced by rocks with abundant veins, particularly those associated with potassic and/or white mica alteration. This work indicates upgrade response can be predicted from drill core using data collected by a combination of automated systems including hyperspectral data, XRF, and detailed drill core logging.

Nov 10, 2020

By M Sparrow

The Victoria Park Tunnel project is an inner-city alliance project in central Auckland, New Zealand. The existing two-directional viaduct will be modified to single-direction flow, and a new northbound 440 m cut and cover tunnel will be constructed beneath Victoria Park. Three-dimensional (3D) visualisation media were used to communicate key design innovations to stakeholders and the general public. The 3D visual material has proven a useful tool for informing motorists of a new safety barrier method adopted for traffic management.This presentation will explain how 3D visualisation was incorporated in the project and will showcase the 3D visualisation media created for the project.

Mar 8, 2011

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R Talebi

A research project to better understand the rock mass behaviour and the seismic response has been conducted during the design and construction of the 9215 level at the E-Block sector of the Northern Star Kanowna Belle Mine. The research program was undertaken at a tunnel located 1100 m below the surface with the results applicable to feasibility studies on underground mining projects in highstress conditions, where failure can occur very soon after tunnel construction. Semi-circular excavation shapes coupled with the use of de-stress blasting techniques were designed to monitor the excavation in conditions of very high stress. The ground support was designed considering high energy dissipation ground support schemes (HED) as described by Arcaro et al (2021). The results indicate a decreased rock mass demand due to the change of excavation shape. Also, localised reduction in rock mass stiffness was achieved due to the implementation of de-stress blasting. Finally, increased ground support capacity was gained by the implementation of the high energy dissipation ground support schemes. The Kanowna Belle Mine has significant ore reserves at depths exceeding 1000 m below the surface. The results of this research will be used to optimise the extraction of the remaining E Stoping Block at depths exceeding 1350 m.

Mar 29, 2023

By C Artica

Two quantitative methods for Mineral Resource classification have been applied to a copper skarn deposit beneath a large open pit that is mining a world-class porphyry complex. A drill hole spacing study (DHSS) using the single block kriging method (SBK) and a conditional simulation method (CS) were applied to the skarn deposit and the results compared. Inputs to both processes included the proposed mining rate and stope designs to estimate the likelihood of achieving grade and metal production targets. Mineral Resource classification of the deposit considers the relative precision of tons, grade and metal predictions over quarterly and annual production periods. These relative precision estimates are calculated at 90 per cent confidence interval (CI). The SBK method represented the production period as a single large block. Kriging estimates were performed in the large block for various synthetic drill hole grids, and the estimation errors derived. The error was assumed to be normally distributed due to the large block size and quantity of samples, allowing CIs to be deduced. The CS method followed a conventional sequential Gaussian simulation workflow where grades were simulated with a 5 ft × 5 ft × 5 ft grid node spacing inside mineralisation domains. Each realisation was then averaged up to monthly production volumes represented by a combination of designed stopes, and the coefficient of variation (CV) for the averaged grade was calculated. CI on the relative precision of grade predictions were then deduced from the CVs. The two methods produced similar results; despite being calculated independently. CS results were used to report uncertainty in the proposed life-of-mine plan and highlight areas for additional drilling. SBK results were used as the basis for Mineral Resource classification as this method has been previously applied to the skarn deposit.

May 24, 2023

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

Jan 1, 2004

By R Jia, J T. Waldram

"The Caijiaying lead zinc mine is located in China, north-west of Beijing, in Hebei Province. The region experiences severe winters, below -35°C, and warm summers, up to 30°C. The mine and concentrator commenced operations in the second half of 2005 with a conventional tailings disposal system consisting of a tailings dam with peripheral ring main discharge and central water recovery. A second similar dam sharing one common wall was added later. In view of the extreme winter conditions tailings lines and ring mains plus spigots, together with return water lines, require insulation and electrical trace heating. The volume of process water trapped as ice in the tailings dam ponds each winter is significant. This seasonal variation presents a major difficulty in the management of process water availability. Although Caijiaying is an underground mine there was no backfill plant at the start of operations. As plant throughput increased more quickly than originally anticipated, tailings storage capacity became a prime concern. The construction of a backfill plant in 2007 reduced the pressure on surface tailings storage area requirements, but as suitable land on which to construct further tailings storage was both expensive and difficult to acquire, a more efficient use of the available area was required. Dry tailings storage, where flotation tailings are filtered to provide an immediate return of process water plus ‘dry’ tailings filter cake for stacking, provided an answer to both the land area required, and the water management difficulties. The paper details the reasoning behind the change and the benefits obtained at Caijiaying by moving from ‘wet’ tailings storage to ‘dry’ tailings storage.Citation:Waldram, J T and Jia, R, 2016. Caijiaying Dry Tailings Storage, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 379–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Parcell

"Ventilation risks in an underground mine have essentially remained the same for centuries, yet theevidence suggests that there are many coal mines that have failed to adequately control these risks.The conduit for the knowledge learned by previous generations exists in the mining legislation. In an ideal world, mines would not need legislation to tell them what to do; they would resolve the risks to an acceptable level so as to protect the safety of persons in the mines based on the acquired knowledge. There will be some who have been personally aff ected by a mining disaster but for the majority they will be remembered as a vague recollection of an event from long ago. The mining legislation is the repository for the knowledge and outcomes from inquiries of past disasters. The challenge for the current generation, and the generations to come is to appreciate the legislation that exists, so as to not ælearn the hard wayÆ. In reviewing most disasters there is comment or discussion on the adequacy of the legislation, which ultimately results in some amendment to the law. For each person, there is an increasing responsibility to ensure that the same mistakes are not repeated. Understanding the legislation, its history and its purpose is the fi rst step in ensuring thatventilation risks are eff ectively managed. Failing to do this will be disastrous. This paper discussesthe relevance, importance and potential pitfalls of coal mine ventilation regulation."

Jun 1, 2012

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By C L. McIntosh

The west coast of New Zealand’s south island is host to a large number of placer goldfields that stretch from the Westport area in the north to Gillespies Beach in the south and inland to the foothills of the Southern Alps. This area is host to a large number of alluvial, glacial and strand line deposits ageing in range from Recent to Tertiary. In recent years exploration models have been developed for off shore placer deposits on the continental shelf.Gold mining on the west coast has exploited placer gold resources from the 1860s to present, and with the recent surge in the gold price the industry is currently undergoing a resurgence. The current increase in mining is dominated by small-scale mechanical operations usually involving one to two people at each site; a few larger operations also exist such as the Grey River Dredge.Mining methods range from using floating bucket dredges to small diggers. Some of the mining technologies used are similar to those employed during the great gold rushes of the 19th century. Exploration and grade control techniques can be very rudimentary often relying on previous sampling programs or wide spaced bulk sample drill holes. Some bulk sample drilling is used on the larger operations as a form of grade control, most of the small operations tend not to use any ore control sampling prior to mining. Extraction techniques relying on simple gravity based designs with riffle tables or spirals are the most commonly used. Environmental standards are very high within New Zealand and require operators to return mined areas to preagreed to landforms. The high rainfall experienced on the west coast causes challenges to operators in regard to water quality. Technical issues combined with often limited capital provide for challenges to the operations.

Aug 22, 2011