Search Documents

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.' A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By David S. Bolin

INTRODUCTION This paper is directed toward those companies or individuals who may be considering the possibility of tin exploration or development projects in South America. Although tin deposits are known in many countries of Latin-America including Argentina, Peru, and Mexico, the majority of the deposits are located in Bolivia and Brazil. These two countries also account for virtually all the current production. Many factors affect the economic decisions related to mining and exploration projects in this region including the following: 1) Types of deposits 2) Anticipated size and grade of deposits 3) Deposit geometry and ore distribution as it affects the selection of a mining method 4) Metallurgical amenability 5) Governmental policies 6) Taxation 7) Anticipated capital and operating costs 8) Marketing costs This discussion will be directed toward each of these points. The majority of the presentation will be concentrated on Bolivia as this country is the principal producer in the region, however, the potential for further tin development in Brazil is excellent. Due to the remote and previously almost inaccessible location of the stanniferous districts of Brazil, little is known with respect to size and type of non-alluvial deposits which may exist in this vast country. TYPES OF DEPOSITS Two major types of deposits are currently being exploited in Bolivia; alluvial, and hard rock or lode deposits. Bolivia produces substantial tin from both types of deposit whereas virtually all Brazilian production to date has been from alluvial sources. Alluvial Deposits Brazil: The alluvial tin deposits of Brazil are located in river channels and flood plains adjacent to low mountain ranges. The terrain containing the tin placers is flat, marshy, and generally jungle covered. The major controls of alluvial cassiterite concentration are the ancient and present stream channels. The average tin concentration in the placers varies from 500 grams to approximately 1.0 kilograms per cubic meter. Tin reserves in the Rondonia field of Brazil have been estimated at 600,000 tons of fine tin. A bucketwheel suction dredge went into production in the Rondonia district in 1979, and four others have since been ordered. Several other gravel pump, and hand mining operations are also in production in this field. In addition to the Rondonia district, tin occurrences are known from Xingu, in Para state, and in the state of Minas Gerais. Bolivia: The alluvial deposits of Bolivia are somewhat more complex due to the variable geomorphology and abrupt topography. Conventional placer accumulations of cassiterite are found in many stream channels and intermontane basins surrounding the major lode tin producing regions. In addition to stream and valley placers, a group of deposits locally referred to as "Pallacos" or "Llamperas" which consist of colluvium, landslide debris and glacial moraine material, contain substantial tin reserves in some areas. The stream channel and intermontane basins contain the only deposits which are presently being exploited by mechanized methods. One dredge is working the stream channel below Cerro Rico de Potosi and another is operating in an intermontane basin southeast of the city of Oruro. Both of these dredges are operated by private companies. The average grade for these operations varies from 250 to 500 grams per cubic meter. The largest of the intermontane basin placers known at present is the Centenario deposit located adjacent to the Catavi lode deposit. This deposit contains approximately 170 million cubic meters of material with an average grade of about 150 grams per cubic meter. The "Pallacos" deposits are found on the slopes of mineralized areas and in glacial moraine. The mineralized material is generally completely unsorted, with tin and sometimes tungsten values distributed erratically throughout the entire mass. Most of these deposits are worked by small leasors or cooperatives; however, at least one mechanized washing plant is in operation southeast of Oruro. The size of these deposits may reach up to several million cubic yards. Grades are very erratic, but may range from 200 to 500 grams per cubic yard. In addition to the formal mining operations, virtually every drainage surrounding the major mines is being worked by independent' miners utilizing hand mining and jig or pan concentration. The aggregate production from these operations is substantial. The

