Search Documents

By Massy-Greene RB

Limited recourse financing techniques reduce the financial exposure of equity holders to major mining projects by transfering some of the risks to the banks which provide loan funds for project development. This can only be achieved by a clear understanding of the principles involved. Engineering and management decisions on how the resource is to be developed and extracted must be made in the light of lender's requirements. The structure of sales contracts, joint venture agreements and many other documents can be important in limited recourse financing. If projections show that the debt can be repaid from project cash flow, loan agreements and other arrangements can restrict lenders ability to look to the equity holders for repayment of project loans.

Jan 1, 1981

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005

By M Neurohr, B Wacker, D Mensing, C Murphy, W Kitz

Mining operations have large power requirements. The biggest consumers of energy are the drives for the mills located in the concentrators. Assuming that the decision is made on how many mills are needed and how big these mills will be, it can be determined how these mills should be driven. The decision as to which drive should be applied depends on design limits for different mechanical or electrical drives, anticipated operation modes, capital expenditure optimisation and lifecycle cost optimisation.The task for the engineer specifying the drive equipment is to select a drive solution that can debottleneck the operation, avoid interruption of production and enhance the reliability of the process. At the same time, the engineer must choose a design that enables cost optimisation either in a single investment or in relation to the total cost of ownership (TCO).This paper outlines different mechatronic or electric drive alternatives for tube or horizontal mills applied in the mining industry, along with their advantages and disadvantages. The paper covers a wide range of applicable drive systems and provides a background to the benefit of applying integrated drive systems.CITATION:Wacker, B, Kitz, W, Murphy, C, Neurohr, M and Mensing, D, 2015. Application of different drive systems for horizontal mills, in Proceedings Iron Ore 2015, pp 205–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Abell RS, Wyborn D, Solomon M, Stuart-Smith PG, Henderson GAM

The two major massive sulphide deposits in the Silurian rocks of southern NSW, Captains Flat and Woodlawn, differ from classical Kuroko deposits in several ways, e.g. they lie on the flanks of felsic volcanic piles in volcano-sedimentary marine sequences, are relatively thin and large compared to individual Kuroko deposits, show prominent banding in lead-zinc ore, and contain arsenopyrite. Qualified stuctural and stratigraphic correlations of the various fault-bounded remnant Silurian sequences that host these deposits provide the basis for a new interpretation of the regional geological setting that also differs from that of the Kuroko deposits (Ohmoto, Tanimura, Date, Takahashi, 1983), and sheds further light on the distribution of volcanogenic massive sulphide deposits in the Silurian rocks of NSW.

Jan 1, 1987

By S Roberston, G Batt, R Shanahan, B Shah, A Trench, H Bromfield

The geographic imperative of ore systems leaves mining, more so than virtually any other aspect of modern industry, heavily dependent on obtaining and maintaining social licence to operate. A prospective miner cannot arbitrarily walk away from a deposit in search of more favourable community perceptions – concentrations of mineral endowment represent highly specific and fixed elements of the landscape, and their development and extraction thus requires the acceptance and trust of a specific network of landholders and stakeholders, sometimes with diverse and even competing interests in the development and use of the local environment. Weakness or absence of such social licence can bring added costs and complexity to developing and operating a mine – and in extreme cases even result in project failure. Because it must be maintained throughout the life of a project, such social risk becomes a substantial part of overall project risk profile, particularly during routine operations once initial technical and development risks have been largely resolved.CITATION: Bromfield, H, Roberston, S, Shah, B, Shanahan, R, Trench, A and Batt, G, 2018. On equitable distribution of mining wealth and the social licence to operate imperative – an African case study, in Proceedings Complex Orebodies Conference 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J J. Cilliers, K Hadler, A W. Stra

This paper examines the use of the FrothSim flotation simulator to improve the performance of an industrial column flotation cell. The performance of an industrial retreat column cell is simulated, and, from the discrepancies between the simulated and experimental results, a problem with the wash water distribution is postulated. The scientific reason for the reduced performance with uneven wash water addition is described in detail. Further simulations indicated the potential for improvement with an even wash water distribution, resulting in both improved performance and reduced wash water usage. The simulated uneven wash water distribution was confirmed industrially, and the headers were redesigned and installed. A sampling campaign to compare the performance before and after the modifications showed that the flotation performance was improved dramatically, with a statistically significant decrease in gangue recovery, without a commensurate reduction in valuable mineral recovery.

