Search Documents

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By Walter E. Mingramm

The construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquefied air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the difficulty and cost of keeping on hand a large quantity of liquefied air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found

Jan 1, 1909

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant's Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck's Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson's Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942

By T. S. Lundy, J. Askill

J. Askill and T. S. Lundy (Oak Ridge National Laboratory)—Moore has proposed a simple correlation between the activation energy for solute diffusion in fee metals and the atomic volume of the diffusing species using both tracer and chemical-diffusion data. The first point we wish to make is that it is wrong to attempt such correlations without separating the two types of data. Activation energies obtained using tracer techniques cannot, in general, be directly compared with those obtained from chemical-diffusion experiments. A knowledge of the variations of chemical potentials with composition is necessary and chemical-diffusion data must be corrected for such variations, even for dilute alloys, before a comparison is possible. Secondly, for nickel, iron, aluminum, and lead, Moore neglected a number of recently published works, e.g., Al26 and Mn54 in aluminum,46 cr51 in nickel,47 and Fe55 in iron.48 These and others should have been used. If one considers only the tracer diffusion data, there is left no simple correlation of the type proposed by Moore. For example, in the case of solute diffusion in aluminum the only reliable tracer data listed by Moore are for zinc and aluminum. The nickel, cobalt, and iron data of Agarwala49 are representative of near-surface diffusion-not bulk diffusion. In conclusion we suggest that for tracer diffusion data in these fee metals there is no justification for proposing any simple correlation of activation energy with atomic volume using the limited data that are presently available. R. H. Moore (author's reply)—The writer has proposed a simple correlation which is useful in estimating the internal consistency of diffusion data. The accuracy of the correlation is, of course, a function of the number of data available. Lundy and Askill take issue with the writer's decision to include data for the systems: nickel, iron, aluminum, and lead, taking the view that the data are insufficient to establish the correlation. The writer agrees that the data are insufficient and has cau- tioned the reader that the correlation is tentative in these instances. Inclusion of these systems is justified by the interesting trends the correlation reveals. For example, the distinction between interstitial and substitutional diffusion may be clearly established, Figs. 4 and 6, and the behavior of transition elements and nontransition elements is indicated to parallel the behavior illustrated by the silver and copper systems. Lundy and Askill have singled out the aluminum system for special criticism. The writer chose to discuss the data for diffusion of iron, nickel, and cobalt in aluminum in the terms used by the original authors9 and has included the comments of Balluffi.l0 The writer did not intend the reader to conclude that data for these elements should correlate with data for the nontransition elements as Lundy and Askill have evidently assumed. Iron, nickel, and cobalt form intermetallic compounds with aluminum, so the activity coefficients of these elements may be expected to deviate markedly from unity. This may account for the low frequency factors observed by Hirano.9 The nontransition elements, on the other hand, yield relatively simple phase diagrams with no evidence for intermetallic compound formation as in the case of iron, nickel, and cobalt. In dilute solution, Henry's law should be closely obeyed, the activity coefficients should not deviate markedly from unity, and the effect on the activation energy should not be large. The accuracy of the correlation applied to these systems will improve as the data is extended. It does not seem unreasonable to conclude that its extension should be encouraged.

Jan 1, 1965

By WILLIAM J. LINNEY

MAGNETITE ore from Lyon Mountain, so- called "Low Phos Chateaugay," has long been known to the iron and steel industry for its almost complete absence of impurities. These magnetites occur along the northern foothills of the Adirondacks in several parallel and folded stringers which are continuous for several miles, striking generally northeast-southwest and dipping usually over 45° to the northwest, or roughly toward the St. Lawrence River. Ore of minable thickness is found in shoots of various sizes as to length and breadth, but of undetermined and possible great depth.