Jan 1, 1982

By T. K. Perkins, L. R. Kern

A study of fluid mechanics, rupture of brittle materials and the theory of elastic deformation of rocks shows that, for a given formation, crack width is essentially controlled by fluid pressure drop in the fracture. Operating conditions which cause high pressure drop along the crack (such as high injection rate and viscous fluids) will result in relatively wide cracks. Conversely, operating conditions which cause low pressure drop (low injection rates and thin fluids) will result in relatively narrow cracks. Charts and equations have been derived which permit the estimation of fracture widths for a variety of flow conditions and for both horizontal and vertical fractures. INTRODUCTION There has been considerable speculation concerning the geometry of hydraulically created fractures in the earth's crust. One of the questions of practical importance is the width of fractures under dynamic conditions, i.e., while the fracture is being created and extended. Such width information could be used, for instance, to help estimate the area of a fracture generated under various conditions. Also, there has been a recent trend toward the use of large propping partiles.13, 15 Therefore is is desirable to know what factors can be varied in order to assure entry of the large particles into the fracture. There has been some work on fracture widths reported in the literature. In particular, there have been several Russian publications dealing with this sub-jeCt.1.31,3 These papers have dealt principally with the elastic theory and the application of this theory to hydraulic fractures. These studies have not led to an engineering method for estimating fracture widths under dynamic conditions. A recent paper3 has reviewed and summarized the Russian concepts. An earlier paper- from our laboratories also discussed the application of the elastic theory to hydraulic fractures. This first approach, based largely on photoelastic studies, has proved to be too simplified to accurately describe the fracturing process. However, these early thoughts have served as a guide during the development of more exact concepts. We would like to present in this paper our current concepts regarding fracture widths and some estimates of hydraulic fracture widths for several conditions. We believe that it is now possible to predict with fair accuracy the factors influencing fracture widths. Furthermore, the method of prediction has been reduced to a simple and convenient graphical or numerical calculation. CRACKS IN A BRITTLE, ELASTIC MATERIAL Many investigators2, 4, 30 have shown that competent rocks behave elastically over some range of stresses. Of course, if the tensile stress imposed upon a rock exceeds some limiting value, then the rock will fail in tension. In similar manner, there are some limiting shear stresses that can be imposed upon rocks. Hubbert and Willis11 have discussed the shear conditions which will lead to failure. Under moderate stress conditions (such as those likely to be encountered when hydraulically fracturing) and when stresses are rapidly applied, relatively, most rocks will fail in a brittle manner. Hence, for this discussion of hydraulic fractures in the earth's crust, we assume the rocks behave as brittle, elastic materials. Let us develop the discussion in the following way. (The following thoughts are applicable only to brittle materials.) 1. First we consider a brittle, elastic system. An energy balance will show the minimum pressure necessary to fracture rock, and from this pressure we calculate the minimum crack width resulting from extension of a hydraulic fracture. 2. Then we will show that, under ordinary fracturing conditions, fracture widths are appreciably greater than the minimum widths of extending fractures. In fact, we will find that crack width is controlled by fluid pressure drop in the fracture. 3. We will discuss pressure drops in fractures and resulting crack widths for various operating conditions and both vertical and horizontal fractures. 4. Finally, we will discuss the significance of these concepts, their relationship to fracturing pressures, etc. First, consider minimum fracture extension pressures. We can shed some light on this question by considering the theory proposed by Griffith7, 8 Yo explain the rupture of brittle, elastic materials. Griffith recognized that solid materials exhibit a surface energy8 (similar to surface tension in a liquid). The fundamental concept of the Griffith theory is that, when cracks spread without the application of external work (in the interior of an elastic medium which is stressed

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By Jun Hino, P. G. Shewmon, P. A. Beck

THE investigations of Crussard,' of Guinier and Tennevin,' and of Dunn and Daniels," indicate that the subgrains formed in a cold worked and annealed metal are capable of growing at each other's expense during annealing, if the temperature of annealing is sufficiently high and the time is long enough. The results of Dunn and Daniels are particularly convincing in showing that subgrain growth is essentially the result of the free surface energy associated with the subboundaries. In subgrain growth, as in ordinary grain growth, energy is gained as a result of the decrease in total subboundary surface area per unit volume. Recently, Wood and Scrutton4 found that the rate of subgrain growth upon annealing increased very considerably, if simultaneously a creep strain was applied to the specimen at a low strain rate. Working with 99.98 pct pure fine-grained aluminum, these investigators found that the continuous X-ray diffraction back-reflection rings of material strained at room temperature remained continuous after heating for ten days at 250 °C. However, when heated at the same temperature under a stress of 1000 psi even for only three days, the formerly continuous X-ray diffraction rings broke up into numerous dots, which were fairly clearly separated from each other. The continuous X-ray diffraction rings were interpreted as indications of a very small subgrain size, not resolved by the X-ray diffraction method used. The breaking up of the continuous X-ray diffraction ring during annealing under stress was taken as an indication of a great increase in subgrain size, so that the individual subgrains could then be resolved. The effect of simultaneous strain at a low strain rate in accelerating subgrain growth, discovered by Wood and Scrutton and designated by them as "cell growth," is of fundamental importance. The experiments described in this note were carried out in order to confirm Wood and Scrutton's results by direct metallographic observation. Also, information was sought as to the minimum creep strain necessary to produce this effect. A fine grained high purity aluminum strip was prepared by alternate 33 pct rolling and annealing treatments for 1 hr at 350°C. Specimens cut from this strip were subjected to a relatively fast creep strain of 7.2 pct in 3.5 min at 300°C under a constant load initially corresponding to 1185 psi. The subgrains set up were large enough (about 0.015 to 0.03 mm) to be clearly observed (Fig. 1) at X200 magnification with polarized light, after electrolytic polishing and anodic etching, producing a fine oxide film." The corresponding X-ray diffraction pattern is shown in Fig. la. After the fast creep strain treatment a portion of the specimen was subjected to a creep strain of 8.3 pct in 44 hr at 350°C under a constant load initially corresponding to 320 psi. Another portion, annealed under the same conditions, but not strained, served as control specimen. The subgrain size of a typical area of the specimen annealed under strain and of the one annealed without strain is shown in Figs. 2 and 3 (X-ray diffraction patterns, Figs. 2a and 3a). Annealing without strain produced clearly observable subgrain growth (subgrain size: about 0.03 to 0.05 mm). The effect of simultaneous strain was to increase greatly the rate of subgrain growth (resulting in a subgrain size of approximately 0.05 to 0.13 mm), in accordance with Wood and Scrutton. In another experiment, the effect of the amount of simultaneous strain was studied. The initial subgrain structure was set up by fast creep, as described previously. The specimen was then heated at 350 °C under a constant load initially corresponding to 320 psi, as above, for 2.2 hr (0.24 pct strain), and 8.8 hr (0.58 pct strain). Comparison with the corresponding unstrained control specimens by means of X-ray diffraction showed that 0.58 pct strain definitely had an effect, but the effect of 0.24 pct strain was doubtful.

