Search Documents

By R. M. Brick, M. A. Williamson

CERTAIN features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difference in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and 90°, as compared with drawn brasses, at 45°, for all compositions between 90-10 and 70-30.4 Data on individual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 EXPERITMENTAL METHODS The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per. cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 brass. Sections ¼ in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled-i.e., turned through 90 for each pass-and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained:

Jan 1, 1941

By Charles T. Van Winkle

Until the advent of the porphyry coppers and the introduction of flotation which soon followed, crushing and grinding for many years proceeded along somewhat stereotyped lines, without important alteration in type of machinery. For the finer crushing and grinding, stamps, rolls, and various patterns of Huntington and Chilean mills were in general use. Ball-mills were in use abroad, but owing to their small capacity and the high cost of screens and steel, they never obtained much footing in the United States. Tube-mills were first introduced into the crushing departments of cyanide plants when it was found that for crushing finer than 30-mesh other types of crushing machinery were not efficient. In order to crush with one pass, these mills were made 18 to 22 ft. (5.5 to 6.7 m.) in length. Pebbles were used as a grinding medium and the mills were lined with either silex blocks or fragments of quartz or flint pebbles set in cement. While the cylindrical tube pebble-mill had been used to some extent in small installations of concentration mills, the first instance of its use on a large scale was at the concentrating plant of the Miami Copper Co., where 8-ft. by 22-in. (2.5-m. by 55.9-cm.) Hardinge mills were tried out against Chileans. The results of these experiments led to the gradual replacement of the Chilean by the Hardinge mill. Robert Franke published an article' describing the work done, comparing the two types of mills. At the same time, according to Franke, a test was run using a 6-ft. (1.8-m.) Hardinge ball-mill as a substitute for rolls for intermediate crushing on 1/2-in. material. According to Franke, this mill was soon discarded, since it was found that to obtain the desired product the mill must be limited in capacity. The Miami Copper Co. made no test with other types of ball- or pebble-mills. Following this example, others installed the conical type; and when the Inspiration Consolidated Copper Co. decided to build a concentrator, it adopted the conical mill. As the requirements for mills would be very large, it purchased manufacturing rights in the State of Arizona from the

Jan 1, 1918

By R. G. Davies

Above 500°C, where dislocation climb is rate controlling, it is observed that the activation energy for creep is independent of the apblied stress, although it varies from 62 kcal per mol at 15 pct A1 to 73 kcals per mol at 20 pctA1 due to the change in short-range ovdw with composition. Below 500°C, when the nonconservative motion of jogs upon dislocations is thought to be rate controlling, the activation energy is stress dependent. A sudden increase in the creep rate, for which no explanation is availab2e, occurs at the highest stress at all temperatures. CREEP has been the subject of numerous research publications during the past decade with most of the attention focused upon high temperature steady state creep, i.e., above 0.5 TM, where TM is the absolute melting temperature, as it is the most amenable to theory. Many of the proposed theories involve the climb of dislocations out of their slip plane, which allows them to circumvent obstacles or to annihilate dislocations of opposite sign on other slip planes.' For pure metals it is observed that the activation energy for this creep is equal to the activation energy for self diffusion.' The position is much more complicated in alloys as there are many possible microcreep mehanisms, as well as dislocation climb, which could be rate controlling. There has been little systematic investi- gation of alloys, but Weertman (lead and indium base alloys)3 and Lawley, Coll, and Cahn (Fe-A1 alloys)4 suggest a microcreep process as the controlling factor. A Cottrell-Jaswon atmosphere mechanism is proposed for the lead and indium alloys, and a mechanism involving crystallographic order for the Fe-A1 alloys. Lawley et al. showed that the formation of a super-lattice, either of the FeAl or Fe3A1 type. decreased the rate and increased the activation energy for creep. From the measurements of lattice parameters,= resistivity,' magnetic properties,7'8 internal friction: and dilatometry10 the ordered region is thought to commence at -19 at. pct Al. However, a recent investigation by the author indicates a value

