Search Documents

By R. L. Dalton, L. A. Rapoport, C. W. Carpenter

Procedures have been developed to study the performance characteristics of unconfined pilot water floods using scaled laboratory models. The effects of operating conditions on pilot performance for variozrs well patterns have been investigated. The limitations of the laboratory model studies are outlined. Relationships between the oil recoveries of pilots and large-scale floods have been established. The applications of model studies to the prediction of large-scale waterflood performance and pilot flood design are discussed. INTRODUCTION Pilot water floods are undertaken to evaluate operational procedures and to gain advance information about the performance of an extensive water flood. In general, however, the performance of a pilot flood is not directly indicative of what can be expected from a large-scale pattern water flood. This difference stems from the fact that the over-all flow configurations are not the same for the two systems. A water flood normally consists of an array of identical well patterns. In such an array, the perimeters of the well patterns are axes of symmetry and act as impermeable boundaries. Thus, an extensive, pattern water flood can be visualized as a repetition of "confined" floods. In contrast, a pilot water flood involving only one or a few well patterns is "unconfined". Here the well patterns are not balanced by other flood units; hence, the perimeter of the pilot area does not act as an effective boundary. Accordingly, only a portion of the fluids injected (and also of those originally contained within the pilot area) is captured by the producers of the pilot. The rest escapes into the surrounding reservoir. This usually causes the amounts of oil and water produced in the pilot to be different from those recovered by a producer in an extensive water flood. Moreover, the recovery observed in the pilot can be expected to be greatly influenced by operating conditions, i.e., by the bottom-hole pressures at the injection and producing wells. The above considerations show that full utilization of pilot test results and reliable prediction of large- scale water floods require a knowledge of the relationship between the recovery performance of confined and unconfined well patterns. To date, only limited basic information is available on the behavior of pilot water floods. Craig, et al,' have investigated the effects of initial gas saturation, oil-to-water mobility ratio, and well damage on the oil recovered from a single, "normal" five-spot pilot pattern (Fig. 1). Rosenbaum and Matthews2 studied the effect of initial gas saturation and mobility ratio on the ratio of production rate to injection rate for various groupings of five-spot patterns. Paulse113 investigated the effect of mobility ratio and distance from the pilot to the edge of the reservoir on the areal sweep in a single "inverted" five-spot (Fig. 1). However, none of these studies considered the effect of operating conditions on pilot flood behavior. Moreover, hardly any of the work to date dealt explicitly with the oil-recovery performance of the pilot floods. The purpose of this paper is to introduce the concept of interrelation between pilot flood behavior and operating conditions, to illustrate this interrelation by means of experimental data and to compare the recovery performances of dif-

By C. Bezemer, I. Havenaar

An investigation was carried out on the dynamic liltration behavior of drilling fluids. In a set-up consisting of a porous pipe through which the drilling mud was circulated, dynamic liltration rates and cake thicknesses were determined as a function of flow rate and filtration time. Eventually, a state of equilibrium was reached; i.e., both cake thickness and filtration rate attained constant values. Concurrently, dynamic filtration tests were carried out in a simple dynamic filter apparatus where mud flow was similar to that in a rotational vismmeter. In both arrangements the relation between equilibrium liltration data and rate of shear at the cake surlace was studied. Filter pipe and dynamic filter apparatus were lound to give identical relations. It was therelore concluded that the latter apparatus, which is suitable lor routine measurements on small amounts of mud, could be used to determine the dynamic liltration behavior of mud under borehole flow conditions. Some data are presented on the effect of filtration pressure and temperature on equilibrium filtration rate and cake thickness. INTRODUCTION In oil well drilling, the drilling fluid used generally forms a mud cake on the permeable sections of the borehole wall while filtrate is lost into the formation. As to the conditions under which this filtration process takes place, a distinction should be made between static mud filtration (mud is not circulating) and dynamic mud filtration (mud is circulating). In recent years several investigatorsl-5 have studied the process of dynamic mud filtration about which little had previously been known. This type of filtration is the subject of this paper which confirms several findings of previous investigators. It differs from already published works, however, in the following respects. 1. It contains a description of a simple laboratory apparatus developed for dynamic filtration measurements on small amounts of mud. 2. The effect of rate of shear at the cake surface on dynamic filtration has been studied. As a result of this study, dynamic filtration data pertaining to the borehole conditions of mud flow can be found from laboratory tests. 3. Some data are presented on the effect of filtration pressure and temperature on dynamic filtration. The work was limited to a small number of muds. No attempt was made to compare data on API filtrare loss with dynamic filtration rates. Previous workers have clearly shown that no correlation exists between static and dynamic filtration rates. EXPERIMENTAL ARRANGEMENT To establish whether the effect of mud flow conditions on dynamic filtrations is governed by the rate of shear at the cake surface, two different types of mud flow were used. In this connection the experiments were partially conducted by means of a porous pipe through which mud was circulated, partly in a dynamic filter apparatus which somewhat resembles a rotational viscometer. In both cases the flow conditions of the mud were well defined, thus making it possible to-calculate rates of shear at the cake surface. The filter pipe was 200 cm long with an internal diameter of 3 cm. Its perforated wall was covered on the inside with filter cloth on which the mud cake could form. Mud was pumped through the pipe at linear rates varying from 20 to 186 cm/sec. The required filtration pressure was obtained by means of a lack-pressure valve downstream of the filter pipe. In this arrangement the type of flow existing in the borehole is reasonably well simulated. The dynamic filter apparatus (Figs. I. and 2) consists mainly of two concentric cylinders with a clearance of about 0.5 cm. The outer cylinder (rotor) can be rotated at rates up to 1,000 rpm. The outer surface of the inner cylinder (radius about 2.5 cm) is covered with filter cloth or paper supported by copper gauze. The two cylinders are mounted inside a pressure