Jan 1, 1953

By D. Turnbull, J. H. Hollomon

THERE is a large body of evidence'" indicating that solidification during the liquid-solid transition is usually induced by heterogeneities present in the liquid. By dispersing liquid metals into small droplets, the impurities responsible for catalyzing solidification are isolated within a small number of these droplets. The effect of the foreign body therefore is restricted to a single drop by this technique. Thus upon cooling below the melting temperature, solidification is initiated by homogeneous nucleation in the majority of the droplets that do not contain impurities. In the case of solidification of liquid metals, the activation energy for nucleation is so great that its rate changes by orders of magnitude for a change in temperature of only several degrees centigrade.' Effectively homogeneous nucleation occurs at a critical temperature upon continuous cooling. Thus by microscopic observation of single particles during cooling, a temperature at which the rate of homogeneous nucleation becomes sensible can be determined.3 since at the temperatures at which nucleation occurs in the absence of impurities the rate of crystal growth is extremely rapid, the temperature at which the entire particle solidifies is very nearly the temperature at which the nucleation of the solidification occurs. Thus for liquids that freeze at high temperatures the onset of nucleation can be established by simply observing the temperature at which the marked heat evolution and increase in brightness of the particle occur. For liquids that freeze at lower temperatures the onset of nucleation can be determined by a rumpling and change in shape of the particle resulting from its solidification. The microscopic technique for observing the solidification of small particles has already been described." In earlier papers the nucleation of solidification of pure metals 5,6 and of alloy systems7 showing complete liquid and solid solubility have been described. In the present paper, the observations are extended to a simple eutectic system (Pb-Sn) where the possibility of the formation of two solid phases exists. Metals for the investigation were obtained from the American Smelting and Refining Co. in the form of pure lead and pure tin, 99.8 and 99.9 pct purity, respectively. An ingot of each of the pure metals was made into shot by heating the metals at a temperature about 50 °C in excess of the melting point and pouring the liquid slowly into a container of water at 15°C. Samples of the shotted pure metals were weighed out to make alloys containing 5, 10, 15, 20, 25, 30, 40, 50, 60, 70, 80, and 90 atomic pct Pb. Samples of each alloy were then melted in separate beakers. Each melt was poured through a pyrex funnel into a cylindrical mold (% in. ID). The casting solidified in 10 to 20 sec. The inside of the mold as well as the funnel through which the metal was poured were coated with graphite to eliminate adherence of the metal. Analyses were performed on some of the compositions and are given in Table I. The compositions also were checked for these samples and for those that were not analyzed by determining the spread between the liquidus and the solidus upon melting the small metal particles. These measurements agreed as well with the nominal compositions as the analyses listed above. Results The results of the supercooling experiments for the several alloys are summarized in Table II and plotted on the constitution diagram in Fig. 1. Data for the pure lead and pure tin were taken from earlier investigations. The values for the maximum supercooling of the several alloys are the average of several determinations on a number of drops of each alloy. The maximum value in any determination was within about 2 pct of the average. For the alloys containing from 20 to 60 atomic pct Sn, inclusive, two marked changes of the surface structure were observed upon cooling. At the higher temperature, after the first appearance of the solid phase it continued to grow slowly at a constant temperature and then stopped. At the lower temperature the alteration of surface structure was abrupt. For the alloys containing from 70 to 95 atomic pct Sn, inclusive, an abrupt change in surface structure was observed at a single critical temperature.

