Search Documents

By M. W. Legatski, D. L. Katz

The best currently available description of the longitudinal mixing properties of a porous medium is an equation of the form which relates the effective longitudinal dispersion coefficient Dp to the molecular diffusion coefficient Do, the electrical resistivity factor F, the porosity <f> and a Peclet number. If the parameters dpa and m are determined for a porous medium of known porosity and electrical resistivity factor, then a dispersion coefficient may be estimated for a given flow rate and a given gas pair. A new method, featuring on-line gas analysis by thermal conductivity and on-line data reduction by analog computation, was developed and used to determine these mixing parameters for eight naturally occurring sandstones and two dolomite samples. The exponent m of the above equation was found to vary between 1.0 and 1.5. The characteristic length dpa in the above equation was found to vary between 0.25 and 1.9 cm, with an average value of 0.4 cm for sandstones. Measurements were made on two cores in which paraffin wax had been deposited by evaporation from a pentane solution. They indicated that the presence of an immobile phase such as connate water could increase the dispersion coefficients significantly. INTRODUCTION While the petroleum and chemical industries have studied the mixing of miscible liquids flowing in consolidated porous media and of miscible gases flowing in unconsolidated porous media, relatively little data have been presented to describe the mixing of gases flowing through consolidated porous media. Such data are of particular interest to the gas storage industry. For instance, the U. S. Bureau of Mines is storing large quantities of a rich helium-nitrogen gas in contact with a natural gas in a dolomite reservoir. Since the rich gas occupies only 15 percent of the total reservoir volume, it is essential that the extent of rich gas-natural gas mixing be predicted and understood as a function of rock properties, pressure and rate of movement. This investigation was concerned only with the determination of longitudinal dispersion coefficients. It is understood that a transverse dispersion coefficient, which characterizes mixing perpendicular to the direction of flow, may be an order of magnitude less than the coefficient characterizing mixing in the direction of bulk flow.5719 It should also be recognized that the use of any dispersion coefficient is in itself a simplification. It is necessary to assume that mixing in a porous medium may be characterized by the equation for flow in a single direction. A number of authors1 l8,19 have pursued the mixing problem, not in terms of the so-called "dispersion model" described by Eq. 1, but in terms of a "mixing cell model". This model supposes that a porous medium is constructed of a large number of small mixing chambers and that the concentration of the diffusing component within each mixing chamber is uniform. Fick&apos;s law (Eq. 1) assumes that there is no gross by-passing of one fluid by another, and that there are not stagnant pockets of gas in the system under consideration as discussed by Coats and Smith.8 These assumptions are not always valid for flow through porous media and it is important to recognize the limitations upon Eq. 1. The most serious limitation upon the assumption of Fick&apos;s law mixing in a porous medium is

By Julian Szekely

Through the simultaneous statement of Maxwell&apos;s equations. the turbulent Navier-Stokes equations and the differential thermal energy balance equation, a mathematical representation has been developed for heat transfer and fluid flow in electric arc furnaces. In broad outline the theoretical predictions appear to be consistent with experimental measurements. A discussion is presented of the general arc furnace control and optimization problem, together with the potential for the incorporation of the mathematical model given in the paper, into future control and optimization schemes. ELECTRIC ARC FURNACE STEELMAKING accounts for about 24% of the total steel produced in the U.S., consuming about 550kw-hr/ton of steel which amounts to about 1.4x1010 kw-hr annually. The percentage of steel produced by the electric arc furnace route has doubled since 1960 and is expected to increase further in the foreseeable future, particularly with the more extensive use of direct reduction technology. Table I shows, in terms of percentages, the principal items that contribute to the cost of running an electric arc furnace. It is seen that in addition to the fixed costs (labor, depreciation, taxes etc.) electrode costs and power consumption are the dominant inputs, and it follows that process changes that would ultimately reduce any of these cost components would have a significant impact on the efficiency of the operation. There are three main areas where progress in arc furnace design and operation must be directed in the next decade (Committee on Technology, 1981). 1. Increased furnace productivity 2. Reduction in processing cost 3. Improvement in the thermal efficiency of the furnace An estimate of the current operating efficiency of the electric arc furnaces may be obtained by comparing the theoretical minimum energy consumption per ton of steel with those achieved in operational practice. Theoretically 330-360 kw-hrs of electricity are required to melt one ton of cold scrap. For superheating, 8-12 kWh per 100°F are required. The actual energy requirements are given in Table II. It is seen that furnaces currently operate at 70-80% efficiency, with the major heat loss from the furnace resulting from the waste gases (Committee on Technology, 1981). While it is apparent that operational experience has produced a technology that is reasonably energy efficient this has been achieved in the almost complete absence of any detailed knowledge concerning the fundamental heat transfer mechanisms occuring in the furnace. The purpose of the present paper is to present a case for the usefulness of mathematical models in increasing the thermal efficiency of furnaces by investigating these heat transfer mechanisms and then combining this knowledge with existing electrode regulator mechanisms to produce truly efficient power cycles for melting and refining. In particular, existing mathematical models describing convection, radiation, and electro-magnetism in the furnace should be employed, and the development of optimization models which balance the cost of electrodes and energy against the thermal efficience of the furnace should be undertaken. Recent work in this laboratory (Szekely, McKelliget, 1981, 1982, 1983; Szekely, McKelliget, Choudhary, 1983) has made a useful start towards solving the problem of heat transfer within the electric arc furnace but the work still needs to be directly related to existing furnace power cycles and tested against plant scale measurements.