Jan 1, 1967

By H. M. Howe

I WISH to present to you a few thoughts on some of the phenomena and laws of iron smelting. Owing to the great complexity of the subject, to the great variety of points to be taken into consideration, many of which are very poorly understood, and to the meagreness and even conflictoriness of our information with regard to some of the most important laws which govern the subject, the fruits of such thoughts as I venture to offer you must be received as speculations, not as facts. Nevertheless, in discussing old phenomena from new standpoints, thus furnishing a metallurgical parallax, if I may say so, these theoretical speculations may have their value in helping to a clearer comprehension of the phenomena and laws we now know, and in suggesting new lines of inquiry. While an increase of height in blast furnaces is not always followed by increase in their power of production, experience proves that it tends to increase it; for while we have many cases of short furnaces producing more iron than longer ones, yet enormous productions, such as those of the Lucy and Isabella furnaces of Pittsburgh, and of the furnaces of Esch sur l'Alzette, in Luxembourg, have never been reached in short furnaces. We may safely infer that height is an element essential to great production, though of course not the only essential element, and that, in the case of high furnaces which are not capable of great production, some other essential element is wanting. Moreover, experience teaches that within limits increase of height tends to increase the producing power in a still higher ratio. Thus, in the Esch furnace, which is 19.8 meters (65 feet) high, 393 tonnes (or 387 gross tons) of 312 per cent. Ore

Jan 1, 1877

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By J. Fred Johnson

COROMANT is the trade name of the alloy-steel drill rod tipped with a chisel-type tungsten-carbide bit manufactured by Sandvik Steel Works Co., Ltd. Other names, such as Swedish or air-leg method of drilling, are used in various localities. Coromant drilling in Sweden was the natural sequence of the adaptation of tungsten-carbide inserts to the already established routine of drilling. By the middle thirties the percussion drill had reached practically its highest attainable efficiency as a drilling machine. Since then improvement has been in metallurgy of component parts to increase life or lessen weight, in the development of pneumatic and automatic feeds, in the use of jumbos to more quickly and easily handle machines, and in changes in drill rods and bits. By 1937, drilling in the United States and Canada was done by relatively heavy mounted drifters with positive hand or automatic feeds. In Sweden, on the other hand, emphasis had been placed on light equipment and drifting was done with pneumatic bars and reverse-feed stopers. In 1938, one of the most prominent American drill manufacturers developed an air-leg for successfully drilling the extremely variable but relatively soft iron ores of some of the northern Michigan mines. Also in 1938, a comparative Swedish test, also in soft iron ore, of a 50-lb jackhammer mounted on an air-leg, against a 100-lb reverse-feed drifter on a pneumatic bar, showed the net drilling time was increased by the air-leg set-up from 51 to 71 pct, in drilling 6-ft rounds in a 6 1/2x6 1/2 ft drift. Miners were becoming scarce in Sweden even at that time and, since the lighter equipment made the work easier and more attractive, the airleg was then made use of in some types of soft rock. In 1940, for instance, a large tunnel for a hydroelectric plant was driven with this equipment. By 1943, when tungsten-carbide inserts came into the picture in Sweden, a great many of the kinks in percussion drilling with this hard-metal had been worked out in Germany under the stress of war conditions. However, only 10 pct of the drilling machines manufactured in Sweden were jackhammers for use on air-legs and only the one manufacturer made air-legs in the United States. American practice had largely supplanted integral forging of drill bits by the detachable steel bit. Canada and South Africa were using the one-pass throwaway bit but Sweden was still using the same old integral forged bit. After a long study of the trend toward simplicity