Jan 1, 1963

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By Alfred H. Bell

The year 1937 has been outstanding in the history of the Illinois oil industry. During the course of the year the state's daily production has been trebled, increasing from 12,000 bbl. per day at the beginning to 37,000 bbl. per day at the end, and the year's total, 7,426,000 bbl. is 66 per cent above the previous year's production of 4,475,000 bbl. The production in January was 368,000 bbl.; in December it was 1,085,000. Production from the old fields increased slightly. Most of the new production is from fields in the central part of the Illinois Basin, an area that for many years was considered unfavorable to the occurrence of oil and gas. The principal producing horizon of the new fields is the McClosky "sand," an oolitic limestone in the Ste. Genevieve formation of lower Mississippian age. Although development has not yet gone far enough to permit accurate estimates of oil reserves in the new fields, it is believed that they are of the order of 100,000,000 barrels. The following are the oil fields discovered in 1937 listed in order of amount of daily production at the end of the year; Noble (Richland County), Clay City, including Southeast Clay City (Clay and Wayne counties), Patoka (Marion County), New Centralia (Clinton County), Olney (Richland County), Cisne (Wayne County),.Beecher City (Fayette County), and Rinard (Wayne County). One gas field, the Russellville, in Lawrence County, was discovered in 1937. For locations of the new fields see Fig. 1. A generalized geologic column for Illinois, showing producing horizons in the new fields, is given in Fig. 2. The total productive area of the new fields at the end of 1937 was 1712 acres, in which 230 wells were producing. Thisrty-five dry holes were drilled within 1/4 mile of producing wells. At the end of the year there were 19 drilling wells, 28 rigs standing, 18 rigging up and 4 new locations in these fields. In the whole state 447 wells were completed, of which 284 were oil producers and three gas producers. Total initial daily production of

Jan 1, 1938

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By Harold H. Goe, Louis V. Bender

The recovery of arsenic was started at the Washoe Reduction Works (later called the Anaconda Reduction Works) in 1904, when an arsenic plant was constructed adjacent to the lower end of the 60-ft. main flue.' This plant originally consisted of a Brunton roasting furnace for treatment of flue dust and a small reverberatory furnace for treating the crude arsenic produced in the roasting operations, together with the necessary kitchens for condensation of the fumes and grinding and barreling apparatus for preparing the refined white arsenic for market. The Brunton furnace was fired with wood. It was 14 ft. 6 in. in diameter with two outside fireboxes. The hearth revolved upon a central shaft. The charge was fed through a dust-tight hopper on to the center of the hearth and slowly moved to the outer edge of three rows of stationary rabbles fastened in the roof of the furnace. There was a 3-ft. space between the hearth and roof. A crude arsenic was condensed from this furnace. The hot flame from the fireboxes passed directly over the charge, vaporizing the As203 that was carried through brick flues to the condensing chamber. This chamber was 8 ft. high, 16 ft. wide and 240 ft. long, divided into small kitchens by partitions spaced every 7 ft. It was connected with the main flue system to provide draft and to receive any losses from the chamber. The small kitchens were connected by openings in such a way that the fumes took a zigzag course, causing them to come in contact with the cold walls and ceiling and condense the arsenic. There was an opening from the outside into each kitchen, for the removal of the deposited arsenic, which was closed by a wooden door. The refining furnace was a small coke-fired reverberatory having a hearth 10 by 20 ft. in dimensions. It had three hoppers through which the crude charge was introduced, and one firebox placed at one end. The hot gas from the burning coke passed over the charge, volatilizing the arsenic and carrying it to the kitchens.

Jan 1, 1934

By H. J. Maguire

(Presented by invitation at a meeting of the Spokane Local Section, Feb. 17, 1912.) THOSE familiar with mill-practice understand the work required of an average bucket-elevator, but I wish to call special attention to the wear on the buckets. I have been studying in what manner the life and service of the bucket might be improved, and I feel that an adjustable lip, attachable to each bucket without the aid of rivets, will be of material advantage. For illustration, consider the feed-elevator of a typical mill in the Cur d'Alène district. The ore is carried by water in a launder from the feed-rolls and dumped in the "boot" of the elevator, directly in front of the ascending bucket. Middlings from the return-rolls are similarly handled. Under this condition the bucket not only carries the ore, but also picks it up, and this latter requirement determines the life and service of the bucket. It might be said that it would be better practice to convey the feed to the elevator and dump it directly into the bucket, but at one mill at which this plan was tried the results were disappointing and the rubber belt was badly worn. The wear of the bucket is confined to the lip and the corners which have to pick up the material. When the lip on a corner of a 7- by 12-in. malleable cast-iron bucket is worn down about 3 in., the bucket is of no further value as a carrier and has to be replaced. The worn bucket, containing about three¬quarters by weight of the metal of the original bucket, has a scrap value of about 10 per cent. of that of a new bucket. To the cost of the bucket, however, should be added the time-cost of replacing the old bucket by a new one. This time-cost is considerable when the loss per hour, to cease operating the mill, is about $200. It is out of the question to put lips on a bucket unless the latter was originally fitted with this device. For if it is attempted to fit lips upon buckets not originally provided with