Jan 1, 1984

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.&apos; Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference &apos;R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z&apos; = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser&apos;s and Spretnak&apos;s treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors&apos; reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z&apos; = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg&apos;s X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

By W. L. Falke, A. A. Cochran

A basic problem in connection with manganese is to find economical ways to utilize domestic resources. As a part of its program to conserve domestic mineral resources and to reduce dependence of foreign sources, the Bureau of Mines had conducted extensive research to broaden manganese technology and to find economical, technically-feasible processes for recovering manganese from these low-grade resources. This paper analyzes some of the major difficulties which have been encountered in previously proposed processes for treating low-grade manganese ores and discusses a process which may circumvent many of these difficulties. Vast deposits of low-grade manganese ore exist in the U.S., yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.&apos; A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical, technically feasible processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.&apos; Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4 Chlorination processes have become increasingly useful as a means of recovering valuable metals from raw materials, because the relative cost of chlorine (Cl2) and hydrogen chloride (HC1) has decreased through the years, and because the corrosion resistance of materials of construction has been improved. The objective of these processes is to form metal chlorides that are more volatile or water-soluble than are the corresponding oxides or sulfides; these compounds then can be separated from the gangue or other minerals by volatilization or leaching. Several chlorination processes for the recovery of manganese have been investigated by the Bureau of Mines5-8 and others; the major chlorination processes were reviewed in 1963, and their main features were compared.4 In all these processes, the simultaneous leaching or volatilization of iron chlorides with manganese chloride (MnCl2) is a problem, and the more iron that is present, generally the greater the problem. The leaching step is not highly selective, and the product of this step is, at best, suitable only for the production of ferromanganese or for further processing to remove iron. The product of the volatilization step is, in all cases, a mixture of iron and manganese chlorides that contains too much iron even for ferromanganese production, and must undergo additional processing steps for iron removal. THERMODYNAMIC CONSIDERATIONS The literature indicates that the desired chlorination reactions will proceed at practical rates at temperatures near 1200°K (927°C). Free energy changes at 1200°K for the critical steps of the reduction and chlorination reactions9-11 follow: Most of the research on chlorination processes for manganese recovery has been done with HC1 rather than with C12, for the following three main reasons: 1) Recycling of the chlorinating agent, which is economically vital, appeared to be easier for HC1