Jan 1, 2005

The prime requirement is market, which for NZ inevitably means overseas markets. In order to be internationally competitive, the economies of scale and mechanical handling are essential. Since significant markets have not been sought, the full extent of our industrial mineral potential is not known. In general the technology exists to impart the desired quality, but at a price. Price is the main constraint, which may confine truly competitive operations to coastal situations to avoid high internal freight charges. Some commercial deposits of construction materials are being sterilised by zoning, making the costs to the consumer and country unnecessarily high. Unless management is enlightened and marketing is forceful, it can restrict growth. There is a good case to mount a search for phosphate minerals. The main growth areas are likely to be direct shipping ores like limestone, silica sand, and olivine, but in particular pumice.

Jan 1, 1978

By G K. Robinson

The existence of bias in samples taken by cross-stream sample cutters has been investigated using three-dimensional discrete element method (DEM) modelling. Detailed quantitative information on overall extraction ratios, size specific extraction ratios, missed and extra sample components can be made by comparing a reference sample to the actual sample. A key advantage of using this modelling approach over physical experimentation is that the reference sample can be measured on precisely the same portion of the stream of material as the actual sample, thereby allowing the elimination of a significant fraction of the variability and allowing statistically significant results to be obtained using many fewer replicates. Quantitative analysis of results broadly supports the commonly-used rule that the cutter aperture should be at least three times the nominal top-size of the material being sampled, but does not support the commonly-used rule requiring increase in cutter aperture if the cutter speed exceeds 0.6 m/s. Sampler performance can be understood in terms of the balance of forces in the congested region of material formed by the slowing of the particle stream due to collisional interactions around the mouth of the cutter.

Jan 1, 2008

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By I Mason, A Bray, K Smith, T Sindle

Borehole radar is a proven geophysical technology that can be used to map an orebody ahead of mining. This paper will present a case study, where borehole radar is being used within the mining cycle to map out orebody blocks, both as a strategic and tactical tool. Refined equipment and procedures now enables a slimline borehole radar tool to be deployed on the end of drill rods, making it easier and faster to deploy in an underground mine with minimal impact on the mining process. Boreholes are drilled in advance of mining; cover holes to ensure the competence of the hanging wall and geology holes to determine the location and grade of ore are two such examples. All of these boreholes can be entered using a borehole radar tool to map geology and structure ahead. The radar data can provide images of the orebody as well as help detect potential water bearing structures that could impact on safety at a mining face.

Jan 1, 2009

By P M. Hetherington, M P. Murphy, K E. Crook, F Pym

Resource characterisation is critical for informed decisions in both strategic and operational space. The sources of information for resource characterisation are limited by: direct measurement of resource attributes, such as grades, rock-types, mineralogy, and are available only from sparse locations, ie drill holes; or indirect geophysical measurements such as seismic, gravity or electro[1]magnetic survey. Data collection tools, methods, and processing technologies are constantly improving providing a broad spectrum of options for data collection strategies. The cost of each data survey varies from thousands to millions of dollars with the value of each additional data having diminishing return for a particular business decision. The value of information analysis provides the optimal decision on data collection strategy within a limited available budget. This work presents an example of value of information analysis for new Blast Hole Assay Tool (BHAT) and Reverse Circulation Grade Control (RCGC) data used in addition to the wider spaced exploration data. The value of information is quantified in terms of reduction of grade uncertainty, ore loss and dilution by comparing different combinations of data collection methods. Four different strategies were considered: exploration samples in addition to 50 per cent of blastholes surveyed with BHAT, exploration samples in addition to 33 per cent of blastholes surveyed with BHAT, exploration with wide-spaced RCGC data, and exploration without additional grade control. For each strategy the observed values have been simulated using advanced multivariate geostatistical simulations and compared with simulated ground truth models. The calculated uncertainty, ore loss and dilution informed the optimal data collection strategy. Opportunity to reduce sample density from the nominal 50 per cent of drill holes was evaluated.

