Search Documents

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By F. J. Martin, W. G. Hubler

The Beattie mine is at about the center of Duparquet township in the Province of Quebec, Canada. It is 22 miles northwest of the town of Noranda. The elevation is approximately 1200 ft. above sea level. This locality, long considered a favorable one from the geological point of view, has been prospected for over 20 years, but no discoveries of economic importance were made until the present orebody was found by John Beattie in 1930. The specific gravity of the ore is 2.77. The gold occurs in intimate association with the sulfides, pyrite and arsenopyrite, which in turn are very finely disseminated in a silicified porphyry. The bulk of the gold is associated with the pyrite, only a small proportion being with the arsenopyrite. There are small amounts of magnetite, ilmenite and chalcopyrite present in the ore. There is also some hematite in the ore that is mined from near the surface in the open pit. Metallurgical Problems and Methods or Attack 1. The ore is extremely hard and resistant to grinding. 2. The sulfide minerals are finely disseminated in the gangue. 3. The gold, in turn, is so intimately associated with the sulfides that grinding to even 5 microns will not release all of the values for cyanidation. 4. It is necessary to make a high ratio of concentration in order to obtain a product sufficiently high in gold to meet high shipping and treatment charges. Hardness of the Ore.—Owing to the extreme resistance of the ore to grinding, it was recognized that grinding costs would be high. Microscopic tests showed that grinding to 95 per cent minus 325 mesh would be necessary to liberate a sufficient amount of the values in order to obtain a tailing assaying 0.02 oz. gold per ton, which is considered to have the economical minimum gold content that can be obtained. It is not feasible to grind this hard low-grade ore (0.18 to 0.20 oz.) to 95 per cent minus 325 mesh, so it was necessary to overcome the problem in another way. The following method was decided upon: (1) Fine crushing to minus 1/4 in.; (2) relatively coarse primary grinding; flotation of low-grade concentrates in the primary and rougher circuits and discarding the

Jan 1, 1935

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930

By Henry Hebley

IN recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and clean-ing of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal.

Jan 1, 1933

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x'1 x'2 x'3) system is x1 x2 x3 X'1 a11 al2 a13 x'2 a21 a22 a23 x'9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965

By P. G. Beckett

The problem of handling the large quantities of water encountered in the Old Dominion mine presents many features of interest. In the present paper are discussed the probable sources of water, the pumping equipment, the increased flow into the mine in the early part of 1915, culminating in the flooding of the 18th and 16th levels in March of that year, and the difficulties that were met with during the high-water period. I. PRELIMINARY The Old Dominion mine, situated 1 mile north of the town of Globe, Ariz., has long been one of the prominent copper producers of the State, and until the opening up of the copper schist deposits in the neighboring mines of Miami, was responsible for the greater part of the copper output from the Globe district. As the gradual exhaustion of its orebodies near the surface led to the downward development of the mine, more water was encountered in the western portions directly underlying the dacite formation until the drainage problem became a serious factor in the operation of the mine and in the economical extraction of the ore. A heavy inrush of water on the 10th level of the mine in 1906, preceded by still earlier water difficulties, rendered imperative the immediate installation of a pumping equipment capable of handling large flows of water. While the Old Dominion has been recognized as a wet mine since its early days and one in which the complete control of the water situation was of paramount importance in the development of the lower levels, it is chiefly in the last nine years, since the installation of the increased pumping equipment, that the mine has developed and handled large quantities of water. Its maximum pumping record was reached in the first six months of 1915, during which time, following a prolonged period of abnormal precipitation, the pumps handled 1,624,740,000 gal. of water; while in the month of March alone, over 407,000,000 gal. of water were pumped from the mine.

Jan 1, 1917

By F. N. Rhines

STUDIES upon the sintering of metal powders, in the solid state, have led to the proposal that the surface energy of the powder particles provides the driving force that causes points of contact between pairs of particles to grow into broad welds which isolate the residual vacant space into pores that tend to spheroidize and gradually to diminish in total volume.' Investigators differ with regard to the mechanism of the movement of the metal, under the influence of surface energy, to accomplish these changes. One school asserts that there is a mass movement of the metal, referred to as a "viscous flow," while the other school prefers to view the movement as a self diffusion process, wherein individual atoms are, transferred without disturbance of the basic pattern of the crystal lattice. Extensive experimental studies upon the sintering of copper, conducted recently by A. J. Shaler,2 have been in- terpreted by their author as support for the viscous flow mechanism of transport, the theory of which was developed originally by J. Frenkel.3 Duplicating a portion of this work with minor changes, G. C. Kuczynski4 is led to the alternate view, namely, that the initial stages of sintering, at least, proceed as a self-diffusion process. Both of these investigations were designed to deal with an isolated unit of sintering, i.e., with the shrinkage of a single pore, or with the growth of a single point weld. It remains to ascertain the behavior of a typical metal powder compact composed of a large number of particles of varying size and sintering to a body with a multiplicity of pores. The observation of density changes alone during sintering is not sufficient in such a case; it is essential to know how the internal geometry of the compact changes. This has been the object of the present investigation, the results of which are used to support the self-diffusion mechanism of sintering. The present studies consist in the measurement of the number of pores as a function of size and time at temperature during the sintering of a copper compact made from a commercial copper powder lightly pressed and sintered in several different atmospheres. A brief survey was made also of the change in shape of the pores, under the influence of the same variables. All of this was done by direct observation with the microscope. Densities were measured on the same sample. It is found that, while the compact is exhibiting an overall shrink-