Jan 1, 1968

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.&apos;s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain&apos;s paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales&apos; suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales&apos; paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey&apos;s program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain&apos;s paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales&apos; suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales&apos; paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey&apos;s program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Carters-ville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.&apos; With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2 The barite-producing part of the Cartersville district is relatively small, having from north to south a length of 4.5 miles, and a width of 2 miles. This small area, containing 35 barite mines, is the source of practically all of the barite produced in the state. The area is hilly, and has a total relief of 500 ft. The west-flowing Etowah River crosses the middle of the area, and is an unfailing source of water for operations on properties near its course. Opencut mining is carried on during the entire year, but is hampered by rain in the winter and early spring. Three railroads, two U.S. highways, and a network of graded roads provide access to and within the district, as well as excellent shipping facilities for ore and supplies. In addition to the barite, the district contains deposits of manganese, brown iron, ocher, umber, and specular hematite. Geologic Setting The area containing the barite deposits is underlain by Lower Cambrian rocks and their weathered residua. These rocks are grouped in three formations; in ascending order, these are the Weisner, the Shady, and the Rome. The Weisner formation consists mainly of finely micaceous metashale containing many random beds of quartzite, a few beds of conglomerate and metasiltstone, and beds of crystalline limestone that is apparently scarce. The formation is more than 1000 ft thick, and the base is not exposed. On account of their resistance to weathering, the rocks of the Weisner formation have sustained the higher elevations and therefore crop out on the ridges that characterize the area. Nearly all of these ridges are underlain by asymmetric anticlinal folds, and conversely the intervening valleys are underlain by synclinal folds. A diagrammatic section, showing typical mode of exposure of the Weisner rocks and their relation to overlying formations, in the limb of a fold, is shown in Fig 1. The Shady formation here consists of a lithologically distinctive series of variably siliceous specular hematite beds and thin beds of dolomite, which in places contain abundant fossils. In the zone of weathering, the dolomite has been leached and most of the hematite hydrated to ocherous and umber-ous clays, hut bedding planes in these weathered materials are commonly well preserved with or without distortion effected by slumping. This preservation of structure during weathering is lacking in the residuum that rests on the Rome dolomite, which is described below. The maximum thickness of the

Jan 1, 1950

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1&apos;2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900&apos; C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1&apos; and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969

