Search Documents

By V Kumar, A S. Venkatesh, R K. Upadhya

The enormous iron ore deposits of eastern India are part of the volcano-sedimentary basins containing iron and to some extent manganese deposits that belong to the Iron Ore Group (IOG) of Archaean Singhbhum Craton, occurring as western and eastern limbs of a broad synclinorium. The eastern iron basin contains typically huge amounts of blue dust and powdery ores. There is a remarkable difference between the western flank ores and the eastern flank ores and the present study is part of the eastern flank ores from Noamundi. Demand for sintered fines as blast furnace feed coupled with the higher export price for lumpy ores that produce enormous amounts of fines during processing has created a situation whereby both primary and secondary fines, such as classifier fines, are being increasingly used as sintered feed for blast furnace. Systematic mineralogical and geochemical characterisation indicates that in many cases the ROM and classifier fines have to be processed to increase their Fe content and at the same time reduce their Al, Si and P contents. The fines which are already at micron sizes are amenable for beneficiation using the Mozley mineral separator and sink float test. It was observed that beneficiation was better and significantly greater by the sink float method than the Mozley mineral separator. Mineralogical and chemical studies of the fines reveal that around 80 per cent of alumina bearing minerals (gibbsite, clay and silicates) are present in the liberated form. Microscopic studies confirmed that the iron minerals are well liberated by controlled grinding to -300 mesh sizes with the beneficiation of iron ore fines and low-grade ores carried out using the Mozley mineral separator and sink float test. Beneficiation using the Mozley mineral separator increased the grade of concentrate with increasing flow rate of water as well as increase in amplitude of oscillation of the tray, but not very significantly with the increase in slope of the tray. In this method, though, iron concentration improved from 47 to 63 per cent with a recovery of around 67 per cent. It is not suitable for industry scale operation as only a small quantity of ores can be handled at a time. Beneficiation using the sink float test produced a better result with the Fe content increasing from 47 - 49 per cent to 66 - 68 per cent with a recovery of approximately 58 per cent. Initial feed Al2O3, SiO2 and Fe contents of 9.85 per cent, 15.3 per cent and 49.8 per cent respectively were beneficiated to 2.13 per cent Al2O3, 1.5 per cent SiO2 and 67.5 per cent Fe in the concentrate, with a recovery of 54.1 per cent. In contrast, using the Mozley table resulted in beneficiable contents 66.3 per cent Fe, 3.01 per cent alumina and 2.05 per cent silica. The combined alumina and silica content for the Mozley Table was >5 per cent, which exceeds the industry requirement of

Jan 1, 2005

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

By K Watters

API Management Pty Ltd (API) is currently developing the West Pilbara Iron Project (the ‘Project’). The Project is a substantial greenfi elds mining and infrastructure development proposed for the west Pilbara region of Western Australia. The Project will establish API as a new and independent supplier of direct shipped iron ore. API manages the Australian Premium Iron Joint Venture (APIJV) on behalf of joint venture participants Aquila Resources Ltd and American Metals and Coal International Inc. The APIJV was formed in February 2005 with the objective of developing a long-term iron ore export operation in the west Pilbara region.Development of Stage 1 comprises a 30 million tonne per annum (Mt/a) channel iron deposit (CID) operation scheduled to commence in the second half of 2014 subject to approvals. JORC compliant CID resources total nearly 700 million tonnes and the Stage 1 mining area comprises eight iron ore deposits located between 30 km and 85 km south of Pannawonica. Run-of-mine ore from the eight deposits is transported to a central processing facility for crushing, screening and blending into a sinter fines product, which API has named West Pilbara Fines or WPF. Construction of a 282 km main line heavy haulage railway from the Stage 1 mining area to the proposed greenfields multi-user port at Anketell Point near Wickham, is capable of accommodating large Capesize bulk carriers and providing export facilities for other third parties. Capital investment in the order of $A6 billion includes essential support infrastructure including power, water, accommodation, roads and an airport at the mine.A feasibility study for the development of the Stage 1 mine, rail and port infrastructure has been completed along with environmental surveys of the mine, rail and port areas with Public Environmental Reviews (PERs) for each submitted for public review by end 2010. Consultation and cooperation with various stakeholders of the Project areas, and early engagement with traditional owners of the respective areas has commenced. Various sampling and metallurgical characterisation programs combined with independent institute and steel mill based testing have confirmed the positive sintering characteristics of WPF ore, which is higher in alumina (3.37 per cent) than typical Pilbara ores. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By S Garnes, W Austerberry, S Fraser

Despite significant investment in safety in the mining industry (mostly focused on processes and systems), many companies are unable to sustain and further improve their performance resulting in continued workplace incidents. The problem persists despite the best efforts of companies and allocation of resources to achieve Zero Harm. A DSS survey in 2019 found that two out of five companies that cannot manage risks and face disaster, leave the market within five years. All safety/risk management systems have the common steps of risk identification, prioritisation, design of controls consistent with risk tolerance, and verification of implementation/operability of controls. This is then complimented with improvement to one or more of the above elements through learnings obtained from incident investigations. In principle, the above process should work to reduce risks to, and keeping them at, a risk level consistent with risk tolerance in the organisation.

