Search Documents

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Knights

This paper examines the process and specialised skills required to extract insight from data routinely collected by mine operations, maintenance, engineering and environmental departments. Typical insights include: enhanced understanding of root causes; recommendations for next best actions; and simulation of likely scenarios. The skills required for advanced analytics are not currently the domain of mining engineers. The professions required by tomorrow’s mines are likely to be diverse and multi-disciplinary, and will include control engineers, software engineers, mathematicians and statisticians. A case study is presented that correlates mobile equipment production delays with rainfall events across three mines on the east coast of Australia. One mine is shown to have significantly more rain related downtime than the other mines, providing compelling evidence to improve productive performance.

Nov 22, 2011

By T Belligoi

Diamond cores and drill chips provide the only direct physical evidence for ore containing rocks. Early characterisation of cores and drill chips is important as it provides critical information for downstream processing. Traditional characterisation techniques include visual logging by a geologist or analytic and spectroscopic methods but they are time consuming and can miss some important textural or geomechanical features.The goal of this work is to evaluate the application of image analysis to iron ore cores and drill chips and to suggest improvements to existing core-scanning and chip monitoring systems. Two samples of massive ore differing by their mineralogy and texture, as well as two different batches of drill chips, have been imaged and analysed. Results are compared in function of the imaging system and the classification algorithms.As a conclusion, despite the necessity for more testing and improvements in calibration and lighting, it is obvious that image analysis technologies can bring a lot of useful information in the perspective of a geometallurgical mapping of the deposit.

Jul 11, 2011

By Newell RB

Grinding circuits are used in most mineral processing plants. Their widespread application makes the efficient running of the circuits essential to almost all resource projects. This paper will show that, with the application of modern multivariable control techniques, improved plant performance can be obtained when compared with conventional single loop control strategies. Results are presented for a simulated closed-circuit ball mill.The grinding circuit was controlled using the rod-mill water and primary and secondary sump dilution flowrates as the manipulated variables. Variables controlled were the primary cyclone feed flowrate, the primary cyclone feed density and the particle-size measurement (percentage smaller than 75 um).

Jan 1, 1985

By Parrington PJ, Bailey A

Serious exploration for carbonate-hosted lead/zinc deposits in the Pillara district commenced in 1971 when Trend Exploration acquired exploration tenements covering stream sediment anomalies in the Limestone Billy Hills area. Shell Minerals managed the project from 1974 to 1976, and BHP Minerals Limited assumed management during 1976. Carbonate-hosted 'Mississippi-Valley- type' Pb-Zn deposits most commonly occur in Palaeozoic shallow marine carbonate complexes. At Pillara upper Devonian (Givetian/Frasnian) reef complexes are preserved on the flanks of Precambrian basement 'highs'. Within platform and atoll facies limestones sphalerite-galena- marcasite-calcite mineralisation occurs as disseminations, veins and breccia matrix, mostly associated with fractures and fault zones. Early exploration concentrated on detailed surface geochemistry and IP geophysical surveys, with geological mapping and shallow target percussion and diamond drilling. Results were discouraging and did not indicate potential for a shallow base metal resource. During 1976-77 BHP adopted a grid diamond drilling exploration technique and commenced testing an area of approximately 50 sq. km, initially using an 800 m square grid. In 1978 high grade mineralisation was intersected in an area subsequently named Blendevale. This was in the seventh diamond drill hole in the 800 m grid drilling programme, and to date more than 400 holes have been cored in the Pillara area. Detailed drilling at Blendevale has defined a number of mineralised breccia zones within an area of 2.4 km x 0.5 km, at depths of 100 m to 600 m below surface. The breccia bodies are associated with a series of north-south trending normal fault zones, forming a graben structure. The mineralisation occurs as breccia matrix surrounding unaltered limestone clasts, as veins filling steep fracture zones, and as

Jan 1, 1986

By He BQ

Static attachment of bubbles to solids is contrasted with dynamic attachment in flotation cells. The times of contact during particle-bubble collisions in dynamic attachment are compared with the induction time determinations and the kinetics of thinning of the liquid films separating solids and bubbles. The thinning is examined mainly in terms of electrostatic and dispersion (van der Waals) contributions to the disjoining pressure existing in the films. The local heterogeneity (on a molecular scale) of charge distribution invariably present at all interfaces (even at conditions of zero zeta potential) calls for some means to minimize possible electrostatic repulsions which arise when the electrical double layer at the air-bubble interface begins to overlap that present at the solid surface, on encounter between particles and bubbles. It is postulated that dipoles of frother molecules, owing to their ability to "flip over" (polarise), replace localized electrostatic repulsion by attraction within fractions of a milli- second, as long as the structure of the frother molecules is sufficiently "bulky" to maintain diffuse films (of mixed collector-frother) at the air/liquid interface of bubbles. The relaxation times of dipoles (signifying their "flipping over" ability) have to be shorter than the collision times between particles and bubbles for particle-bubble attachment to be facilitated under dynamic Conditions.