By E. Breinan, M. Salkind

Al3Ni whiskers were chemically extracted from unidirectionally solidified Al-A13Ni eutectic ingots, bent into loops, and heated for 0.1 to 10 hr at 320°, 415", and 510°C. The initial strains ranged from 0.003 to 0.055. In all cases, permanent plastic deformation was noted after heat treatment. The deformation consisted of relatively uniform bending at low stresses and temperatures and short times and kinking followed by fracture at high stresses and temperatures and long times. After kinking, the whisker segments adjacent to the kinks were found to have straightened, which is evidence of a dislocation condensation mechanism. The range of temperatures and strains at which time dependent plastic deformation was found indicates that creep of whiskers probably plays a role in the creep of A13Ni whisker-reinforced aluminum. WHISKERS may be defined as nearly perfect single crystals which exhibit high strength. Because they can support high stresses at relatively low strains, they have been successfully employed in reinforcing metals at both ambient and elevated temperatures. In studying the creep behavior of A13Ni whisker-reinforced aluminum at elevated temperatures,1,2 it was noted that the composites exhibited measurable creep deformation. This investigation of the creep relaxation of individual A13Ni whiskel, extracted chemically from the composite was initiated to determine if creep of whiskers could con. "bute to the overall creep of the composite material. Many observations of plastic deformation of metal and halide whiskers have been made. Brenner3-8 noted that copper, silver, and iron whiskers exhibited heterogeneous plastic deformation at room temperature when strained beyond their yield points. Gyulai9 and Gordon10 observed plastic deformation of relatively large (>3 µ) NaCl and KC1 whiskers, although the smallest, most perfect whiskers were completely elastic. Eisner" noted plastic deformation and microcreep of iron and silicon whiskers at room temperature after straining beyond the yield point. Whiskers reported to exhibit creep at stresses below the yield point were zinc1&apos;-" and Silicon.15 Cabrera and price" observed some zinc whiskers which crept at room temperature after a short incubation period but then stopped creeping after a short time. Because some of their specimens exhibited no creep, they concluded that those whiskers that crept were relatively imperfect. Pearson, Reed, and Feldman15 observed similar creep behavior of silicon whiskers at 800°C. They also concluded that creep of the whiskers was a result of imperfections in their crystals. Brenner16 observed delayed failure of A12O3 whiskers at elevated temperatures but found no evidence of plastic deformation up to 2030°C (99 pct of E.EREINAN and M.SALKIND,JuniorMembers AIME,are Research Scientist and Chief, respectively, Advanced Metallurgy Section, United Aircraft Research Laboratories, East Hartford, Conn. Maunscript submitted April 5, 1968. IMD the melting temperature). Brenner also noted7 that some copper and iron whiskers exhibited delayed kinking above 350°C while others did not. One can conclude from these observations that small relatively perfect whiskers could exhibit completely elastic behavior during sustained elevated-temperature loading of composites. Since A13Ni whiskers tested in both bending and tension were found to exhibit no evidence of plastic deformation at room temperature&apos;7&apos;18 this study was initiated to determine whether or not creep of A13Ni whiskers occurred at the elevated temperatures at which creep in the composites was observed. Whiskers were chemically extracted from ingots of unidirectionally solidified A1-A13Ni eutectic, constrained in bending to various elastic strains and heat-treated. The bending constraints were removed after heat treatment and the amount of permanent set was taken as a measure of the time-dependent plastic deformation. EXPERIMENTAL PROCEDURES Ingots of eutectic Al-A13Ni containing nominally 6.2 wt pet Ni were unidirectionally solidified at approximately 11 cm per hr using a process described elsewhere.19,20 The starting materials were 99.99 pct pure. Cylindrical sections cut from the center of each ingot were placed in a 3 pct aqueous solution of hydrochloric acid and the whiskers were extracted as described previously.17 The whiskers nearest the surface were blackened somewhat due to overexposure to the acid while the center of the ingot was being dissolved These partially attacked whiskers were discarded. An intermediate zone of silver-gray-colored whiskers was collected and stored in methanol for use in relaxation experiments. Individual long pieces of A13Ni whiskers were placed on Fisher Precleaned Microscope Slides. These normally straight whiskers were bent elastically into arcs or loops of varying radii by manipulating their ends with a slender probe. The mass attraction between the whisker and the probe was sufficient to cause the whisker to follow the probe. The whiskers were retained in the elastic bend by the surface tension of a fine residual film on the slides. By using long whiskers, the action of the surface tension on the unlooped ends of the whisker allowed high elastic strains to be maintained in the loops. After each whisker was bent, a photomicrograph was taken for use in measuring the bending strain. The range of strains studied was 0.003 to 0.055. The bent whiskers were then encapsulated in Pyrex tubes at pressures between 10"6 and 5 x 10"6 mm of mercury and heat-treated at 320°, 415°, and 510°C (respectively 53, 61, and 70 pct of the peritectic decomposition temperature). After each heat treatment, the liquid film on the slides was found to have dried, but the whiskers were held in their original shapes by a residue on the slide. The minimum radius of curvature of each bent whisker was measured before and

Jan 1, 1969

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By N. F. Fiore, M. C. Mangalick