May 5, 2022

By J Maxlow, M J. Woods, M P. Sandy

The Newcrest Mining Limited Telfer operation comprises both open pit and underground operations producing gold and copper. The underground operation is made up of three production areas, the sublevel cave (SLC), M Reefs narrow vein open stoping and Western longhole open stoping areas. With stoping situated on the abutments of a mature and active sublevel cave, the interaction between mining areas is often complex. This is particularly evident in the M Reefs orebodies with high levels of extraction in all four reefs, and reliance on pillars to maintain local and global stability. A key concern was the potential for a cascading pillar failure to develop and rapidly progress through the M Reefs stoping area. The monitoring plan needed to capture any change in overall stability and identify if deformation was caused by pillar failure within the M Reefs and hanging wall closure, or shear on the reefs caused by SLC influence.

Nov 29, 2022

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By L MacDonald, D Molver, D Pepper

Increasing contamination/impurity levels (including arsenic, antimony, mercury etc.) of concentrates is an issue of global commercial and health / environmental significance. With increasing environmental pressures at smelters, penalties for contaminants in concentrates continue to rise, accompanied by lower reject limits. There is a strong incentive for miners to investigate alternative means to remove contaminants in order to increase the value of complex ores and concentrates. This paper discusses the global problem of contamination in complex ores and concentrates, how the Toowong Process technology is a potential solution to this problem, and the opportunities this technology brings to the business of dealing with deleterious elements. CITATION: MacDonald, L, Molver, D and Pepper, D, 2018. The Toowong process for treatment of complex ores, in Proceedings Complex Orebodies Conference 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A G. Guinea

Every person in an organisation has what could be called ‘a different take’ on what it means to be a safety leader. The directors will tell you they are ultimately responsible for everyone’s safety and that they can be imprisoned as a consequence of a workplace fatality. Managers, take more of a focused approach and would explain that they are totally responsible for the safety of their teams. And then there are front-line leaders. Those that not only have the responsibility (like directors and managers) but they also have the accountability, and the ability, to influence how safely their teams work. But it is not just physical safety that leaders should be concerned with.

May 5, 2022

By P J. Bangerter, J Pan

Optimising for Net Present Value (NPV) with a strategic optimiser such as COMET, Prober-E, Blaser or Minemax has hitherto lacked a dynamic method for analysing the so-called third-order outcomes (such as Carbon emissions) of optimisation within life-of-mine planning. Optimisation, per se, has natural effects on carbon emissions in a life-of-mine plan. Contemporary strategic planning employs a mathematical optimiser to make sense of non-linear data (ie a block model) and produces a best-NPV optimised mining schedule, within a set of constraints. The very act of optimisation influences emissions, and in a dynamic way.

Aug 2, 2023

By M Liang, C Putzmann, D Gokaydin

The mining industry faces numerous challenges in swiftly evaluating and exploiting new mineral deposits to meet the escalating demand for critical minerals and metals. These challenges necessitate the adoption of innovative techniques and technologies to expedite development cycles and facilitate the efficient exchange of knowledge and expertise. Traditional mineral exploration methods rely heavily on data governance, visualisation tools, and expert interpretation skills, often operating in isolation and limiting the integration of valuable data and knowledge (Lindsay and Perrouty, 2019). To address these integration challenges and bridge the industry’s knowledge gap, the concept of a digital twin offers a holistic solution (Ahn, 2021; Nagovitsyn and Stepacheva, 2021).

Sep 1, 2024

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

By Falbo A, Barbaro M, Esposito MA, Passariello B

Acidic reductive leaching is one of the best known and most widely employed chemical processes for beneficiating minerals of industrial interest. Conventional acidic leaching with sodium dithionite (Na2S2O4), employed to bleach industrial minerals used in the production of ceramics, glassware, paper etc, does not always allow products of high quality to be obtained. In the work reported here two reducing agents, ascorbic acid and oxalic acid, have been employed in a medium acidified by means of sulphuric acid. Continuous systematic tests have been performed on a kaolin sample containing 0.8 per cent Fe2O3, adopting various operating parameters such as, leaching time, temperature and reagent concentration. In each case the total quantity of bi- and trivalent iron dissolved was ascertained. Removal of 80 per cent and 100 per cent of iron with ascorbic and oxalic acid respectively was obtained, while less than one per cent of iron was dissolved in the presence of sulphuric acid only. Products having a very good degree of whiteness (92 - 94 per cent) were obtained, whereas with sodium dithionite the degree of whiteness was in the 85 to 88 per cent range. The best conditions identified were applied to a sample of quartz for the removal of ferric impurities.

Jan 1, 1993

By K Brand, M J. Ind, M Rynhoud

Water management at a tailings storage facility (TSF) presents one of the major risks to the safe performance of the facility. International and domestic dam safety guidelines assess a dam’s hazard category based on the consequences of a dam failure and the subsequent downstream damage to the environment and communities.Often a rigorous risk assessment is undertaken during the design stages to identify and control hazards associated with water management through life-of-mine (LOM) phases. However, as experienced during the recent downturn in commodity prices, early closure of a mine can occur rapidly and unexpectedly. Although guidelines such as the Australian National Committee on Large Dams Incorporated (ANCOLD) recommend that one of the key objectives of integrated TSF planning is to ‘plan all phases of a tailing dam’s life to ensure adequate storage capacity including early closure ’ (Australian National Committee on Large Dams Incorporated (ANCOLD), 2012) this is often overlooked by owners who are focused on fulfilling the mine’s potential and early closure is not on their radar.CITATION:Ind, M J, Rynhoud, M and Brand, K, 2016. Life-of-mine spillway strategy – managing risk associated with surface water at a tailings storage facility, in Proceedings Life-of-Mine 2016 Conference, pp 209–211 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016