Search Documents

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968

By Blake M. Caldwell, Harrold D. Owen

The continued use of permanent-type, we11 completion Iras pointed LIP the need for more powerful through-tubing perforating equipment. A new expendable shaped charge perforator has been developed in which the charges are run through the tubing in a vertical position and then opened out to a horizontal position when at the desired shooting zone. The performance of this new tool is comparable to that of conventional casing type perforators. This paper describes the new tool and its applications. Performance data in targets rind under various actual well conditions are presented. INTRODUCTION The general acceptance and increasing use of pernianent-type well completion by the oil industry has indicated the need for through-tubing perforating equipment with performance comparable to that of conventional casing type perforators.'.' To achieve the performance desired, a new, expendable, shaped charge perforator has been developed with adequate power for effectively perforating both 51/2-in. and 7-in. casing below tubing. This has been accomplished without resulting severe damage to the casing and can he obtained under extremes of pressure and temperature. The design of this new tool is a radical departure from previous concepts of tubing guns since it was felt that the two major limitations imposed by previous designs severely handicapped performance. The first of these limitations was the restriction imposed upon the length of the charges by the necessary small inside diameter of the carrier. This resulted from the necessity for compromises in designing a hermetically sealed gun small enough to allow free passage through 2-in. tubing, yet with sufficient wall thickness to withstand some minimum pressure. In an effort to overcome this limitation, the charges were in some cases placed at an angle with the axis of the well with resulting loss in effective depth of penetration. The second limitation concerned the extreme distance of the charges from the casing when the gun was fired. An example of the latter situation is demonstrated by the fact that a conventional 13/4-in. tubing gun centralized in 51/2-in., 17-lb casing has a clearance of more than 1-9/16-in. on all sides. This means that a considerable portion of the force from each charge must be expended in penetrating this 1-9/16-in. of well fluid before it even reaches the casing. With the gun centered in 7-in., 23-lb casing, the amount of fluid penetration required of each jet is in excess of 21/4-in. In a situation where the 13/4-in. gun is touching one side of the 51/2-in., 17-lb casing, the jets from the charges on the opposite side have more than 3%-in. of fluid to penetrate. A similar situation in 7-in., 23-lb casing necessitates the penetration of more than 4-9/16-in. of fluid. The penetrating effect of the charges is severely impaired in passing through so much fluid. Under such conditions, there is usually insufficient force left to penetrate the casing. Previous studies have shown the decided disadvantage of having to shoot through such an excessive quantity of well fluid.'.' The problem. then, was how to position large powerful charges close to the casing prior to firing and still manage free passage through 2-in, tubing. The solution appeared to be in some method of folding sealed charge units in an open type, expendable. 13/4-in. carrier for travel through the tubing, and unfolding them upon their arrival at the shooting zone in the casing. It was desired to control the mechanism electrically from the surface through the regular shooting cable, making the release of the charges independent of the physical characteristics of the well, yet with a provision to prevent the gun from firing until the

Jan 1, 1955

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By W. Mckewan, W. M. Fassell