Mar 22, 2022

By Davies K. E

Several nuclear techniques have been assessed for application to online conveyor belt analysis of oil yield from Rundle oil shale. The most favourable technique is neutron inelastic scattering which determines the total carbon content of bulk shale samples. Correlations of chemical laboratory assays for 540 Rundle oil shale samples show that oil yield can be predicted from total carbon to within 11 litre/tonne.Laboratory experimental work on 17 bulk samples of Rundle oil shale indicated that carbon and oil yield can be determined to within 0.6 wt per cent and 9 litre/tonne, respectively, using the neutron inelastic scatter technique. A practical neutron inelastic scatter gauge for application on a 23 mm thick reinforced conveyor belt could consist of a 5 curie 241 Am-Be neutron source and a 150 mm diameter x 100 mm thick Nal(TI) detector. With this gauge, the analysis time to achieve a counting statistical error of 6 litre/tonne should be about five minutes.

Jan 1, 1985

By K Rozlapa, P Waters, H Middlemis

A major challenge for closure planning at mining operations below the water table is evaporation from final void pit lakes and concentration of salts, which can impact on downstream groundwater (and surface water) flows and quality. Where such impacts are deemed unacceptable, the closure approach that is often adopted is to infill the final voids with waste rock to above the pre-mining water table to prevent the development of a pit lake and subsequent evaporative losses. BHP Billiton Iron OreÆs Marillana Creek (Yandi) mining operations face these issues. The orebody is a channel iron deposit that forms the major aquifer in the region, which will be completely mined as a series of elongated open pits over tens of kilometres. The major constraint on mine closure planning was the stripping ratio of less than one, which means that there is insufficient waste rock to infill all areas to the pre-mining water table. Hydrogeological investigations and groundwater modelling indicated that standard mine closure approaches would result in pit void lakes becoming saline sinks unless the residual void geometry was optimised to minimise evaporation and maximise throughflow. The solution developed is a cost-effective long-term mine plan that meets all mine closure objectives, and involved:the selective infilling of all pits, largely using run-of-mine waste dumping with limited re-handling; the diversion of the major part of up-catchment creek flows around the mining operations to allow mining of the resource under Marillana Creek crossings, which in turn restricted overall aquifer recharge and reduced the elevation of the long-term water table; the diversion of some minor creek tributary flows into specific locations within the mine path to induce hydraulic gradients to maintain groundwater throughflow and water quality; and close integration of mine plan optimisation (mining and waste dumping schedules) with groundwater modelling scenarios to achieve acceptable environmental outcomes. This approach is designed to result in no reduction in downstream surface water flows or quality, maintenance of adequate downstream groundwater throughflow to support groundwater dependent ecosystems, and no reduction in the beneficial use status of the downstream groundwater resource.

Jan 1, 2006

To solve the mining safety and health needs of the future, access to, and sharing of, timely and relevant information will be crucial. The next generation of the Web will provide tools (RDF, OWL, SPARQL, etc) to define and link content for more effective discovery, integration, and reuse across applications and organisations. A recent Gartner Research Report (Finding and exploiting value in Semantic Web technologies on the web, May 2007) predicts these technologies will begin to coalesce in ten years. Implementing this Semantic Web requires structured web content described via metadata (information about information). If an industry or enterprise bases its metadata on a common vocabulary, it becomes possible to share and reuse information. The National Institute for Occupational Safety and HealthÆs (NIOSH) Mining web site provides access to more than 1500 NIOSH-developed publications, products, and topic pages on issues as diverse as ground control, respiratory diseases, and mine emergency management. As the site has grown, locating content has become increasingly difficult. To improve the searching process, a panel of internal experts representing all major research programs was established to develop a controlled vocabulary for indexing that content. The outcome is the NIOSH Mining Safety and Health Thesaurus, a faceted, hierarchical thesaurus containing hundreds of mining safety and health terms organised into 20 facets (eg diseases, injuries and disorders; hazardous events and exposures, equipment, engineering and administrative controls). One immediate goal of this project is to reduce the complexity of locating information on the NIOSH Mining web site by implementing metadata and faceted information retrieval techniques. Another goal is to stimulate discussion in the international mining community regarding developing metadata standards so the industry is ready to adopt future Semantic Web technologies to improve access to mining safety and health information.