Jan 1, 1952

By R. B. Full

DURING the summer of 1949, the United Nations Scientific Conference on the Conservation and Utilization of Resources met at Lake Success. As summed up by one writer, the purpose was: "That everyone will try to learn how to feed more people from an acre of land." That objective is a stimulus to the phosphate rock industry as well as other industries. Phosphate rock was mined first in the Canadian province of Quebec where it was found as an apatite in pockets. In 1863, mining began near the Rideau Canal, first in open trenches and quarries until shafts were sunk. These operations were difficult since hard rock had to be drilled and blasted. Steam was the source of power. The phosphate rock was hand-selected and recovery ranged from 6 to 10 pct, averaging 70 pct to 85 pct bpl (bone phosphate of lime). Costs, f.O.b. Montreal, were $14 a ton, and selling prices averaged $17 a ton. In 1885, about 29,-000 tons were sold on this basis, but by 1892 the output fell to 8000 tons at an average price of $15 a ton at Montreal. South Carolina Deposits Phosphate rock was first discovered in South Carolina in 1837, but a mining company was not formed until 1867. It was immediately successful, and the industry continued to develop and ship an increased tonnage of land and river rock, shipments increasing from approximately 20,000 tons in 1868 to 537,000 tons in 1890, when the shipments began to decrease. In 1892 only 350,000 tons were shipped. In this field there were two types of deposits: land rock and river rock. More land rock tonnage was mined until about 1887 when river rock production began to equal it. The land rock was mined adjacent to and in the river marshes by pick, shovel, and wheelbarrow. Each worker dug daily a space 6 ft wide, 15 ft long and 6 ft deep, which was overburden, and then loaded about 3 cu yd of phosphate rock into wheelbarrows. His helper would wheel the barrows to small steam railroads up to 250 ft distant. Water was kept from the pits by steam pumps connected to railway cars. The phosphate rock was loaded into railroad cars, hauled and dumped into a log washer to which water was added, and run over trommel screens to eliminate the clay and loose sand. Steam shovels for loading were introduced about 1891. River rock was mined by floating dipper dredges and at low tide was loaded into barges by laborers using oyster tongs, the large lumps being hand-loaded. Barges and bateaus were unloaded by wheelbarrows which were wheeled to the same type of land rock washers. The washer product was piled with stacked pine cordwood in alternate layers and fired for drying. Usually this was done under sheds along the river bank. The dried rock then was transferred to ships, usually three or four-masted schooners. Cost of production of both land and river rock, including $1 a ton royalty paid to the state for state-owned property, was approximately $4.25 a ton averaging 60 pct bpl. The selling price was approximately $7 a ton f.O.b. In 1886 the courts handed down a decision permitting anyone to mine, and many additional companies were organized immediately. As a result, the selling price was lowered to a profit margin of 50Ø or less per ton. The South Carolina mines were eventually shut down when a more profitable source of phosphate rock was discovered in Florida. Florida Deposits Phosphate rock was discovered in Florida in 1882, and in 1883 a small quarry was opened near Hawthorne. In 1886 phosphate rock of good grade was discovered on Peace River, and the Arcadia Phosphate Co. was formed. In 1888 the company began shipments amounting to 3000 tons that year. During the latter part of 1888, hard-rock phosphate was discovered near Dunnellon. Exploration extended rapidly, and deposits of hard-rock phosphate were mined over a wide area so that shortly after 1900

Jan 1, 1952

By Peter Beardmore, Michael B. Bever

The effects of the temperature of deformation and the degvee of deformation on the annealing spectrum of a Au-Ag alloy have been determined by vesistance measurements. Specimens were deformed in torsion at 4°, 78K and room temperature up to strains nd/l of about 1.0 and were isochronally annealed. Discrete annealing stages similar to those found for pure metals were observed. Stage A occurred below room temperature; the decrease in reszstance associated with this stage increased as the temperature of deformation was lowered or the strain was increased. Stage B manifested itself as an increase in resistance; this is attributed to the restoration of short-range order promoted by vacancy or vacancy aggregate migration. At temperatures above 48S0K, recrystallization or Stage C occurred. Stages A, B, and C in the annealzng curves of this alloy may be considered to correspond to Stages II, Ill, and V, respectively, in the terminology used to describe the annealing spectrum of pure metals. ThE annealing behavior after deformation below room temperature has been thoroughly investigated on pure metals, in particular gold and copper. The occurrence of several discrete stages in the annealing spectrum of these metals has been established, but the interpretation of some of these stages in terms of specific mechanisms is still controversial.' The annealing of alloys deformed below room temperature has been the subject of only a few investigations. In the investigation reported here, a Au-Ag alloy was annealed after deformation at and below room temperature. This continues a research program on the deformation and annealing behavior of Au-Ag alloys.2-8s EXPERIMENTAL PROCEDURE An alloy rod of composition 82.6 wt pct Au-17.4 pct Ag was reduced to wire, 0.0428 in. diam, by swaging and drawing. After a recrystallization treatment, the grain size was 0.031 mm, as obtained from the average linear intercept.7 The ends of wires about 6 in. long were flattened and sealed into short brass tubes with cold setting cement to form the grips of the torsion specimens. The equipment used for deformation has been described elsewhere.6 The specimens were deformed at room temperature, 78", and 4°K to various strains nd/l, where n is the number of turns, d the diameter of the specimen, and 1 its length between grips. The strain rate ?max was 0.1 min-' at the sur- face of the specimen except where noted otherwise. The specimens were annealed isochronally for 30 min at intervals of approximately 30°K from the temperature of deformation to approximately 800°K, except that after deformation at 4°K the lowest annealing temperature was 78°K. A potentiometric method was used to measure the resistance: all measurements were made at 78°K with the exception of some measurements at 4°K mentioned below. Data obtained with a single specimen yielded a complete annealing curve: in several cases duplicate specimens were used to confirm the reproducibility of the curves. Since the surfaces of the specimens were rough after deformation, their diameters could not be measured accurately. The resistance increments after deformation and annealing are therefore reported as percentages of the resistance of the same specimen measured after completion of the annealing, that is, after full recrystallization. The corresponding resistivity values can be calculated by obtaining the effective diameter of a deformed specimen from the ratio of its resistance after recrystallization to the true resistivity, which was determined with a smooth specimen of known dimensions. This method of calculation was used to obtain data shown in several of the figures. RESULTS AND DISCUSSION The isochronal annealing curves after deformation to various strains at 4", 78K, and room temperature are shown in Figs. 1, 2, and 3, respectively. The resistance increment of the as-deformed specimens as a function of strain is shown in Fig. 4. For the specimens deformed at 4°K. values measured at 78°K are plotted with the exception of those for the as-deformed