Jan 1, 1984

By Valenta R. K

A technique is presented for the integrated forward modelling of the three-dimensional structure and the geophysical response of multiply deformed terrains. This technique allows information collected by field geologists and geophysicist to be reconciled by the development of a simplified kinematic structural history of the area. The structural modelling simulates the deformation history of the area in terms of a succession of structural events, such as folds, shear zones and intrusions. The interaction of these events with a starting stratigraphy results in the prediction of the geometry of the structures. By specifying geophysical rock properties for the units in the initial stratigraphy predictions are possible for the potential field anomalies for gravity and magnetics. This approach is suited to a range of applications, and its uses in the modelling of regional structures, testing of geophysical data processing, volume balancing, multiply constrained inversion and training are discussed.

Jan 1, 1995

Portfolio management tends to separate the functions of Asset Allocation and Stock Selection, so the person responsible for reviewing an expert's report on a company would typically be choosing between companies rather than between a company and cash or bonds. How these choices are made depends on the investment time horizon, philosophy and style. Two styles, momentum investing and value investing are contrasted and the role of valuation methods within the framework of each style is evaluated. Finally, pricing is distinguished from valuation.

Jan 1, 1994

I WISH to express to the members of the Institute my sincere appreciation of the distinction which they have conferred upon me by again making me their president. It also gives me great pleasure to once more welcome the Institute to Mount Lyell.Since your last visit certain improvements in plant have been made, which I trust you will have found interesting, and which show that, though located in a remote corner of the world, we are abreast of the times.The opportunities which a recent lengthy trip to America has given me to observe the degree of interest which our local smelting practice continues to arouse in metallurgical circles make it seem appropriate that I should take advantage of your visit to lay before you some detailed information on the more practical features of pyrite smelting, particularly as carried out at Mount Lyell. There are only a few places in the world where the method is now being practised in approximate purity-only about half...

Jan 1, 1915

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995

In May 1977 a new dam was commissioned for disposal of 600,000 metric tonnes/year of tailings. Design basis, costs and construction problems are described. Problems arose, assoc- iated with lack of experience in building such a dam "from scratch". Solutions are described land costs given.

Jan 1, 1978

A comprehensive analysisof rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging, interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcorc is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure.

Jan 1, 1990

By Jarvensivu M, Ylinen R, Jamsa-Jounela S-L

The paper presents a new integrated system for control of concentration processes. The system is based on cluster-based modelling taking the ore quality into account and a new on-line particle size analyser capable also for reliable measuring of particle size distribution of concentrate. A metallurgical precontrol audit was performed at the Hitura concentrator in order to design the control strategy of the integrated grinding and flotation control. A new analyser PSI-200, was used to the measurement and control of the distribution of nickel in the total particle size range. An expert control system using the cluster model together with a new control strategy for decision of necessary control actions is outlined. The method has been tested to real data from mineral processes. The results are in good correspondence with empirical process knowledge. KEYWORDS: Cluster analysis, expert control, flotation control, mineral processes, modelling, particle size.

Jan 1, 1993

By M Boyd

The University of Wollongong was named University of the Year 2000, for its work in preparing students for the e-world. Computer facilitated learning is being introduced into subjects throughout the engineering course. First year mining engineering students are introduced to computers, e-communication, using the UniversityÆs web based information system, and web based subject delivery. Mining engineering students in the mid-years of the course use programming languages and numerical computation software such as MATLAB, while students in the final years use a range of commercially available professional engineering software such as TALPAC. Most of these subjects are offered as part of the UniversityÆs Learning Online program, co-ordinated by its Centre for Educational Development and Interactive Resources (CEDIR). Learning Online subjects are delivered using the Web Course Tools (WebCT) environment. WebCT allows all resources to be accessed through the web, allows email communication between lecturer and student, and allows discussion groups for the exchange of ideas. Students can submit their assignments through WebCT and receive immediate feedback. This paper describes how WebCT has been used to deliver a first year engineering computing subject, mid-year numerical computation subjects, a mining economics subject and mine planning subjects.

Jan 1, 2002

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

The movements of the major continental cratons and the distribution of the principal tectonostratigraphic terranes are reviewed in the Circum-Pacific region during Phanerozoic time. It is concluded that major periods of orogeny and consolidation of accreted terranes in the Circum-Pacific region is best correlated with periods of advance of cratonic blocks over the Pacific Ocean basin combined with relative convergent to transpressive motions between the cratons and the Pacific Ocean plates. Continental collisions and collision of terranes with continental margins has not been a significant geodynamic process in Circum-Pacific tectonic evolution. The permanency of the Pacific Ocean basin throughout 500 MA is remarkable. It appears no continental block or large continental fragment has ever entered or crossed the Pacific Ocean basin since early Paleozoic time. This area where no continent has entered for 500 MA is almost coincident with the present Pacific Ocean basin and seems associated with the 25 to 100 meter geoid high which dominates the present-day figure of the Earth.

Jan 1, 1990

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023

By Guerney P. J

A suspension of finely powdered ferrosilicon in water is the dense medium used in the gravity upgrading of iron ore, diamonds and other minerals. Ferrosilicon can he lost in the plant through corrosion. The greatest corrosion losses occur when

Jan 1, 1997