DISLOCATION damping in single crystals is orientation dependent.&apos; If dislocations are distributed uniformly over all the slip systems in a crystal, and if each dislocation contributes identically to the damping process, then a damping loss or decrement 6 arises. In fact, however, for a crystal of axial direction (hkl), dislocations on certain slip systems are oriented to make a larger contribution to the damping loss than are dislocations on other slip systems. Thus the measuring damping, 6 (hkl) is proportional to an orientation factor (hkl), which weights the ability of each slip system in the crystal to contribute to the total damping. If it is assumed that dislocations are distributed uniformly on all slip systems, then for a given orientation of an fcc crystal this factor is determined2,3 by the three nonzero elastic constants Cll, C12, and C44 and the density p. In this communication measured values of elastic constants for two Fe-18Cr-Ni alloys are reported, and the dislocation damping results on two different orientations of each alloy are analyzed for orientation dependence. Elastic constants were determined by measuring the ultrasonic velocities of one longitudinal and two shear waves in (110) direction of the fcc crystals.4 Variation of velocities with the change in orientation is very small for (110) orientation,3 and so this direction is ideal for orientation factor and comparative damping measurements. Experimental Procedures. The nominal compositions of the alloys studied are given in Table I. These alloys were vacuum-melted and vacuum-cast from high-purity materials at U.S. Steel Applied Research Laboratories. The single crystals were grown by the modified Bridgeman technique. The specimens were homogenized at 1350°C for 20 hr, cut to shape and size with a spark cutter, and then annealed at 1100°C for 20 hr prior to use. In the KHz frequency range, the Marx composite piezoelectric oscillator was used to obtain the damping. The ultrasonic pulse technique was used to measure the ultrasonic velocities and the attenuation in the MHz frequency range. M.c.mANGALICK,-- StudentMemberAIME,formerly Research Assistant, University of Notre Dame, is now with Casting Laboratory, Chase Brass and Copper Co., Cleveland, Ohio. N. F. FIORE, Associate Member AIME, is Assistant Professor, Department of Metallurgical Engineering and Materials Science. University of Notre Dame, Notre Dame, Ind. This communication is part of a Ph.D. thesis presented by M. C. MANGALICK to the Graduate School of the University of Notre Dame. Manuscript submitted May 20. 1968. IMD Elastic Constants. Table I gives the values of the ultrasonic velocities. Values of C11, C12, and C44 calculated from these velocities are also given in Table I, and it is evident that there is very little variation in C11, C12, and C44 with nickel content. This slight variation may be attributed to inaccuracies in velocity measurements and practical differences in the orientations of the specimens. For example, in B the time interval for vl was 2.4 ± 0.05 sec giving an error in v1 of 0.235 x or 0.005 in. per sec. The elastic constants obtained by pulse technique were tested by calculating E<110>, Young&apos;s modulus for the (110) direction, from the equation: This value was compared with the value computed from the resonance bar measurements in which where fr is the resonance frequency and I, is the length of the specimen. In all cases, the values calculated from the ultrasonic velocity measurements

Jan 1, 1969

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered arc&apos; those circumstances under which any company, including one that is cash rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON INVESTABLE CASH If you approach an individual with an investment which can be financed from savings, or by borrowing at a rate higher than one is earning on savings, that individual will quickly tell you that to pay interest at a rate higher than is being earned on savings would reduce overall income. Assuming that additional investment opportunities are not currently being considered, the individual concludes that a draw-down on savings, leaving a cushion for contingencies suited to individual circumstances, is the correct financial decision. For reasons discussed later, the simple mathematical logic leading to this conclusion tends to become obscured at the corporate level. When Leveraged Studies Are Inappropriate or Premature Surprisingly, I have heard of a number of companies that could afford to finance an investment solely with internal funds, which have made DCFROR (i.e. discounted-cash-flow rate-of-return) studies not only on a 100% equity basis but also on a leveraged basis. Certainly, a leveraged study would be appropriate if additional projects were competing for more capital than was available internally. Often, however, other projects are not far enough along to warrant a leveraged study and there is some danger that a project may be undertaken because it has an estimated acceptable rate of return, on a leveraged basis, that is not ultimately earned because some of the other projects are postponed or abandoned and borrowing is less than expected. For the above reasons, until it has been determined that (1) borrowing is a reasonable certainty for a particular project and (2) the timing and amount to be borrowed has been determined within a reasonable range of accuracy, I believe it is inappropriate and misleading to calculate DCFROR for a project other than on a 100% equity basis. Even when there are several projects currently competing for funds and borrowing will be required to finance one or more of them, using the common yardstick of calculating DCFROR on a 100% equity basis is a safer method to initially evaluate and compare the attractiveness of the projects. Many companies, whether they would have to borrow or not, will reject projects that on a 100% equity basis do not meet their minimum rate of return standards. Some companies which have to borrow will undertake a project provided the project&apos;s DCFROR on a leveraged basis meets its minimum return standards. The danger of this approach is that even moderate shrinkages of estimated cash flows could plunge return below

Jan 1, 1985

By H. M. Chance

Jan 1, 1887

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending up on the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper con- tent, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product. STANDARD SECTION EQUIPMENT With the old-flow sheet, a standard section consisted of four ball mills and classifiers, one air lift, 20 roughing tables, 10 cleaner tables, 12 primary

Jan 1, 1928

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some&apos; grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,&apos; who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944