Jan 1, 1970

By H. E. Swanson

A description of the field apparatus has been published by D. G. Brubaker. Data from laboratory model studies of the in-line and broadside methods of operation are detailed. The conductor models include a single sheet conductor at several strike and dip angles and a schistose-type conductor. In addition, data on the effects of the strike length and of the depth of the conductor are presented for the broadside method of operation. All of the data show that the inclintion reverses direction over the top edge of dipping single sheet conductors. Differences between anomalies over conductors dipping between 90" and 30" are subtle,but flat-lying sheets can be readily distinguished from steeply dipping sheets. Schistose conductors are easily distinguished from single sheet conductors, and a procedure is given for determing the direction of schistosity. The depth of penetration under ideal conditions is 0.7 of the coil separation. In 1950, The New Jersey Zinc Co. (of Pa.) developed a lightweight apparatus for electromagnetic prospecting. A description of this apparatus has been published by D. G. Brubaker.1 It consists of a small, battery-powered vertical source coil and a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station the inclination of the magnetic field created by the source is measured. Two methods of operation are used, in each of which measurements are taken with a constant source-to-receiver distance and with the plane of the source oriented to pass through the receiver station. In one procedure, called the in-line method, source and receiver travel in tandem along the same line. In the other procedure, called the broadside method, source and receiver move along adjacent lines, with the source-to-receiver direction oriented parallel to the assumed strike direction. The data recorded in either case are the inclinations, measured in degrees from the horizontal, of the magnetic field created by the source. These data are plotted at the receiver stations on a map. Scale-model studies of both methods of operation have been conducted in the laboratory and are reported in this paper. APPARATUS Small source and receiving coils wound with many turns of fine copper wire were used to produce and measure an alternating magnetic field in the same manner as the field apparatus. The model source coil was mounted in a vertical position and oriented so that the receiving coil was in the plane of the source. The receiving coil was mounted in a frame so it could be rotated to obtain the inclination measurements. The source coil was excited by a 100-kc signal generator. A tuned amplifier and a voltmeter were used to detect the null position of the receiving coil. The coils used in the field apparatus are usually spaced about 400 ft. The coils used in the model work were spaced from 4 in. to 4 ft apart. Thus the scale of the model work ranges between 1/1200 to 1/100 natural size. The model conductors were aluminum-coated building paper supported on wooden frames. The conductivity-thickness product was measured using a four-electrode system and was found to be about 300 ohms-'. CONDUCTIVITY CONSIDERATIONS The electromagnetic response from a thin sheet conductor is a function of the product of the conductivity of the sheet times the thickness of the sheet times the frequency of the alternating electromagnetic field times some linear dimension of the system such as the coil separation which indicates scale. The secondary electromagnetic field produced by the conductor increases in amplitude from zero at zero conductivity to a maximum value for infinite conductivity, while the phase of the secondary field with respect to the primary field shifts from 90" at zero conductivity to 0" at infinite conductivity. Several authors2-' have shown that most of both the increase in amplitude and the change in phase of the secondary field takes place over a three-decade range of the conductivity-thickness-frequency product. Only small changes in the amplitude and

