Search Documents

AS IS evident from the discussion in previous chapters, the methods by which an open-hearth heat may be made are numerous, but any heat, in the ingot form, may be classified as one of three types, depending upon the degree of deoxidation to which the metal is subjected. These are rimmed, semikilled, and killed, and desirable ingot structures, from the standpoint of distribution of porosity, are illustrated in Fig. 63. These are the most useful types of ingot structure [ ] and represent three stages in the continuous series from "wild" to "dead killed" (see Fig. 23, page 46) ; some of the variations of each type are discussed later in the chapter. The choice of ingot structure and of finishing practice used to produce the desired metal action in the molds is determined by consideration of: 1. Specified final analysis. As an example, the production of rimmed steels is mostly limited to carbon contents below 0.30 per cent and manganese contents below 0.60 per cent; on the other hand the production of low-carbon killed steel requires greater care.

Jan 1, 1944

The finding of gold, in enriching quantity, along the streams that issued from the western foothills of the Sierra Nevada was the prelude not only to the birth of an organized mining industry in California but to the intensive exploration of the entire Pacific slope; it presaged the feverish exploitation of the mineral resources that the ubiquitous prospector soon uncovered all over our western domain. At first when this migration began, as typified by the rush of 1849, there was no time to examine the signs of ore that were to be detected along the track of adventure, and, it must be added, not many in that motley crowd of gold-seekers were qualified to interpret the signs if they had lingered to look at them. Such intelligent curiosity as a few of them possessed was directed to the finding of gold chiefly, if not exclusively; and their good sense in this respect can not be impugned, because in a new and remote country the less valuable metals and minerals are unlikely to be worth the winning. Many of those that came to California crossed the alkaline wastes and sagebrush prairies that extend between the Great Sal? Lake and the ramparts of the snow-clad Sierra; when coming overland they found it convenient to halt on the eastern slope and to pitch their camp in the valley of the Car- son river before they began the tedious ascent of the mountains and the final entry into the land of gold. One of the trails most used by these immigrants followed the Carson river to the mountain meadows south of Lake Tahoe and then descended among the pine-woods of Placerville, where they went to work with pan and shovel in the gold-bearing streams

Jan 1, 1932

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

By Francis S. Kendorski

Caving offers the lowest cost per ton of ally large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently-taken on new importance as deeper, lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface mining methods, and too low grade to support any type of underground mining except a bulk method such as caving.

Jan 6, 1978

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900

By Duane H. Haley

The century we live in has been an eventful time for the Third World, particularly the country of Peru. Although it will take one or two generations more to see its end and fully evaluate its scope, it is already clear that during the twentieth century, Peru has entered a dynamic industrial, economic, social, and political revolution. This century has seen the end of old governments, and the introduction of reforms which radically change complex traditional patterns. It also has marked the beginning of an era in which the government has elected to undertake, as a national effort, most of the future economic growth of Peru. For the most part, large multinational mining companies, which have helped to discover and put into operation large mineral and ore deposits in Peru, have been sympathetic toward this philosophy. Most big foreign companies, in addition to capital, brought with them to Peru an efficient technology, modern management, and an effective organization for the further processing, sales, and distribution of refined commodities. Nationalization of all basic resources, including mining, is the, trend-not, it is hoped, to the detriment of established technology and production.

Jan 1, 1974

By Charles O. Burgess

The improvement in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. Material Tested Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250" C. (2282" F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown in Table 1, test 2. A small amount of copper was present in heat C of this series. Further data on the effect of chromium on strength were obtained from a third series of 13 cupola heats containing from 0.06 to 0.50 per cent chromium and made without steel additions. The heats were all