Jan 1, 1943

By Howard E. McKinney

A high-pressure wellhead lubricator has been developed to facilitate telemetering electrical measurements from subsurface reservoirs to the surface with the well under normal flowing conditions. The field unit in use at the present time employs a 5/16-in diameter, single-conductor armored cable and is to be used in wells with surface pressures up to 5,000 psi. It has a pressure sealing element that maintains a continuous and absolute seal around the cable as it enters or leaves the tubing at speeds up to 175 ft per minute. A cable injecting device is used which obviates sinker bars or weight sections on the instrument. INTRODUCTION The development of instruments for securing physical measurements in pressure wells has been confined in the past to those instrument which would operate on a wire line and record the necessary measurements in the downhole instrument itself, or those which would operate on an electric cable in a well with the surface pressure killed by the use of weighted fluids or by the use of tubing plugs. In one case the accuracy of the measurements is questionable, and in the other the range of application is very limited. Considerable work has been done by other interests to provide effective means to accomplish the necessary telemetering. The U. S. Bureau of Mines developed a wellhead lubricator prior to 1947 which permitted a 5/16-in diameter single-conductor cable to be lowered into a well with a surface pressure of approximately 500 psi. This unit was used successfully in a number of tests in Oklahoma. A company which tests wells has recently offered on a service basis a wellhead lubricator with a 3/16-in diameter cable that reportedly operates up to 2,500 psi surface pressures. Each of the above operates on a staging principle to effect a seal. In both of these units some leakage of well fluid occurs when the cable is moved. SPECIFICATIONS FOR DESIGN In order to provide the maximum flexibility in its use, the following parameters were established for the design of our high-pressure wellhead lubricator: L An absolute well fluid seal up to 5,000 psi surface pressures. 2. Means for raising and lowering the instrument at speeds of at least 100 ft per minute. 3. Provision for the instrument to enter and leave the well without disturbing the well flow or the reservoir conditions. 4. A cable large enough to provide suitable electrical characteristics and suitable mechanical properties. 5. A method of operation that will not damage the well in any way. The present high-pressure wellhead lubricator field unit fulfills the above requirements. DESCRIPTION OF THE UNIT AND ITS OPERATION The cable selected for this use is the standard Amergraph 1H2 as manufactured by the American Steel and Wire Co. This particular cable is normally used by the Halliburton Oil Well Cementing Co. in their conventional well logging operations. Although the cable presents a noncircular cross-section (Fig. l), its diameter is very consistent; lor example, maximum diameter is 0.325 in., minimum diameter 0.314 in. This [actor permits the use of the sealing element, as later described. Early in the development of the high-pressure wellhead lubricator it was apparent that we could not effect a direct gas seal around a moving 1H2 cable. This becomes evident when an examination of the cable cross-section is made. The voids between the strands of the outer armor provide natural channels lor the flow and escape in large quantities of a low-viscosity fluid such as gas. However, it is relatively simple to

Jan 1, 1952

By J. A. Richardson

J. A. RICHARDSON[t]-Mr. Stuckey's account of the geology of the kaolins of North Carolina suggests that they exhibit some features similar to those of the Malay Peninsula. About one half of British Malaya (some 26,000 square miles) is occupied at the surface by igneous rocks, of which granite and its associated derivatives constitute fully 90 pct. The average granite is a biotic variety. It is predominantly potassic but carries, in addition, notable amounts of soda and lime so that albite and albiteoligoclase are generally common constituents of the rock. The minor derivatives from granite "magma" likewise include potassic and sodi-potassic members. Decomposition of the granitic rocks has led to the formation of kaolin in many localities, but, in general, the deposits are rather small and, at present, none is exploited commercially. True primary or residual kaolins (as defined by Stuckey; p. 48 Vol. 173, p. 2 TP 2219) have been developed from feldspar veins, pegmatites and from other granitic differentiates which cut through the larger masses of granite; they are usually small and narrow. Kaolin has been derived from aplite, quartz porphyry, quartz micro-porphyry, felsites and microgranites belonging to a complex known as the Chegar Perah-Pulai intrusion in northwest Pahang and southwest Kelantan. The bulk of the component rocks has been more or less strongly sheared. Kaolin-like end products have been formed from both sheared and nonsheared varieties. Kaolin has been formed also by the complete breakdown of trondjemite flanking the northwestern and western margins of the complex Bukit Ranjut syenite intrusion in northwest Pahang. These trondjemites range in composition from essentially quartz-free albiteplagioclasites to quartz-free microcline rocks; they are, in effect, the syenitic homologues of white sodic and potassic granite-aplites. The granites in Malaya have generally undergone more or less severe surficial weathering leading to the production of a spongy and rather cellular or a soft "mealy" material (sandy clay) down to depths of about 100 ft; in places the granite is strongly decomposed down to 150 ft. There has occurred, therefore, widespread partial kaolinization, but, in general, no extensive deposits of good quality kaolin seem to have been formed by these processes of decay. Frequently, the katamorphic processes of desilicification have advanced beyond the production of kaolin towards the formation of lateritic end products. The more important Malayan kaoiins seem to be confined to the western alluvial plains, particularly in areas either where granite crops out at surface, or where it forms the bedrock of the alluvium. There are numerous excellent examples around Gopeng and elsewhere in the Kinta Valley of Perak. Such kaolins belong to Stuckey's groups of secondary deposits, and, like them, these also may be bedded. Field observations have established the existence of what for want of a better name is referred to by the Malayan Geological Survey as "granite wash." It is believed that granite, undergoing extensive deeply penetrative and probably rather rapid destruction under humid tropical weathering (temperature around 90°F; rainfall about 100 in. per annum; high humidity) "flowed," was moved by "creep" and, in addition, probably slumped in large waterlogged masses of sandy clay from topographic salients onto the adjacent flats. Either during this period of transmigration or later when the sludged granite detritus, after having more or less come to rest, was attacked by flowing water, differential sorting and erosion took place with the result that the resorted debris was moved and later deposited as bedded alluvium. In this way, banded "granite wash" was produced comprising alternating bands of clayey sand (resorted granite sludge) and white