Jan 1, 1961

By Margaret V. Doyle, R. W. Powers

INTERNAL friction measurements, carried out as functions of temperature, have been used extensively to obtain data on the mobility of interstitial impurities in the Group V metals, vanadium, colum-bium, and tantalum. For a given frequency of vibration, the internal friction peaks at a temperature which depends principally on the particular metal and interstitial impurity. Relaxation times and corresponding activation energies are determined from a knowledge of such peak temperatures for various vibration frequencies. These experimentally determined relaxation times are related to the average jump frequencies of the interstitial impurity atoms using the model of Snoek1 and can be related to macroscopic diffusion coefficients as shown by Polder.2 In these Group V elements, the impurity whose diffusion rate has been the hardest to pin down by the internal friction technique has been carbon. The experimental difficulties associated with carbon in these metals were not evident in the earliest investigation carried out by Ke on tantalum.3 The carbon peak was thought to occur near 140°C at 1 cps on the basis of the enhancement of the height of this peak measured on specimens which had been coated with colloidal carbon and heated in vacuo at 1200°C. Presumably on the basis of similar evidence, Wert identified a peak also near 140°C at 1 cps in columbium with the diffusion of carbon in that element." Later, the difficulties of admitting carbon into these metals without simultaneously introducing oxygen were pointed out by Ang and Wert- nd by Marx, Baker, and Sivertsen.6 The latter suggested that the peaks attributed to carbon in tantalum and columbium might arise from the presence of traces of oxygen, adventitiously absorbed during the carburization. Such suspicion was confirmed, at least in tantalum, when it was found possible to prepare C-Ta specimens without contamination by oxygen. Specimens sci prepared, aitnough high in carbon content, gave no evidence of a damping peak near 140°C.7 Recently, the authors were able to Show that carbon diffuses in tantalum at a rate only slightly slower than that for nitrogen.8 At 1 cps, the carbon peak lies at 34g °C, only a few degrees above the nitrogen peak at 341 °C. However, the two could be distinguished by a different stability with respect to aging at 400 °C and by a different dependence of peak height on solute concentration. On the basis of this experience with tantalum, it appeared worthwhile to search also for a carbon peak in columbium in the vicinity of the nitrogen peak." In this report, the location of the carbon peak in columbium is made known and its position relative to the nitrogen peak is compared with the authors' previous findings in tantalum. In addition, a second source of internal friction seen only in specimens of very high purity is discussed. Columbium was obtained from the Fansteel Metallurgical Corp. as either 30 or 40 mil diam stock. The manufacturer gives the following analysis as typical of this material: 99.4 pct minimum Cb, 0.10 pct maximum C, 0.5 pct Ta, 0.04 pct Ti, 0.02 pct maximum Si, and 0.01 pct maximum Fe. Wires 13 in. long were degassed near 2200°C for 4 to 16 hr in an ultimate vacuum better than 2.10" mm Hg in an apparatus described previously.8 This treatment reduced the oxygen and nitrogen damping peaks observed in the as-received material to less than 0.0001 in Q-1 above background. The latter value varied somewhat from specimen to specimen in the range 0.0004 to 0.0008, depending chiefly on the wire diameter and the frequency of vibration. The high temperature evacuation left the specimen in a rather soft condition, the Vhn being reduced to 40 from a value near 121 in the as-received conGi~iur~. The gram size was about the diameter of the specimen. After outgassing, specimens were loaded with carbon by absorption of such hydracarbons as methane or ethylene. Carbon was also added to a few speclrnens by heating them at