Jan 1, 1952

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Feb. 10, 1918, to Mar 10, 1918. ADKINSON, HENRY M., Min. Engr Walker Bank Bldg., Salt Lake City, Utah. BARKE, A. C., Min. Engr., United States Smelt., Refin. & Min. Exploration Co., 1503 Hobart, Bldg., San Francisco, Cal. BARKER, F. L., Prof. of Min. and Geol., Pei Yang University, Tientsin, China. BEASLEY, ALFRED F., Supt. Of Refinery, Bunker Hill & Sullivan Min. & Cone. Co., Kellogg, Idaho. BEEKLY, A. L Chief Geol., Cosden & Co., Tulsa, Okla. BELLIS, ARTHUR E Met., N. E. Westinghouse Co., Springfield, Mass. BRAIN, ELMER C Mgr., United Gold. Min. Co., Granite, Ore. BRUNER, CRANE S., Engr., American Zinc, Lead & Smelting Co., Carterville, Mo. COLLINS,. HARRY R Mech. Engr., Fuller Engineering Co., Allentown, Pa. CRANKSHAW, ALDEN, Experimental Met., New Jersey Zinc Co. (of Pa.), Palmerton, Pa. GALLIGAN, EMMET F., Mine Supt., Homestead-Iron Dyke Mines Co., Inc., Homestead, Ore. GREENE, FRANK C Geol., Cosden Oil & Gas .Co., Tulsa, Okla. HALSEY, HOWARD G Field Engr., 0. M. Bilharz Min. Co., Miami, Okla. HARROUN, DOUGLASS HOUGHTON, Supt.., Aguascalientes Metal Co., Asientos, Aguascalientes, Mexico.

Jan 4, 1918

By John D. Wiebmer

There are those in the Colstrip, Mont., area who can still remember the opening of the Rosebud mine in 1923. For 35 years it was a steady employer of 80 or 90 residents who produced coal for the railroad. In 1958, though, mining ceased as diesel locomotives supplanted steam engines. The mine was purchased in 1959 by Montana Power, the parent of Western Energy Co., and production resumed in 1968. Long Construction Co. was chosen as operator of the mine equipment. At that time, reserves appeared virtually unlimited. The thick Rosebud seam coursed through alternate sections of railroad holdings and federal land-then came the federal moratorium on coal leasing in 1971. About the time Western Energy completed the special leasing procedure to extend reserves from an existing mine, a new federal monkey wrench was thrown into the works with passage of the Surface Mining Control and Reclamation Act of 1977.

Jan 12, 1979

By S. F. Shaw

IN 1913, the Tiro General mine, at Charcas, S.L.P., Mexico, which had been making from 125 to 150 gal. of water per min., was allowed to become flooded, after all the pumps had been removed, and in 1918 the problem of unwatering it came up for solution. There are two vertical shafts, the Tiro General, 1390 ft., and the San Fernando, 1225 ft. in depth, with five connecting levels between them. The San Fernando shaft had been partly retimbered, while the Tiro General had been newly timbered from the collar to, 1090 ft. in depth. It had been possible to place guides in only one compartment of the Tiro General, from the collar to the seventh or 850-ft. level, to which it was necessary to lower the water before station pumps could be installed. Soundings indicated that compartments in the Tiro General were open to 1082 and 428 ft., and in the San Fernando shaft to 471, 488, and 586 ft. The water had risen to a point 140 ft. below the collar of the Tiro General shaft. PUMPING EQUIPMENT The steam plant at the Tiro General shaft includes one 300-hp., one 150-hp. and one 100-hp. Erie City water-tube boiler, and two 160-hp. Heine water-tube boilers. All but one of these boilers were supposed to be in good shape, but it was soon discovered that six years of idleness in a climate that is foggy for several months of the year had left them in poor condition. The compressed-air plant comprises one Nordberg cross-compound compressor with piston displacement of approximately 2500 cu. ft. of free air compressed to 96 lb. per sq. in.; and another Nordberg cross-compound with piston displacement of 1235 cu. ft. of free air, to the same pressure.