Jan 1, 1947

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By R. C. Allen, Ralph Arnold

The writers have no new system and no new principle of taxation to propose. The general subject of taxation is as old as governments are and as familiar to taxpaying Americans as the general thesis on the inalienable rights of man. We believe, therefore, following the committee of the National Tax Association, that improvement in the general conditions of taxation, including mine taxation, maybe brought about mainly through a better adjustment of known and tried principles and methods of taxing to modern complex forms of property and income, and that not much is to be expected from abandonment of experience for new ways and means, methods and principles, should anything new be discovered, which in our opinion is very doubtful. The committee referred to has constructed the general framework of its Model System of State and Local Taxation1 on familiar forms of taxing, by eliminating some that ' have proved bad, suggesting improvements in others, and adopting the best, leaving plenty of room for the accommodation of the general plan to the varying conditions of taxation in the several states. Unfortunately, the taxation of mines is dismissed by the committee with the statement that the subject has been reassigned for further investigation and report by a special sub-committee, frankly recognizing that the peculiar difficulties of this phase of the subject require special study and investigation. Much may be hoped for from the labor of this sub-committee if the problem is approached from the viewpoint of recommendations already published. In this paper, the writers state their opinion on some of the broader aspects of mine taxation with too little attention to the grounds on which they rest. Contrary to inclination space requirements compel them to resort to summary statements without adequate discussion for a satisfactory presentation of the whole subject. All they can do is to qualify the witnesses and record the testimony. The senior writer was introduced to the practical aspects of the subject of this paper in 1913, when, as State Geologist of Michigan, he was

Jan 1, 1920

By AIME AIME

AT a recent meeting of the Utah Section. A.I.M.E., P. D. Nielson, general plant superintendent of the new Geneva steel plant at Provo, Utah, spoke on "General Operations of the Geneva Plant." Mr. Nielson explained that the plant was located at Provo, Utah, on account of railroad facilities, the proximity of coal, iron, and limestone, and the nearness of water for operating the plant. Water probably was the most important item in making the decision.

Jan 1, 1944

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By John W. Vanderwilt

THE Climax district is in northeastern Lake County, Colorado, on Fremont Pass (elevation 11,320 ft.) where the continental divide runs east-west joining high peaks of the Mosquito Range with the Sawatch Range, prominent ranges of the central Rocky Mountains. The mining towns of Leadville and Kokomo are thirteen miles to the south and seven miles to the northwest, respectively. Good highways lead to Denver (100 miles) by way of Kokomo, Loveland Pass, and Idaho Springs, and to Colorado Springs by way of Leadville. The ore deposit and mine are about one mile east of Fremont Pass and 600 ft. higher on the southwestern flank of Bartlett Mountain, a peak in the Mosquito Range. The molybdenite deposit lies within the Colorado mineral belt extending across the Rocky Mountains from Jamestown and Boulder to Silverton and Telluride. (See Fig. 1.) Fremont Pass is a broad open divide separating the drainage of the Tenmile River (Pacific) from that of the East Fork of the Arkansas River (Atlantic) ; but the mountains to the east and west are extremely rugged; altitudes in the vicinity vary from 11,000 to 14,000 ft. A conspicuous topographic feature within the district is the Tenmile Amphitheater, which lies east of Climax and

Jan 1, 1946

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

J. W. RICHARDS*(South Bethlehem; Pa.).-The brass industry would find it very profitable to subsidize researches on the purely scientific determination of the thermophysical properties of the brasses. The data we need most in connection with the brasses are the vapor tension of the zinc from the brasses at different temperatures, the heat of combination of zinc With copper to form different kinds of brasses, and the latent heat of fusion of these brasses at the melting temperature.