Jan 1, 1958

By R. E. Ogilvie, E. T. Peters

The X-ray Kossel-line method has been used preaioz~sly for measuring lattice parameters to accuracies of 1 part in 100,000.5 A second application of this method is described for determining the crystallographic orientation of a randomly positioned single-crysta1 spherical volume that can he as small as 50 µ in diameter, within accuracy limits of ±1/2 deg. The theory, experimental procedure, and interpretation of Kossel-line patterns and an experimenta1 verification of the predicted orientation relationship of the cph k and fee a Cu-Si phases are presented. This orientation relationship can be described as (111)a, (00.1)k; [110]a [11.0]k. In addition, the lattice parameter of the a phase was found to he a. = 3.62154 ± 0.00014Å. The Kossel-line method when used in conjunction with electron microanalysis is shown to he capable of providing a complete chemical and structural analysis of a given crystal. THE most easily accomplished methods for determining the orientation of a single crystal are variations of the Laue X-ray diffraction method. Although certain materials can be oriented to within ± 1 deg accuracy by observation of exterior macroscopic features, such as etch pits, cleavage faces, or growth features, the Laue method is generally preferred for routine laboratory application. Both back-reflection and transmission patterns are coordinated by appropriate reference charts and are plotted in terms of reflection plane poles (normals) on a stereographic projection. Orientation is deduced by relating the pole distribution (which is fixed by the crystallographic symmetry of the specimen) to two specified external reference directions. The Laue method has several limitations. 1) Orientation can rarely be determined to better than ±l deg accuracy. Principal errors involve inaccuracy in specimen-to-film distance, measurement confidence of individual Laue spots, and stereographic plotting. 2) Because of the indeterminacy of the X-ray wave length diffracted to a given spot, it is not possible to determine supplementary crystallographic data, such as interplanar spacings and lattice parameters. 3) The method is generally limited to specimens of cubic symmetry or to specimens of high symmetry and known structure. 4) The relatively large cross-sectional area of the incident X-ray beam generally precludes the measurement of relative grain orientation in a polycrystalline material.* _____ Several of these limitations can be overcome by application of the Kossel-line method, which has been previously employed for precision lattice-parameter determinations.'-= For this method, a point source of divergent monochromatic X-rays is generated within the crystal by means of an incident electron beam. The divergent X-rays which fulfill the Bragg law are diffracted by the specimen and are recorded on a film placed either in transmission or back reflection. Analysis of the film yields a direct measurement of orientation and lattice-spacing values to an accuracy of ±1/2 pct. As analyses can be obtained from spherical specimen volumes as small as 50 µ in diameter, the method provides a means for structural analysis of second-phase or impurity precipitates within a given matrix. The primary limitation of the Kossel-line method is the requirement for an electron microanalyzer or similar apparatus capable of producing a finely focused electron beam. This paper is designed to present the theory, experimental procedure, and geometrical interpretation of Kossel patterns. The experimentally determined orientation relationship between the k and a phases occurring in the Cu-Si system and a precision measurement of the a lattice parameter are presented as a practical application of the method. THEORY OF KOSSEL LINES Divergent X-ray beam photography utilizes an effective point source of characteristic X-rays which, when diffracted from a single crystal, form numerous diffraction and absorption cones that are recorded on film.7 The cones generated from a source lying within the crystal are called Kossel lines.' Although the X-ray scattering from a divergent point source contained within a crystal is described in terms of Laue dynamical theory,9 the directions of the diffracted spectra can be ade-

Jan 1, 1965

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By P. R. Gage, R. W. Bartlett

At high temperatues and reduced oxygen pressuves, molybdenum silicicles oxidize to form SiO(g) vathev than a passivating SiO2 film. This is a sevious problem for low-pressure applications of sili-cide-coated rejvactory tnetals. As oxiclalion pvoceeds, the higher oxidntion potential of silicon initially suppresses oxidation of molybdenum and silicon is depleted near the surface. Eventually, silicon depletion causes secondary passivation (SiO2) mid an active to passiue transition in oxidntion behavior at moderately low pressures. At very low pressures, silicon depletion continues until steady-state oxidation of both silicon and rnolyhdenum can proceed at rates propovtional to their initial stoicliiorrzetvies. Ohsel-vations of 'oxidatiou-rate belzcriliov at temperatures from 1101° to 1700°C and oxygen pressures from 10-7 to 1 at in were made using thermogravimetn'c, X-ray diffraction, and elect?*on-rtric?ro/,vobe techniqrres. The experimental results are in good agreement with calculated lirnits for the various types of behavior that were based on tlievtnochernicnl atzd dffusion rate data for the Mo-Si system. A protective oxide film normally forms during the oxidation of elemental silicon. However, at elevated temperatures and reduced pressures this film is not present and oxidation is rapid. wagnerl has shown that this behavior occurs because SiO(g) is more stable than SiO2. The behavior of the silicides at high temperatures is similar but more complicated. Molybdenum and several silicide compounds are involved and the chemical activity of silicon, or the equivalent silicon vapor pressure, can vary considerably in these phases. Also, diffusion in the silicides resulting from reactions in which a higher silicide is reduced to a lower silicide, or molybdenum containing dissolved silicon, must be considered. EXPERIMENTAL AND ANALYTICAL METHODS Isothermal oxidation experiments were conducted using hot-pressed MoSi2 and Mo5Si3 wafers. Each experiment was conducted at a fixed oxygen pressure by controlling the flow of oxygen in and out of the furnace chamber. Most of the experiments were conducted in a molybdenum-wound tube furnace. Special construction features, including use of a high-purity dense A12O3 refractory tube, permitted operation in high vacuum to 1500°C. Higher temperatures could be obtained at higher working pressures and with a sacrifice of tube lifetime. Temperature was measured with three Pt 6 pct Rh/Pt 30 pct Rh thermocouples and controlled with a proportional controller. Weight changes were monitored with a quartz spring balance. The few experiments, at higher temperatures and low pressures, were conducted in a cold wall vacuum chamber using induction heating with direct susceptance of the sample. Because of the variable levitation effect of the induction coil on the sample, weight changes could not be monitored continuously in these experiments. All samples representing both experimental methods were weighed before and after oxidiation and examined with a microscope and analyzed by X-ray diffraction. The analytical treatment assumes equilibrium at interfaces and uses existing thermodynamic data. For convenience, equilibria are expressed as chemical potentials or as vapor pressures of the gases involved. The resulting differences in equilibrium vapor pressure between adjacent interfaces and between the surface and external atmosphere drive diffusion processes in the solid and gas boundary film, respectively. These diffusion processes govern the rate of oxidation. A bibliography of the sources of thermochemical data for the reactions pertinent to the Mo-Si-O system is given in Table I. Reactions are listed with the sources of free-energy data referenced. Since all of these reactions involve one or more gas species, usually oxygen, a plot of the product-gas chemical potential, -RT In Pg, vs absolute temperature for each reaction is given in Fig. 1. These curves can be used to determine equilibrium vapor pressures or to compare the stability of different compounds in the various gases: O2, Si, SiO, and Moo3,. The data of Table I and Fig. 1 were used to determine the analytical results presented in this paper. EXPERIMENTAL RESULTS The weight changes for three MoSi, samples oxidized at 1500°C are plotted against time in Fig. 2. The treatments were identical except for the indicated variance of oxygen pressure and each curve represents one of three characteristic types of behavior that were observed. The upper curve is an example of passive oxidation, which is defined as