Jan 2, 1920

By George S. Evans

CERTAIN American operators believe that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphurization will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Paul E. Dorr, Kenneth P. Pavlich

This paper covers the practical aspects of economic analysis of mineral ventures and the application of a publicly available computer program. The paper touches briefly on the time value of money concepts and the phases of project evaluation. The most comprehensive port ion of the paper deal s with the requirements for economic evaluation, including capital expenditure categories, operating expenses, required geological and engineering data, and tax considerations. Highlights of the 1981 and 1982 tax laws are covered. A case study using the MINECO computer program will be used to illustrate the economic evaluation concepts developed. Guidelines and goals of sensitivity analysis and Monte Carlo simulation will be discussed and demonstrated on the MINECO example. The MINECO software system will be displayed as an example of a "user-friendly", interactive, and flexible computer tool available to the mining professional today.

Jan 1, 1983

Jan 1, 1969

By Van Der Muelen P. A.

SOME time ago, the writer received from W. 0. Borcherdt, Manager of the, works of the Bertha Mineral Co. at Austinville, Va., several specimens of a dense yellowish slag-like material, containing cavities showing clear needle-like crystals, and representing a product formed by the fumes of zinc oxide and basic lead sulphate from the oxide furnace, attacking the firebrick lining of the flues. The matrix, which is of a greenish-yellow color, is made up chiefly of an amorphous glass, carrying numerous crystals, the latter being well-defined, clear, and transparent, but colored a very light yellow by small amounts of ferric oxide. A number of the crystals were carefully separated from the matrix and tested with the blowpipe. They have a fusibility of about 2, yield a globule of lead and a coating of lead oxide before the blowpipe on charcoal, and contain some zinc. Their hardness is 5 to 6. 1 Fig. 1. Under the microscope the crystals appear to be made up of a prism, with narrow faces, and a fairly large pinacoid, but unfortunately show no terminal faces (Fig. 1). Between crossed nicols they gave parallel extinction in. the three planes containing the crystallographic axes, and are therefore orthorhombic. The index of refraction is high. A number of the best crystals were measured on the reflection goniometer, the angles given below representing the average of measurements made on different individuals. mm = 46° 52' mb = 66° 34' a:b:c = 0.4334:1 :?

Jan 5, 1917

ALTHOUGH everybody is familiar with coal, few persons have an exact idea of, the great impor-tance of this precious fuel. Coal is the black bread of industry. Without it, industrial activity is much restrained; and so the great industrial countries of Europe and the United States of America are the great producers of coal. The 1913 production of coal in Belgium was 22,842,-000 tons, valued at 418,700,000 fr., nearly a half billion. In 1919, it was 18,483,000 tons, about 81 per cent. of the production before the war; in 1920, it had reached 22,414,000 tons, approximately the production before the war. To show the importance of coal production of Belgium, let us say that the coal industry employed 168,000 workers in the year of 1920, the metallurgical industry only 129,000 and the textile industry 103,000. The coal industry, then, employs the greatest number of workers. The value of the coal production in 1919 is estimated at 1,121,000,000 fr. On the basis of the production before the war, the value of the production of iron in 1919 would have been 701,000,000, of finished steel 1,086,000,000, and of zinc 415,000,000; therefore, in 1919 the value of the coal industry was greater than that of the metallurgical production.

Jan 8, 1922

By W. A. LaVenue, W. M. Houston

Pebble phosphate mines of Florida have been established from south of Hardee County to north of the Georgia state line, a distance of over 200 miles. Mining has been carried out on an ever-increasing scale since 1885, but phosphate deposits that can be mined on the economical standards of today, are confined in a roughly circular area about 30 miles in diameter, generally within Polk and Hillsborough Counties, in the central part of the State. The phosphate deposit, which is in the Bone Valley formation of Pliocene age, is covered by Pleistocene terrace deposits of unconsolidated quartz sand. The matrix is composed of approximately 1/3 clay slimes, 1/3 silica sand and 1/3 phosphate pebbles. The phosphate usually occurs as rounded pebbles, ranging in size from about 1 in. down to approximately 400 mesh. The phosphate may vary from well-defined hard pebbles to soft weathered rock. The color and character of the phosphate will range from smooth buff pebbles to black and white "salt-and- pepper rock." The screen size distribution varies considerably between locations; the recoverable phosphate may extend down to the 400-mesh size in some areas, while in others the phosphate may cut off sharply at about 35 mesh.

Jan 11, 1962

By C. P. Fiske

The pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers, and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance come the condensers, as large numbers are used in the manufacture of spelter, and improvements in quality result in material decreases in working cost. While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are conccrned. Materials Bond Clay.—The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather it in the accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later) accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons with the clay as usually handled.

Jan 1, 1918

By C. E. Nelson

The purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. Types oF Melting Practice All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.2 The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be ' parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drying out or thickening after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to be poured out directly into castings without fear of flux contamination. This flux is not

Jan 1, 1944

By H. T. Matson

IN the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals.. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. Those interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.1

Jan 1, 1930