Search Documents

By W. N. Lacey, B. H. Sage

THE results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of gravel screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. INTRODUCTION Gravel screens have been placed in water and oil wells for a number of years1,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. INFLUENCE OF GRAVEL SCREENS UPON PRODUCTIVITY The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the. average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized- spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1941

Jan 1, 1894

By W. B. Wise, H. D. Attra, W. M. Black

The purpose of this paper is to illustrate a comparatively new approach for solving a problem that has plagued oil producers for many years—how to make the most money with available field production capacity. In a very basic operation such as a top-allowable one-well field, a computer and staff of engineers are not required to determine that the best operation is to produce that well at its maximum for as long a time as it will produce. However, as the problem becomes more complex and the number of wells and number of reservoirs increase, it probably will be a wise choice to devote some engineering thought and calculation time to determine the best way to operate that field on both an ultimate and day-to-day basis. Continued developments in the field broadly referred to as "operations research" have led to a number of useful engineering analyses for optimizing field operational problems. One of these techniques, termed linear programing, is parlicularly interesting because of its potential applications to the study of complex oilfield operating problems. Linear programing is concerned with the problem of planning a complex set of interde~endenl activities in the best possible (optimal) fashion. A field application of linear programing is being used to maximize daily income from a multi-reservoir producing operation. The initial results of this study indicate that the linear programing technique (I) can be applied effectively to field problems, (2) can be used to detect unsuspected avenues for improving operations and (3) can effect a significantly improved means of controlling field operations through the use of the highspeed computer. INTRODUCTION The usual approach for studying complex field operational problems has been to look in detail at several basic plans suggested by judgement and experience and, then, to choose the best plan from those investigated. This approach is entirely satisfactory provided: (1) that judgment and experience alone will reliably pick the best or near the best program as one of the plans to be investigated; and (2), and most important, that the factors which control field production will not change. This paper deals with the large group of field operations which are at least one-step removed from a satisfactory solution using the conventional method of analysis. Problems such as pipeline- and gathering-system design, transportation studies, large field development projects and multi-reservoir producing operations fall in this latter category. To find the best program for handling these problems when the best program is not obvious, a complete optimization study is required, and high-speed computers are required to continually update the program once it is selected. Operations of this type have an extremely large number of possible solutions. However, only one will result in maximum economic return and, more important, this one program must be re-evaluated and adjusted constantly to accomodate such changing field factors as the number of producing days, the price of crude, the discovery of new reserves, declining reservoir pressure with subsequent decline in production and a host of other factors which characterize specific operations. One of the most widely used, direct methods of optimization is a numerical procedure termed "linear programing", which is designed to investigate systematically each of the possible solutions involved in a given problem, determining rapidly and uniquely the optimum answer. As implied by the name, linear programing requires that all field variables be either defined or expressed in a series of interdependent linear equalities or inequalities. These relationships are solved simultaneously, using a form of matrix solutions to determine the optimum values for each producing variable that will maximize net profits. The solution techniques used in a recent field case study is termed the "simplex method" and is discussed in full detail in Ref. 1.

