Search Documents

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952

By Leonard Austin

WHAT Colonel Dwight says regarding the treat-ment of oxidized ores1 holds true also of the silver-lead smelting operations in Utah. The ore sought for was such as would, with appropriate fluxes, yield slag, and "lead bullion," as the lead reduced from the ore and carrying its gold and silver, was called. No matte, and probably little or no speiss, was yielded, and hence there was nothing to roast, either of ore or matte. But, by 1880, when I first took hold in smelting, there was quite a production of matte at the works of the Ger-mania Smelting and Refining Co., Utah, because, by that time, ores containing some pyrite and galena were being smelted. This was due, as at the Grant Works, Denver, to the more attractive price paid for the treatment of such ores. The matte, containing about 5 per cent. copper, was accordingly heap-roasted and returned to the blast furnace for the recovery of its contained metals. By this time there had been built a long-bedded, hand-rabbled reverber-atory roaster with a hearth of about 40 by 10 ft. in size, and in this matte and ore, crushed at the sampling mill, was treated. When, in 1892, I took control of this works, called& now the Germania Lead Works, three other roasters had been added, but the prac-tice of heap-roasting continued. This had the merit of needing no equipment, and of doing good work, because the pieces that were imperfectly roasted went back upon the next roast heap. At this time, when some suitable lump ore was obtainable, I roasted in heaps, in a satisfactory way. By 1892, the Bruckner cylinder roaster had been installed, which, compared with the reverberatory roaster, reduced labor. As such a cylinder revolves, a talus of ore is formed within it and at the same time fresh surfaces are exposed to the air, but the trouble was that the air did not reach to the bottom of the cylinder. This we corrected by placing a steam jet at the fire-box end, to project the air down-ward upon this stagnant ore, thus increasing the speed and completeness of roasting without at the same time increasing dust formation. The firing, if skilfully done, gave a somewhat sintered product, but with certain ores a slight access of heat over the normal would cause accretions to form within the cylinder near the fire end. These could be cut off by running back the fire box and barring off the crusts. It was in 1895 that the Bruckner cylinders at the Arkansas Valley plant, Leadville, were giving unsatis-factory service and I was called in to investigate. The steam jet was put in use as at the Germania Lead Works, but we found that, due to the altitude (10,500 ft.), combustion was feebler than at sea level or even at 4000 to 5000 ft. Later it appears, as Colonel Dwight states, that R. D. Rhodes and Mots sought to increase the air supply by admission through perforated tiles, but the trouble was due to the air itself.

Jan 8, 1922

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By C. G. Dunn, F. W. Daniels, M. J. Bolton

Recent observations on grain boundary movements in sihcon iron have indicated the possibility of studying grain growth phenomena in two-grain specimens in which several variables affecting growth are readily controlled. These variables are (1) the energy per unit area (?) in the grain boundary, (2) the orientation relationship of the two grains, and (3) the radius of curvature (7) of the moving boundary. Ideally, one grain A should be a narrow rectangular parallelepiped adjacent to a second grain ß as shown two dimensionally in Fig 1. Such a two-grain group becomes unstable when one end of grain A is shaped according to the dotted line. Since the width w of grain A remains constant during growth of grain B, T should also remain constant. The other vari- ables mentioned above can be controlled in the preparation of each two-grain specimen.l,2,3 For a parLicular orientation of each grain, is not necessarily fixed; ? may also depend on the orientation of the grain boundary, but this may be controlled to some degree. The energy relationships for the gowth of grain ß may be derived from the more simple arrangement of two grains A' and B' shown schematically in Fig 2. Here B' largely surrounds A'. Assume these grains are oriented with a common plane parallel with the flat

Jan 1, 1950

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By Edward J. Way

+1KLEINFONTEIN GROUP CENTRAL ADMlNISTRATION, BENONI, TRANSVAAL, S. AFRICA. The cost and the speed of sinking a shaft are factors of so great importance in operating a mine, that the data given in Table I., herewith published, will be of interest and value to all engaged in practical mining; and for this reason the data are communicated for permanent and accessible record in our Transactions. The figures 'of cost cover the period from January 1, 1903, to May 31, 1903, during which time the total depth sunk was 858 ft. So far as I know, the cost of sinking per foot (£13,15s., 11.04d.) of a shaft of the dimensions 21 ft. by 6 ft. in hard rock, is the cheapest yet on record; and the speed of 213.5 ft. per month, which was attained during May, 1903, is also the best record for speed in sinking in rock so hard as that of this shaft. During the period from January 1 to May 31, 1903, there were 144 rounds worked, involving 4,032 holes, of a total depth of 28,963 ft. 2.4 in., which is equivalent to an average depth of 7 ft. 2.2 in. per hole bored. These data are of added interest from the fact that the work was done practically by native labor.

Jan 1, 1905

By J. L. Stokes, L. J. Demer

It has recently been shown' that epitaxial films of silicon carbide deposited on silicon single crystals possess desirable properties for semiconductor applications. There is one apparent disadvantage to such a system, however; since epitaxial deposition is a high-temperature process, it can result in plastic deformation of the silicon substrate. The accompanying Berg-Barrett X-ray diffraction photographs reveal plastic deformation in two silicon semiconductor crystals which occurred when the crystals were coated with an epitaxial layer of silicon carbide at 1150°C. Due to differences in thermal expansion between the silicon substrate and the epitaxial silicon carbide, the silicon was subjected to stresses while still in the plastic temperature range. Both crystals shown were 0.7 in. in diam and 0.0055 in. thick. The crystals were sliced from a larger crystal so that their polar axes were parallel to the [ill] direction. After cutting, the crystals were polished with diamond paste, and etched in HC1 vapor to remove surface damage re- sulting from the cutting and polishing operations. This provided clean, damage-free surfaces on which to deposit the silicon carbide. Figs. l(a) and l(b) are reflection and transmission photographs, respectively, of the same crystal. A smaller portion of the crystal is shown in the transmission geometry, because a vertical slit was