Sep 1, 1912

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By H. R., Collins

THE purpose of pulverizing coal before burning it is to make available every heat unit it contains. Machinery has been developed which will pulverize coal in one operation, delivering it to bins in front of the furnaces at an expenditure of about 17 hp.-hr. per ton, in a medium-sized plant. The cost of the operation depends upon the amount of moisture that must be expelled before pulverizing, the cost of labor, and the cost of coal delivered at the plant. At a small plant, requiring a pulverizer with a capacity of only ½ ton per hour, the cost per ton pulverized will naturally be greater than at a plant requiring the largest pulverizer, with a capacity of 7 tons per hour. The first step is to reduce large lumps to a size suitable for drying uniformly, before passing to the pulverizing mills; this is done in rolls, at a single pass. The second -step is the elimination of moisture, in order to facilitate pulverizing to great fineness, while also increasing the heating effect and the temperature attainable when the coal is burned. There are other mechanical advantages in the handling of, dried coal. Driers are now manufactured which are able to eliminate moisture without distilling any of the volatile combustible matter in the coal; they are fired by hand or with pulverized fuel. The heat first surrounds the shell of the drier, being confined within a chamber where complete combustion takes place; the heated gases are then led through a duct to the discharge end of the drier and enter the inside of the shell at a temperature not exceeding 300° F. This temperature is maintained by the operator and is indicated by a pyrometer. Volatile combustible matter is not likely to be distilled until the temperature rises above 400° F. On discharging from the drier, the coal is usually passed over a magnetic separator in order to prevent pieces of iron from going to the pulverizer. Two types are used: a magnetic pulley which automatically discharges its collection of iron, and a lifting type, from which the iron is removed by hand when convenient.

Jan 4, 1918

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By J. F. McLaughlin

The installation of the Chance flotation system for the preparation of anthracite demonstrated the need for some means by which the specific gravity of the fluid mass in the separating cone could be determined with a fair degree of accuracy. The means used (with the original cones) was a set of wooden balls attached to ropes or chains, each with a different specific gravity. In the Northern Anthracite field, where the cones are generally operated with the specific gravity at 1.65, these gravity balls are provided with a range of 1.6, 1.65, 1.7 and 1.75. The operator of the cone from time to time would place one or more of these balls in the cone and estimate its specific gravity by the action of the balls. The margin of error with this system was very great, because there was the possibility that the test ball might be held in suspension and carried around by material floating beneath the surface of the cone in what is known as "island " formation—a formation resulting from a low sand line in the separating cone. The inaccuracy of this system of determination of specific gravity was indicated also by periodic tests of the final refuse bank, which showed excessive losses of coal to the refuse. Further evidence of the unsatisfactory operation of the cone was the uneven appearance of the market product, which caused spasmodic condemnation. Maintenance of Even Preparation With the critical market condition of today, it is essential that the preparation units operate consistently to maintain an even preparation. If a plant wishes to maintain a 1.65 specific gravity preparation, which means that all material of a specific gravity greater than 1.65 is classed as "reject," if the specific gravity of the fluid mass runs to 1.70, the market product will not be satisfactory; or if the specific gravity of the fluid mass is 1.60, the market product will be entirely satisfactory but the losses at the slate ends will be excessive. The desired specific gravity of the fluid mass in the Chance cone is maintained by agitating the sand within the separating cone by means

Jan 1, 1931

By C. E. Wood

THE Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1939

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

By D. J. Salley, M. Burke, G. L. Simard

A PREVIOUS paper1 described experiments on the interaction of dithiophosphate with galena and suggested that the process had characteristics of both chemisorption and surface chemical reaction. In order to add to this knowledge, a study has been made of the competition of a second ion with the dithiophosphate for a galena surface. Use again was made of radiotracer methods. Since radiophosphate was readily available, it was chosen as the competing ion. It is a feature of the tracer method that, in spite of similarity in the chemical behavior of the ions, the measurement of one ion in the presence of another can be made as simply as if only one ion species were present. In order to study the competition effectively, it naturally was necessary to examine the interaction of phosphate with galena alone as well as in the presence of dithiophosphate; consequently, this report consists of two parts. The first is devoted to a study of the rates, the isotherms, the desorption, and the exchange in the phosphate-galena system in the same manner as was done for the dithio-phosphate-galena system. The second portion is concerned with the studies on the competition. Flotation experiments on the three-component sys- tem are also outlined and the relationships involved are discussed briefly. The experimental method was that of the previous paper. The preparation of the galena, the radioactive and the nonradioactive dithiophosphate, and the procedures for radioactive counting, for sorp-tion, and for flotation measurements were identical to those previously employed. The radiophosphate* was used in the form of disodium phosphate solution. In the competition experiments the effect of the phosphate ion in depressing dithiophosphate uptake was followed by holding the initial concentration of nonradioactive phosphate constant while varying the initial concentration of the radioactive dithiophosphate. Counterfashion, the depression of phosphate by dithiophosphate was obtained by keeping the initial nonradioactive dithiophosphate ion concentration constant and altering the initial concentration of the radioactive phosphate ion. All solutions were buffered at a pH of 7.8 a0.1 by 20x10-' mol per cc of sodium carbonate. Measurements with radiocarbonate indicated that little or no carbonate could be sorbed in the presence of

Jan 1, 1952

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940