By William L. Langdon

PRELIMINARY COMMENTS Recent years have been difficult for the mining industry, as reported in the most recently published Minerals Yearbook (Volume III), the estimated value of world crude mineral production has been generally declining since an historical peak in 1979 (16).* The costs of mineral extraction have, however, been rising rapidly. Individual project costs are, in general, exceeding the growth rate of mining companies, while operating and technical risks continue to increase (16). Risks resulting from currency flotation and political actions in the host country are also on the increase. Labor difficulties (such as those experienced by Phelps Dodge) and the Reagan Administration's recent rejection of a proposal by the International Trade Commission for higher tariffs and/or quotas on copper imports have also contributed to the mining industry's difficulties. The net result of these factors has been financial difficulties for mining companies with respect to paying for their current financial obligations as well as trouble finding new financing. It may be that one of the main factors in determining the future of the mining industry will be centered upon capital structure, i.e. how its assets are financed. Historical Perspective on Capital Structure In The Mining Industry As discussed by Isreal Borenstein in (4) and Thomas Navin in (7), mining firms typically have used a financial model based upon high financial leverage, i.e. large amounts of debt relative to equity. This has been especially true for American firms developing orebodies discovered overseas. Problems sometimes occurred for those who were forced to commit themselves to completion guarantees in order to obtain bank loans. Mines under these circumstances must be brought into operation regardless of market conditions. Politicians in overseas countries also may use the high profits required by these high risk ventures to argue for nationalization of mines. Coupled with the frequent use of high leverage, mining companies traditionally have paid out a higher percentage of earnings in the form of dividends than manufacturing firms. This is significant, in that such funds paid out in dividends are not available for other uses. Hence, a greater reliance upon debt and/or additional stock issues than would ordinarily be the case for manufacturing firms. Thomas Navin has stated in (7), that the theory behind the high dividend payout was that, "most mining investors thought of themselves as investing in a wasting asset, one that would gradually deplete over time until it ultimately became valueless." Investors, therefore, required a receipt, in the form of dividends, of a percentage of current earnings and a return on original capital. This view of reality, apparently, has not changed in some quarters, even though modern mine management ordinarily replaces depleted mines with new ones. It may be that this practice of high dividend payout coupled with relatively high financial leverage should be reexamined. Current capital structure theory could prove interesting and useful for those concerned with current conditions. Capital structure patterns and related practices in this industry are not, in many cases, congruent with those thought by some to be theoretically optimal. Prelude to Capital Structure Discussion With a few notable exceptions (such as the Guggenheims and Anaconda's chief operating,. officer in 1971) mining companies' chief executives and boards of directors have not been persons with financial backgrounds. This, one could conjecture, might have accounted for the relatively nonsophisticated nature of capital structures of mining companies. In order to appreciate the possibilities with respect to alternative influence on a firm's performance, one must be acquainted with the basics of financial theory. This paper is an attempt to familiarize the reader with (1) capital structure in general, (2) the usual components of this structure, (3) the general theory behind the use of financial leverage, and

Jan 1, 1985

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By R. E. Reed-Hill

Recently Levine applied the Conrad-Wiedersich17 equation where H is the activation enthalpy, v the activation volume, T* the effective shear flow stress, T the absolute temperature, and ? the strain rate, to an analysis of titanium single-crystal data. The activation energy as a function of testing temperaturs obtained from specimens oriented for single (1010) prismatic slip is shown in Fig. 12. This diagram indicates a different linear dependence of H on T in the temperature interval from 220° to 300°K than from 0° to 220°K. Levine interpreted the break in this curve as indicating a change in the thermally activated mechanism controlling the flow stress. The purpose of this communication is to point out that the data in Fig. 1 is not consistent with the concept of a flow stress controlled by a simple thermally activated mechanism between 220° and 300°K. The Conrad-Wiedersich relation assumed that the strain rate can be expressed by:

Jan 1, 1968

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.' In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature microhardness of as-grown and annealed MoaC single crystals was measured on the (0001), {2110), and1012) planes using Knoop and Vickevs indenters at loads ranging front 25 to 1000 g. The orientatimz dependence of hardness with respect to crystal axes was also studied. The average random hardness of as-grown crystals was determined to be 1520 kg per sq nm. Annealing to 2000°C decreased. the average hardness by 150 units. An increase in hardness after annealing at 2200 ;C was noted. Optical and electron microscopy revealed slip and twin traces on all planes studied, as produced by mi-cvohavdness indentations. Basal (0001)(2i10) slip was determined to be the primary slip system and was substantiated by electron transmission microscopy. A secondary {1010)(2110) slip was produced by mi-crohardness indentations. The lattev also produced twinning- of the {10i2)[0001] type, as proven by electron diffraction. Electrical resistivity and elastic-modulus anisotropy were found and correlated with hardness anisotropy and Mo2C crystal structure. Elastic-modulus values were obtained by microhard-uess and ullrasonic methods. Bonding mechanism of Mo2C is discussed. ROOM-TEMPERATURE microhardness indentations are useful for studying hardness anisotropy, slip, and twinning in brittle materials. Slip has previously been produced in this manner in and WS~~.~ Recently, the authors5 reported slip of the {10i0)(11~0) type produced by high pressure and microhardness indentations on hexagonal TiBz (c/a = 1.066) single and polycrystals. This slip system was also reported by French and ~homas' and Taka-hashi and ~reise~ for hexagonal WC (c/a = 0.976) crystals. These results suggest that prismatic rather than basal slip is favored in hexagonal nonmetallic materials having a c/a ratio considerably less than the ideal (1.633). Buerger precession and cylindrical X-ray rotation patterns were previously' taken on cleaved sections of the Mo2C single crystals studied in this work. Th~y were found to be hexagonal MoaC with a. = 3.0233A, co = 4.7344A, and C/O = 1.5660. The latter ratio is close to that of the beryllium metal (c/a = 1.57), which slips primarily on the (0001) plane: but also slips on the (1010) planes.'0 ~irconium" (c/u = 1.59) and titanium12 (c/o = 1.59) deform mainly by slip on nonbasal planes which contain a close-packed direction. This is due to the fact that for these two metals the initial resolved shear stress for slip on the (10i0) prismatic planes is lower than that on the (0001) plane. The prominence of basal rather than prismatic slip in metals of high c/o ratios is shown by cadmium (c/a = 1.89), zinc (c/a = 1.86), and magnesium (c/a = 1.62) which deform mainly by basal slip. However, in case of the latter, by stressing magnesium crystals in tension or compression parallel to the basal plane, slip on (10i0) planes can also be produced.13 Several hardness values for polycrystalline Mo2C are reported in the literature: Biickle ' and Samsonov'~ give a value of 1800 and 1479 kg per sq mm, respectively, at a 100-g load; and Kieffer and Benesovsk~'~ report a value of 1950 kg per sq mm at a 50-g load. ~ott'~ reports a Vickers hardness value of 2000 kg per sq mm, with the load unspecified. A Rockwell A hardness value of RA = 88 has also been reported.'' In the present work, for comparison with single-crystal Mo2C hardness values, a Khnloo value of 1600 It 150 kg per sq mm was found on 99.6 pct pure and 99 pct dense hot-pressed Mo2C. This work was undertaken partly to explain the considerable differences in hardness values reported for polycrystalline Mo2C. EXPERIMENTAL The Mo2C single crystals investigated were prepared by a Verneuil-type process using an electric arc by the Linde Co. of the Union Carbide Corp.lg The largest specimens grown were boules 7 mm in diam by 40 mm in length. The crystals had an average density of 9.04 g per cu cm, with a Mo + C content of 99.8 wt pct. The major impurities were: 100 ppm each Na, Zr, and Ca; 85 ppm 0, 55 ppm Fe, and 10 ppm each Cr and Ta. The crystals were found to be carbon-poor, the average carbon content being 5.73 wt pct (stoichiometric value is 5.89 pct). The molybdenum content was found to be 94.08 pct, which is nearly stoichiometric. Electron-microprobe traverses of selected specimens were done with a Phillips-AMR microanalyzer. Thin-film and carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to optical and electron-optical studies, specimens were mounted in Lucite and polished on a vibratory polisher using diamond-paste grades ranging from 9-1 p and Linde A powder for up to 48 hr. Dilute nitric acid was used for thin-section polishing and chemical etching for 1-15 min. Electrical-resistivity measurements at room temperature were taken with a Rubicon bridge, using gold contacts. For hardness measurements, a Tukon Microhardness Tester Type FB with Knoop and Vickers indenters was used. Measurements were taken at loads ranging from 25 to 1000 g; however, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Indentations of cracking classes 1 and 2 only were considered for hardness determinations.20)21 (There are six cracking classes, ranging from "class 1" for a perfect inden-

Jan 1, 1967

By R. W. Raymond

GEHEIMER BERGRATH Prof. Dr. HIERONYMUS THEODOR RICHTER, ex-Director of the Freiberg Mining Academy and Honorary Member of this Institute (to give him the full title, which nobody ever thought of using in his genial and unceremonious presence, and the whole of which I have omitted at the head of this notice, as adding nothing to the virtue and value of the man I knew), died on Sunday, September 25,1898. He was born in 1825 at Dresden, and in 1843, after some practical training in pharmacy, entered the Freiberg Mining Academy, where he devoted himself chiefly to metallurgy and metallurgical chemistry, under the guidance of the celebrated Plattner, whose masterly instruction in those arts, and also, especially, in assaying and the use of the blow-pipe, has been classic authority to the present day. In 1853, Richter was ap-

Jan 1, 1899

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues' have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.' Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer's value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,' analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Schürmann series of replacability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist's viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells2 discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions.

Jan 1, 1929

By W. P. Blake

THIS furnace is designed especially for the oxidation of sulphur or arsenic in pyritic ores, but may be used for all oxidizing or desulphurizing operations, and for calcining, roasting and chloridizing ores, or for drying ores in large quantities preparatory to treatment by magnetic separators or otherwise. It is of the tabular, revolving type, with automatic feed and delivery, and is a modification of the Cornish calcining furnace, designed by Brunton, from which it differs, however, not only in construction, but in two or more radical features, for which novelty is claimed and patents have been applied for. The principal of these novelties are: 1. A series of concentric terraced floors, one above another. 2. The introduction of superheated air upon the charge without contact with the fuel. In the furnace which I have had in operation for more than a