Jan 1, 1965

By John M. Cigan

Samples of copper-lead concentrates from the mine of Cia Minerals Santander, Inc., a Peruvian subsidiary of the St. Joseph Lead Co. were recently subjected to special analysis. This concentrate was known to contain bismuth which, under some circumstances, might have incurred a smelter penalty. In this case, customers for the concentrate accepted it and requested a higher concentration of bismuth. Although chemical analysis would disclose the presence of the metal, it was not possible with equipment available at the mill in Peru to determine the mode of occurrence in the fine grained ores.

Jan 11, 1964

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943

By Joseph E. Pogue

NEW economic forces are at work in the petroleum industry.. In order to visualize these forces and clearly see their bearing on the producer, refiner and marketer, it is necessary to see in perspective the economic evolution of the business. For several decades prior to 1913 the outstanding feature of the petroleum industry was a trend toward integration, culminating in a huge combine, the Standard Oil Co. An important aspect of this integrative trend, however, was its concentration on the combination aid control of refining and marketing, leaving crude oil production, for the most part, to the exigencies. of small-unit competition. It is a noteworthy coincidence that during this era the law of oil and gas was formulated and applied, whereby these substances had to be reduced to possession to establish ownership; and the forces of competition in crude oil production were thereby intensified. It was to the interest of an industry, safeguarded in its control of manufacturing and markets, to have supply stimulated by legal convention as well as by individual initiative in order that the growing demand could be met without interruption. And so over-production of crude oil during this era was no handicap, but rather an aid, to the progress of the industry.

Jan 1, 1929

By AIME AIME

A MODERN copper reduction works has both a genera1 chemical laboratory for control work and a research laboratory for the study of improvement of present processes and better working-up of by-products. The division of work in the general laboratory would naturally differ in different plants. The following statement to the writer from a chemist in one of the works will give a good idea of the type. of work in the general laboratory :

Jan 1, 1929

By Sherwin F. Kelly

LITERALLY from the four corners of the earth, from Jerusalem and China, from Mysore and Uganda, as well as from geophysicists in the United States, came contributions from workers in magnetic and electrical geo-physical methods, most of them unfortunately unable to be present themselves. The most lively discussion centered on the phenomena of natural potentials in the earth, dealt with in M. B. R. Rao's paper from Mysore, and in Parke Dickey's contribution, which he presented in person. In the oil fields, the weak potentials observed in sedimentary strata traversed by bore holes have traditionally been ascribed to phenomena of electro-filtration and electro-capillarity. Research tending to refute this theory was presented by Dickey, who reported the existence of natural potentials in core samples, and between strata exposed in underground workings. This precipitated a lively discussion as to the possible role of electro-filtration, selective adsorption of ions by mineral particles, and electrolytic potentials, in the production of this phenomenon.

Jan 1, 1943

By William G. Christy

EFFORTS at smoke abatement date back to the year 1273 in England when a law was passed prohibiting the use of "sea cole." The law was not enforced, so King Edward I, 33 years later, appointed a commission "to enquire of all such who burnt sea cole in the city or parts adjoining, and to punish them for first offense with great fines and ransomes, and for the second offense to demolish their furnaces." Many other commissions have since been named to investigate the smoke problem in England, but it still persists in many British cities. In the United States the movement to abate the smoke nuisance started in certain Middle Western cities, and has made considerable progress. Until recently, the coal-producing industry co-operated little in smoke¬abatement programs, taking the attitude that smoke elimination is the dealer's or user's responsibility; and the dealers, in turn placed the responsibility entirely on the user.

Jan 1, 1942

By Nath S. Parate

Emphasis on publications related to coal mining subsidence and damages is appropriate at present in view of the energy crisis and increased coal production and public alertness. I have worked in Harrisburg with the state government Public Utilities Commission on energy-fuel matters and issues (Parate, 1978-80). I have participated in the communication on subsidence/ damage reviews and status with the Bureau of Mines Liasion Office (Kebblish, 1978-79). I have done research (Parate, 1965) and published papers (Parate, 1972; Parate, 1967) in Britain on coal mining subsidence and damages around Sheffield-Nottinghamshire coal fields. I have a few comments on the recent paper titled, "Pennsylvania Subsidence Control Guidelines," by C.J. Bise. 1) What is the basis of the empirical formula or guideline, LD _ (0.27 x D) ± 4.6, defining the support area? 2) The particular structure may not be damaged due to vertical uniform displacement caused by mining beneath unless the displacement is differential (King, 1964). 3) The author mentions the limited subsidence research in the US, and quite rightly so. But he fails to quote any work reference by continental investigators except the British or review work by the US. What are the reasons? 4) The author has not mentioned the importance and role of angle of draw for Pennsylvania, Kentucky, or Illinois coal fields. Is there any current research investigation on the relationship between subsidence research investigation, damage, and transference of strains to structures? There have been a number of newspaper reports on subsidence damage in Wilkesbarre and other areas in Pennsylvania. Is the author aware of such instances and traditional attitudes to such issues? Many times government agencies--due to lack of funds, technical expertise, and public policies--are unable or do not find it interesting to keep updates on these issues, as per the author's knowledge and experience with state governments. 5) What is the net effect and role of the D.E.R. Insurance Office on the monitoring, reducing, or controlling subsidence damage, particularly in Pennsylvania?

Jan 1, 1983

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described' as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918