Jan 1, 1933

By E. N. Doyle

Since the mid-1930's a number of plants, using the principles of heavy media separation, have been installed throughout the world. In cases involving lead, zinc or lead-zinc ores the reasons for the choice of this type of beneficiation process have fallen into four major categories: A) The economic recovery of additional distinctly separate products, such as dolomite limestone at the Mascot Plant (1) of the American Zinc Co., and the ferrosilicon produced by St. Joseph Lead Company. (2) B) The elimination of a large portion of run-of-the-mine ore prior to grinding and flotation, to allow increased throughput with low capital cost. Examples of this approach are the Levante and Ponente plants of the Montevecchio Company in Italy (3) and the frequent choice of the Sink-Float process by the Penarroya Company of Paris. C) The processing of a sedimentary deposit, in which the valuable mineral is contained in the matrix separating the boulders, as was the case at the St. Joseph Lead Company plant at Haydon Creek (4) and also at Bunker Hill Mining and Smelting, Kellogg, Idaho. D) The simplification of Around support programs in mines by allowing greater freedom of action in the extractive pattern. An example of this choice is Cominco’s Sullivan plant which came into being as part of an extensive proposal to update the mining, crushing, transportation, grinding and beneficiation processes. (5)

Jan 1, 1970

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By L. D. Jaffe, J. H. Hollomon

THE effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained on tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By R. J. Watson

In an earlier paper, Ehrenburg and Watson1 published the develop ment for a potential function by which it is possible to obtain the electric potential at points on the surface of the ground when a current I passes between two electrodes and the subsoil is composed of parallel, homogeneous layers. In view of the continued interest in the resistivity method of electrical prospecting, the author has considered it desirable to publish the results of a number of theoretical studies making use of this potential function, and also the results of a considerable number of tests with models designed to show the soundness of the mathematical theory. It is hoped that these results will prove how erroneous the various empirical rules for depth determination may be. It has always seemed puzzling to the author that one can find, in papers published comparatively recently, statements upholding empirical rules for depth determination, and attributing most of the irregularities of resistivity curves to vertical discontinuities in resistivity in the subsoil. It would indeed be fortunate for the geophysical investigator if such a simple rule held. However, numerous investigators have proved both theoretically and by the success of their field work that such a rule does not hold, even by a "rough approximation" in many cases. On the other hand, as is shown in the development to follow, if the underground conditions are favorable it is possible for such empirical rules to give a satisfactory depth determination. Authors should be more careful about making such sweeping statements about the accuracy of these empirical rules because the relative simplicity of the field work places the method in the hands of any interested experimenter, and he is likely to become completely disgusted with the method after he has made several obviously wrong interpretations by empirical rules. There are simple and rapid methods for finding out whether the ground beneath the electrodes is sufficiently similar to the conditions

Jan 1, 1934

By C. W. Washburne

Recently, Messrs, Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these. Messrs. Mills and Wells show that the composition of the deep brines oi the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paperJ2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended from a deep, possibly intratellurie, source. Messrs. Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3 for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at all times, because it always is in contact with the interstitial water of enclosing shales and of the sandstone. Experimental studies of soil moisture have shown that approxi-

Jan 1, 1921

By Howard Scott

Invar is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100" C. and soon reaches the value of copper. Guillaumel met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detrimental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

[Abrahamson, Guy C., (5'43) Lt., 0-880861, Hammer Field Fresno Calif. Adamec, LAW, (8'42) c/o Braden Copper Co., Rancagua, Chile. Adams, Karl S., (9'43) Univ. of New Hampshire, Durham, N. H. Agnilar, Roperto Q., (9'43) Texas College of Mines, El Paso Texas. Ainge, B'onald Farra, (943) Otago University, Dunedin, New Zealand. Akaran, Cevdet A,, (9'44) Pennsylvania State College, State College, Pa. Albala, Americo, (5'44) School of Mineral Industries, The Pennsylvania State College, State College, PA.]

Jan 1, 1946

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction .within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress.4,5? The theory of recrystallization is not in advanced state; if recrystallization data were obtained, in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By John D. Sullivan