Jan 1, 2008

By B Mennie, R Poedjono, G Coad

PT Freeport Indonesia operates a large copper and gold mining operation near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. This is a remote location with its own set of unique operational characteristics. The mining and concentrating operations typically produce a concentrate containing 2500 tpd of copper and 6000 oz of gold per day from the combined mining of a 45 000 tpd (ore) block cave operation (DOZ Mine) and a 190 000 tpd (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open Pit mine will be exhausted in 2015 at which time FreeportÆs operations will entirely underground mining methods. The Common Infrastructure Project (CIP) incorporates the elements required for the shift to underground mining at a production rate approaching 200 000 tpd. The AB Adit portion of the CIP will provide deep level access to the Grasberg Block Cave (below the Open Pit), Kucing Liar, Big Gossan, and the Mill Level Zone orebodies. Commencement of the project was September 2003. The Grasberg Block Cave is planned to start production in 2014. This paper provides details on the project scope, innovative contractual framework, advancement of mining methods throughout the life of the operation, equipment selection, manpower selection, training, geological, and socio-political conditions related to the project.

Jan 1, 2005

By F D Durao, Muge F. H, Rogado J. Q

In the scope of the project named CAPUME II (EEC BRITE/EURAM contract - project MA2M-CT90,-0042(SMA)) for the development of an integrated mine planning system for underground mines, two of the main tasks were the development of a short-term mining planning procedure (module) and a numerical simulator of the mineral processing plant of Pirites Alentejanas - PA. The short-term mining planning module defines the mining sequences by solving a constrained minimisation problem. The ore grade variability is the objective function subject to the geometrical constraints of the mining method and to the maximum of `internal blending'. The optimisation problem is solved by applying a dynamic programming algorithm. The plant simulator is an essential tool of the planning system allowing the preview of metal grades/recoveries of copper, lead and zinc of concentrates streams, given the corresponding metal assays of the run-of-mine ore, defined by the short-term mine planning module. This way, the management can plan the short-term mining operations (the weekly sequence of exploration blocks and the internal planning) in order to fulfill given required conditions, based on a shipment schedule and on a purchaser's formula. In this paper, after a short description of the short-term mining planning module and of the simulation package named SIMUL, a synthesis of the main model development steps and the results of some simulation runs are presented and discussed.

Jan 1, 1995

By B Lavin, R Sanford

This paper examines the application of Lean Manufacturing in a mining environment, based on experience within the Rio Tinto entities: Rio Tinto Aluminium, Northparkes Mines and Hunter Valley Operations. The three applications have tested the flexibility of the Lean methodology. Within Rio Tinto, Rio Tinto Aluminium was the first group to introduce Lean. The rollout began in late 2004. It was introduced firstly at Boyne Smelters, Gladstone, as a model site with the initial application in the Carbon Bake Furnace area. It was later extended to other sites including the Weipa Bauxite Mine. LeanÆs successful application within Rio Tinto Aluminium was in part responsible for its recent adoption by other Australian-based Rio Tinto business units including Northparkes Mines, a copper mining operation in Central New South Wales, and Hunter Valley Operations, a group of four coal mines in the Hunter Valley region of New South Wales. Lean is also being adopted by Rio Tinto Iron Ore. Rio Tinto Aluminium introduced Lean Manufacturing to complement an existing Six Sigma business improvement program and to achieve continuous improvement activities at a workplace level. Lean provides a similar level of rigour and discipline to Six Sigma but its application is everyday and for everyone, everywhere in the workplace. It is a valuable management tool. In a short time, Lean has achieved good and sometimes spectacular results improving productivity and efficiency at all sites, including our mining site. Within Rio Tinto Aluminium, it has also had beneficial impacts on our ability to develop and retain employees.

Jan 1, 2006

By K Vallo, T Haimi, J Pihlasalo, J Hamuyuni, M Lindgren, F Tesfaye

Decarbonisation of the steel industry has recently attracted a lot of research and technological development. Most of the technological developments are centred around the replacement of blast furnace (BF), which has been the main primary smelting furnace in the ironmaking step of steel production. Replacement of the BF is not an easy task because of BF’s many established capabilities over the years, especially its ability to use low-grade iron feed. In this regard, Metso has developed its own technology, Metso’s Outotec direct reduced iron (DRI) smelting furnace, to tackle this problem. The recently developed six-in line electric furnace for DRI smelting can be used for primary smelting of DRI from blast furnace grade iron ore. Unlike the electric arc furnace (EAF), the DRI smelting furnace can handle larger slag volumes that emanate from the high gangue in BF grade DRI. Therefore, fluxing plays an important role in operating the DRI smelting furnace. This paper presents fluxing options and proposes slag quality and operating windows for the DRI smelting furnace. Also, the effect of slag on refractory durability will be discussed.

Jun 19, 2024

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980