Jan 1, 1919

By A. Tonejc, A. Bonefacic

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26o +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr , Ni , Sb , Mn , P , Sn , and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

By P. R. Smith, R. A. Walters

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915. In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various boiate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 122 m (400 ft) deep, 910 m (3000 ft) long and 305 m (1000 ft wide). The borates in the Boraxo pit consist primarily of three minerals. These are about 50% colemanite (CB6011 5H20), about 40% probertite (NaCaB50g 5H20), and 10% ulexite (NaCaBgOg 5H20). The colemanite, along with boric acid and high-grade colemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder, which is the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content, which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations. Laboratory Calcination and Air Tabling Tests Laboratory calcination tests showed that substantial upgrading of the borate could be accomplished by calcining followed by screening of the calcined material. Removal of the + 28 mesh calcine resulted in borate losses of less than 10% with a rejection of 40 weight % or more of the calcine. The minus 65 mesh calcine generally met the requirement of containing 48%, or more, B203. The minus 28 plus 65 mesh material contained an intermediate quantity of borate and would require additional treatment. Testing demonstrated that ore would not have to be reduced to a size finer than 19 mm (3/4 in.) prior to calcination. A temperature range from 400 to 455OC (750 to 850°F) was apparently satisfactory. Calcination at a temperature of 48Z°C (900°F), or higher, was unsatisfactory due to fusion. All laboratory calcination tests were static tests conducted by placing small covered charges in a laboratory furnace for 40 min. In all tests vapor issues from the furnace for 5 to 7 min. Following this period the ore could be heard "popping," due to decrepitation of the colemanite. The reaction generally continued for approximately one-half hour. Various size fractions of the calcination products from laboratory tests were subjected to laboratory air tabling tests, usually after removing the plus 28 mesh material. Laboratory air tabling tests were conducted employing a Whippet V-80 model air table manufactured by Sutton, Steele and Steele Co. now known as Tripple S Dynamics. Variables include both end and side-tilt, speed of vibration, and quantity of air rising through the deck. In addition to the variables in the machine itself, the feed rate is also a rather critical variable. Testing demonstrated that all - 28 mesh size fractions of the calcine could be successfully concentrated to 48% F2O3 or greater. For the finer material recoveries into the concentrate were between 85 and 90% of the borate. With the coarser material a substantial amount of middling was produced which required cleaner tabling. Laboratory calcination and air tabling tests indicated a process whereby the borate could be concentrated to about 50% B203 with borate recoveries approaching 90%. Moreover, the iron content of the concentrate was well below the required specification of 0.3% Fe2O3. Pilot Plant Calcination Following the laboratory test work described above, pilot plant testing was conducted to prove the process, provide data for engineering studies, and provide product for a prospective purchaser. The kiln used was 0.9 m-diam (3 ft) by 9.0 m (30 ft) long and had a belly section 1.2 m-diam (4 ft) by 2.74 m (9 ft) long near the discharge end. The kiln was operated at a speed of 0.7 rpm. Gas was fired into the kiln at an average rate of 27.1 m3/hr (958.4 cu ft per hr). The air to gas ratio used was 10:1. The ore was fed to the kiln countercurrent to the flame and discharged through a hopper into a screw conveyor which discharged to a 1.2 m (48 in.) Sweco separator. The separator had 28, 65, and 150 mesh screen cloths, with the plus 28 mesh fraction being discarded. The minus 28 mesh fractions were later subjected to air tabling. The exit gases, containing some calcine dust, were swept through two cyclones to recover the dust. The gases then were scrubbed in a Ducon scrubber; very little dust reported past the first cyclone. The dust from the first cyclone was also saved in drums. In addition to the gas rate, the flue gas velocity, after

Jan 1, 1981