Jan 1, 1965

By V. G. Leak, R. A. Swalin

The dilhsion of silver and trace concentrations of tin in liquid silver has been rrzeasured in the temperature range from about 975° to 1350°C. The difBsion dala. fil lhe following equations: fov self-diffusion of silver The ratio of DSn to DAg is found to be about 1.34. The higher diffusivity of tin is interpreted in terms of the coullombic repulsion which results from the fact that tin dissolved in silver has a valence of +3 relative to silver. THE phenomenon of diffusion has been well-described theoretically for hard-sphere gases and solids and found to be in good agreement with experimental data for certain gases and solids. Liquid-diffusion phenomena have not been well described theoretically and there is generally a lack of good experimental data. In this investigation self-diffusion and solute diffusion in liquid silver were studied. Silver was chosen as a solvent for two main reasons. First, silver is a noble metal and the atoms are considered to have a spherically symmetric charge field; hence the liquid may be considered to be a random array of approximate hard spheres. Mercury, gallium, and other lower-melting metals were eliminated from consideration since it appears possible that in their liquid states there is some residual long-range order and directional bonding. Second, silver behaves as a monovalent solvent and, while cadmium, indium, tin, and antimony all have nearly the same atomic size, they have chemical valences relative to that of silver of +1, +2, + 3, and +4, respectively. Slifkin, Lazarus, and coworkers1-5 investigated the diffusion of these solutes in solid silver and found that their diffusion rates increased with an increase of the excess valence of the solute. In the solid state the diffusion-rate increase was calculated to be due to a change in local modulus of the solvent caused by the excess valence of the solute.1"3 For the present investigation it was planned to determine the effect of valence upon solute diffusion in liquid silver. It was deduced that a coulombic repulsion between solute and solvent might be responsible for larger volume fluctuations in the vicinity of the solute thereby enhancing the diffusion of the solute atoms. Tin was the first solute investigated and was chosen for experimental convenience. If an excess-valence diffusion effect exists in the liquid state, the solute tin with its excess valence of + 3 might show a large enough effect to distinguish it from the self-diffusion of silver in silver. The silver self-diffusion data were obviously required as a base line for comparison. In addition silver self-diffusion was investigated with a view toward examining the data in connection with the Sutherland- Einstein: Coheen-Turnbull,7 and swalin8 theories of diffusion in liquids. I) EXPERIMENTAL TECHNIQUES The diffusion coefficients for tin and silver in liquid silver were determined in separate experiments using the capillary-reservoir method of Anderson and saddingtono but following closely the experimental techniques outlined by Ma and Swa1in. The radioactive alloy bath was prepared by plating either tin-113 or silver-110 m isotope* onto 99.999 *Isotopes obtained from Oak Ridge National Laboratory. pct Ag rods.* The silver and isotope were melted *Silver obtained from Cominco Co. and mixed in a graphite crucible under a purified argon atmosphere, then outgassed for capillary filling. Some of the fused-silica capillaries were filled individually as reported by Ma and Swalin, but most were filled in a different manner. A long piece of capillary tubing was sealed off on one end and held in the system so that the open end was just above the surface of the molten alloy. The system was evacuated, the open end submerged into the alloy, and argon was admitted into the system up to atmospheric pressure. The molten alloy was forced up the capillary several inches where it solidified and was subsequently cut into segments of the proper length for diffusion annealing. The apparatus for diffusion annealing was the same as that used for capillary filling except that a Pt—Pt, 10 pct Rh therinocouple was placed in the solvent bath in order to accurately measure the temperature during the run. A diagram of the dif-

Jan 1, 1964