Jan 1, 1951

By John J. Croston

The year 1935 witnessed one of the world's oldest industries—gold mining—attain the stature of a billion dollar business. Preliminary estimates indicate that somewhat over 30,000,000 oz. of gold was produced, the largest output ever recorded and exceeding the previous year by more than 11 per cent. Of this huge total the Witwatersrand field produced about 10,800,000 oz., compared with 10,480,000 oz. in 1934. Russia was apparently the stellar performer, and from incomplete data it appears that between five and five and a half million ounces were produced by the Soviets compared with 4,200,000 last year and 2,814,000 in 1933. The United States nosed Canada out of third place with a production of 3,546,000 oz. against 2,916,000 in 1934, while Canada increased her total from 2,965,000 to 3,291,000 oz. Similarly, gains of lesser magnitude were made in Australia, the Gold Coast and other countries. As a result of great activity in developing outlying areas on the Rand, and the great number of new companies building mills in Canada, Australia, the Gold Coast and the United States, the years 1936 and 1937 should see new high records, as these new producers will more than offset any decline in the older properties. The whole world has become "gold conscious" during the past three years. It has been the subject of innumerable articles by economists and others, but, unfortunately, because of their lack of actual mining knowledge, they have treated the production of gold as a static affair, ignoring geological and technical factors. It is hardly necessary to draw attention to the fact that the world's gold-mining industry was slowly but steadily shrinking in importance, owing to the gradual depletion of known deposits that were profitable to work at costs existing prior to 1929. The International Geological Congress at Pretoria and the League of Nations Committee drew attention to the estimates of the mining experts of the various governments predicting a steady falling off in world production. On the Rand there

Jan 1, 1937

By J. J. Demo

The effect of aluminum additions on the coating vale and corrosion resistance of Cr-Fe diffusiou coalings on a mild steel substvate has been studied. Aluminum additions up to 2 wt pct increase the chromium penetration rate while further additions retard it. The apparent cor$lict between these data and metallogyapkic ineasurements, which show a continuially increasing coaling thickness with aluminum addition, is discrissed. Compavisorz of corrosion resistance on the basis of equal thickness of tlre entire coating measured mnetal- ALTHOUGH ferrous metal articles are cheap and widely used, they are often quickly degraded by corrosion. To prevent or slow down the corrosion process, lographically is misleading; equal thickness of the cor-rosion-resistant portion of the coating is a bette.v basis of conzpavison. Inter difision coefFicients for Cr-Al-Fe coatings of different aluminum content have been detevmined and found to dary logarithmically when plotted againnst chromium concentvation. A general method of calculating diffusion profiles for different lrealment limes and surfuce coucentralions IS described. many types of coating are applied to steel.' Among these are diffusion coatings, formed by high-temperature diffusion of selected elements into the surface, which then becomes the coating Diffusion coatings are metallurgically bonded to the substrate and show a continuously varying concentration gradient from surface to substrate. Generally, these coatings have the advantage of adhering to the substrate upon deformation of the composite. Moreover, when chromium is one of the diffusion elements, a mild steel substrate

Jan 1, 1968

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By D. K. Crampton

INTERNAL stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A résumé of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking: Certain agents, particularly mercurous salts, mercuric salts and ammonia salts; have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alphabeta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe 'limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper describes the field opeturluns at the Fry in situ combustion project in Crawford County, 111. Field operations may be divided into three phases—-preliminary engineering studies of 1960 and 1961, ignition, and, finally, operation of the test. The Fry combustion project was a pilot test of cocur-rent in situ combustion on a 3.3-acre inverted five-spot. In the summer of 1960, air injection tests were conducted using old wells in the area and a new air injection well drilled especially for the test. In the summer of 1961, four new oil wells were drilled on a 3.3-acre pattern for the pilot test. All old wells in the near vicinity of the pilot test were abandoned to preclude any possibility of gas escaping to adjacent formations. A compressor plant was also installed at the test site in 1961. Air injection tests and other engineering studies were made. At the conclusion of these tests, ignition was accomplished with a 40 kw electrical igniter. Operation of the Fry combustion test was little different from the usual oilfield operation with the exception of the high rate of air injection. No difficulty was found with the openhole completion. There were no unusual corrosion or emulsion problems until bottom-hole temperatures exceeded 150F. Four cores were drilled into the burned-out portion of the reservoir with no mechanical difficulties. INTRODUCTION A cocurrent or conventional in situ combustion test was conducted on the Fry unit of the Marathon Oil Co., in Crawford County, Ill. Besides testing combustion in the Fry type of reservoir, the test was intended to evaluate various operating procedures. This paper presents a discussion of the Fry combustion test field operations. The geology of the reservoir and the test performance are discussed in other papers.'.' HISTORY OF THE FRY UNIT The Fry unit consists of 11 leases totaling 337 acres in an area in which oil was originally discovered in 1906. Production from this reservoir, as from all Robinson sand reservoirs in the area, was very high during the first few years. As the dissolved-gas energy was dissipated, early attempts to retard the decline consisted of vacuum, air, and gas repressuring, and recently, most of the area has been subjected to water flooding. Following early air repressuring, the Fry waterflood unit was formed and water flooding initiated in July, 1952. In the area in which the Fry combustion test was conducted, a peripheral water flood of a 160-acre area was developed as shown in Fig. 1. Between 1956 and 1960, it became apparent that the water flood was unsuccessfd. In looking for a suitable site for an in situ combustion test, the Marathon Oil Co. selected the Fry unit as possessing those features most desirable for such a research project. Field operations associated with the Fry combustion test began in the spring of 1960.

Jan 1, 1966