Leaching of copper ores is a comparatively old art, probably dating back to medieval times. The leaching of mixed oxidized-sulfide ores, however, is modern. The first modern plant leaching mixed ores was at Ajo, Ariz., where commercial operations commenced in 1917. While the ore at Ajo was primarily oxidized there was always some sulfide present. The Inspiration leaching plant, which was put in operation in 1926, may be considered the first plant constructed for the extraction of both sulfide and oxidized copper. The pioneers in leaching mixed ores had a difficult task before them since they had very little fundamental data on the chemical and physical factors of leaching. For the very large amount of painstaking experimental work that was done before building the Ajo and Inspiration leaching plants the reader is referred to the original articles.' For a period of several years the writer worked on problems connected with the chemistry and physics of leaching mixed oxidized-sulfide ores. This paper summarizes the experimental work and discusses various factors involved in leaching ores. It also presents many data heretofore unpublished. Among the new data are those on chrysocolla, pages 518 to 519, inclusive; dioptase, page 519; covellite, page 529; virtually all those on chalcopyrite, pages 531 to 533, inclusive; enargite, page 533; and tetrahedrite and tennantite, pages 534 and 533. The oxidized copper minerals of commercial importance in American ores are azurite, Cu3(OH)2(CO3)2; malachite, Cu2(OH)2CO3; chrysocolla, CuSi03.2H2O; tenorite (or melaconite), CuO; and cuprite, Cu2O. Dioptase, CuSiO3.H2O is less common. Brochantite, CuSO4.3Cu(OH)2, while the chief mineral in the ore at Chuquicamata, is not of major importance in the United States. Metallic copper, while chemically not so, is frequently classed as an oxidized mineral of copper. The most important sulfide minerals are chalcocite, Cu2s; covellite, CuS; bornite, Cu5FeS4; and chalcopyrite, CuFeS2. Less important complex sulfides are enargite,

Jan 1, 1934

By Roland Blanchard

ABSTRACT RECENT discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Race-course) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalcopyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show [ACCEPTED ZONAL SUCCESSION Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite MOUNT ISA SUCCESSION Chalcopyrite In the main but Silver sulphantimonides wholly Tetrahedriteably not Galenacontemporaneous Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silverlead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1495 ft.). The anomalous condition at Mount Isa, both as to the unorthodox mineral succession and the largely unorthodox pattern of mineral distribution, is explained in the present paper,

Jan 1, 1943

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 1, 1950

PRESIDENTS DAVID THOMAS 1871 Born November 3, 1794, Cadoxtan, Glamorganshire, South Wales. Died in 1882. Attended schools in Wales. Came to America in 1839. A.I.M.E.: Member, 1871; Honorary Member. Iron manufacturer; inventor. Built first anthracite fired hot-blast furnace in America. Known as the "Father of the Lehigh Valley." President, Catasauqua and Fogelsville Railroad; Director, Lehigh Valley Railroad; Founder, Thomas Iron Co. and St. Luke's Hospital at Bethlehem, Pa.; Trustee, Lafayette College.4 ROSSITER WORTHINGTON RAYMOND 1872-1874 Born April 27, 1840, Cincinnati, Ohio. Died in 1918. Brooklyn Polytechnic Institute, 1857; Lafayette College, Ph.D., 1868; Lehigh University, LL.D., 1906; University of Pittsburgh, Hon. LL.D., 1915., Gold Medal, Institution of Mining and Metallurgy (London). A.I.M.E.: Founder, Member of 1871; Vice President, 1871, 1876-1877; Secretary, 1884-1911; Secretary Emeritus, 1911-1918; Honorary Member. Consul¬ing mining engineer; practicing lawyer, sailor, soldier, writer, orator, editor, theologian, teacher, novelist, chess player. Recognized as the "Grand Old Man of the Institute." ALEXANDER LYMAN HOLI,EY 1875 Born July 20, 1832, Lakeville, Conn. Died in 1882. Brown University, 1853; Hon. LL.D., 1878. A.I.M.E.: Member, 1871; Vice President, 1874; Manager, 1877-1879. Bessemer Medal (Iron and Steel Institute, London), posthumously. Brought bessemer process to United States. A statue was erected in Washington Square in his memory and presented to the City of New York in 1889. The inscription notes: "foremost among those whose genius and energy established in America and improved throughout the world the manufacture of bessemer steel." ABRAM STEVENS HEWITT 1876 Born July 31, 1822, Haverstraw, N. Y. Died in 1903. Columbia University, 1842; Hon. LL.D., 1887. A.I.M.E.: Member, 1871; Manager, 1872-1875. Bessemer Medalist and Honorary Member, Iron and Steel Institute (London). Gold Medal, Chamber of Commerce of New York City. Philanthropist, lawyer, statesman, publicist, pioneer in the iron and steel industry. Mayor of New York City in 1887. Business partner of Peter Cooper, Executive Manager of Board of Trustees, Cooper Union, New York City.

Jan 1, 1947