Jan 1, 1893

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.'-' The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.', 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards' law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525', 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By J. L. Huitt, B. B. McGlothlin, D. K. Lowe

Published correlations for the principal aspects of hydraulic fracturing were combined into a digital computer program to facilitate the study of interrelated variables. The computer program includes individual relationships for fracture width during pumping, fracture area generated, propping agent embedment, flow capacities of propped fractures and transport of propping agents in horizontal fractures. The effects of more than 20 treatment and formation parameters on the predicted results of hydraulic fracturing treatments were studied. The effects of these parameters were determined for (I) fracture width during injection, (2) fracture width after the overburden comes to rest on the propping agents, assumed not to be crushed, (3) generated and propped fracture area, (4) location and concentration of propping agents in the fracture when injection ceases, (5) flow capacities of the various propped sections of the fracture and (6) expected increase in the well productivity. The effects of propping agent, formation and fracturing fluid parameters on well productivity are discussed. The parameters that were found to have the most pronounced effects on hydraulic fracturing treat~nents are injection rate, treatment volume, fracturing fluid coefficient, size and amount of propping agent, spearhead volume, well drainage radius and formation capacity. INTRODUCTION Many correlations have been published for predicting effects of various parameters that are considered in the design of hydraulic fracturing treatments. The Carter equation' can be used to predict generated fracture radius as a function of fracture width, fracturing fluid leakoff and other parameters. Fracture width can be determined by use of the Perkins and Kern correlation' in which the fracture width is related to the fracture radius, fluid injection rate and certain formation and fracturing fluid parameters. Wahl and Lowe et aL4 have reported methods of predicting the location of propping agents in fractures when pumping ceases. The former study is applicable to the case where the ratio of propping agent diameter to fracture width is less than 0.1. The latter is applicable when this ratio is greater than 0.1. These studies showed that the propping agent placement in horizontal-radial fractures depends principally on how the individual particles are transported in the fracture by the carrying fluid. Particle transport in fractures is determined by local fluid velocity in the fracture, fluid and particle properties, and the size of the particle relative to the fracture width. The distribution of propping agents, effective overburden pressure and formation rock strength control the propped fracture width6 by controlling the extent to which the propping agent particles embed into the fracture faces. From the distribution of propping agents and the propped fracture width, fracture flow capacities can be calculated or the various regions of the fracture. The flow capacities and the radial extent of these regions can be combined with reservoir information to predict the productivity increases for fractured wells. In all these studies, the effects of certain treatment and/ or reservoir parameters on one facet of fracturing can be predicted only if other facets which the parameters affect are fixed. For instance, fracture width and radius are interrelated; that is, to calculate the value of one, the value of the other must be known. Also, some parameters influence more than one aspect of fracturing. For example, prop-pant transport is a function of both fracture width and fluid viscosity. but fracture width is itself a function of fluid viscosity. Since these calculations are complex and the parameters interrelated, it is not possible to write an equation with which the over-all effects of treatment parameters can be solved explicitly. For these reasons, the correlations for determining the effects of the parameters which are most significant in hydraulic fracturing treatments have been incorporated into a digital computer program. COMPUTER PROGRAM The program, which was written for an IBM 7094 computer, can be used to predict results of most of the combinations and values for the treatment parameters that are ordinarily considered for fracturing treatments. A spearhead of fracturing fluid and a propping agent-carrying fluid with different fluid properties can be taken into account. Also, the total volumes and relative amounts of the spearhead and carrying fluids can be varied. Two different propping agents (as used in tail-in operations) and a wide range of formation properties and injection rates are considered. The computer program (Fig. 12) consists of several sets of calculations. First, the final flooded fracture radius and average fracture width at the cessation of pumping are calculated. This is done by simultaneous solution of the Perkins and Kern fracture width equation and the Carter equation for flooded fracture radius (equations used in the computer program appear in the Appendix). The next step is to determine local fluid velocity in the fracture as a function of time and radius. Since it is not possible to write this function in closed form expression, a table of velocity values is generated by the program and stored for subsequent use. The time span from the beginning of

By A. J. W. Schwandt

Magmont is a venture jointly owned by Cominco American Incorporated of Spokane, Washington and Dresser Minerals, Division of Dresser Industries, Houston, Texas. Cominco American assumed direction of the operation in 1961 and completed exploration, preproduction planning and development, and is now the operating partner managing the operations. The plant has a rated capacity of 4200 tpd and produces in excess of 60,000 tons of lead per year. [ ]

Jan 1, 1970

By AIME AIME

A REGULAR meeting of the Executive Board 'of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee' on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee 'on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882