The oxidation rates of copper have been determined at temperatures from 600" to 900°C in oxygen from 14.7 to 400 psi total oxygen pressure. The oxidation rate of copper is unchanged by oxygen pressures within the range studied. The observed data extend Feit-knecht's conclusion concerning the pressure independence of copper from atmospheric pressure to 400 psi. All samples studied in the above-mentioned temperature and pressure range have both Cu2O and CuO present in the oxide film. NUMEROUS papers have been published on the oxidation of copper, some of which have noted the effect of oxygen pressure on the oxidation rate of copper. It must be noted, however, that no data on the oxidation rates of copper at pressure in excess of 1 atm have been reported in the literature. (Le Chatelier¹ reported that a black oxide of silver was formed at 300°C and 15 atm pressure.) This is likewise true for the other metals. This investigation was initiated to obtain experimental oxidation rate constants for pure metals at elevated temperatures and high oxygen pressure. Copper was selected as the first metal since probably more reliable data are available on its oxidation rates and related physical and chemical properties than for any other metal or alloy. As a general summary, the following conclusions appear well established for the oxidation of copper: 1—The oxide coating consists of Cu2O with a superficial coating of CuO providing the ambient oxygen pressure exceeds the equilibrium pressure for the coexistence of Cu2O and CuO.² The following sequence of phases is then Cu/Cu2O/CuO/O2 (gas). The Cu2O consists of large crystals that have no relation to the orientation of the metal crystals, except for a very thin layer adjacent to the metal." The CuO consists of very fine crystals randomly oriented. If the oxygen pressure is below the equilibrium pressure for the coexistence of Cu2O and CuO, the coating consists of Cu,O only. 2—The rate-determining factor in the parabolic oxidation of copper is the diffusion of Cu+ ions through the Cu,O layer.4,6,7 The Cu+ ions are accompanied by electrons to maintain electrical neutrality. The mechanism of the reaction at the Cu2O/CuO interface and the method of growth of the CuO is in some doubt. 3—On copper, there are three reported pressure effects: (a) At pressures below 0.3 mm Hg oxygen pressure, the oxidation rate increases directly with pressure.', ' .Vxygen starvation at the surface may account for this effect. (b) At oxygen pressures from 0.3 to 63 mm, the oxidation rate increases as the 7th root of the oxygen pressure providing the temperature is such that only Cu2O is present in the film. (c) At pressures from above the equilibrium pressure for the coexistence of Cu2O and CuO (varies with temperature) to atmospheric pressure, the oxidation rate is independent of the oxygen pressure.' Equipment In order to determine the oxidation rates of metals in an oxidizing atmosphere at pressures up to 400 psi, the equipment is somewhat different than for low pressure work as is shown in Figs. 1 and 2. A Leeds and Northrup Micromax recording controller (A) is used to control the temperature of the Ni-chrome furnace winding in conjunction with a Micromax electric drive unit. The drive unit adjusts a 20 amp Variac (variable transformer) to control the power input into the Nichrome furnace winding. Due to the "self heating" of the sample by oxidation, frequently encountered in oxidation rate studies, it is essential that the sample temperature be measured independently. This is done by means of a series of six chromel-alumel calibrated thermocouples located spirally around the oxidizing metal sample. Each thermocouple is partially shielded from the direct radiation of the furnace wall by

Jan 1, 1954

By J. Spreadborough, D. LaW. King, E. Anderson

Tmzsile tests were performed on Armco iron samples, at various ternpe.ralures and strain rates, ocer a wide range of grain sizes. Analysis of the data suggests that the plot of the lower yield stress, against d-1/2,where 2d is the acerage grain diameter, is not linear (as is often assumed) but is concave toward the d. axis over the range of d-from 7 to 53 . The different values of the parameters obtained by other workers can be explained, in part at least, by the observed curvature. This curvalure is shown to be consistent with a model of yielding based on dislocation pile-ups; however, the values of obtained by fitting our data to this model differ appreciably from the values generally reported. The equation proposed by Cottrell, viz.: is a plausible empirical fit to the experimental results. The purpose of this paper is to comment on the validity of the widely used linear relationship first proposed by all' and Petch and coworkers2"4 between ay, the lower yield stress, and 2d, the average grain diameter, for bcc metals, viz.: Many workers, see Refs. 2 to 7 and Table 11, have fitted this equation to their experimental results and have obtained acceptable fits over the relatively narrow range of grain sizes used by most of them. Indeed, in some cases, so few data points were available that any more sophisticated fit would have been irrational. In most of the interpretations,'-' oi is thought to be a measure of the friction stress accompanying dislocation movement, and ky was originally inter- preted as a measure of the dislocation locking but is now believed by Cottrell" to be a function of the dislocation creation rate. In the "unpinning" theories, k, is equated to where od is the unpinning stress and 1 is the average distance from the boundary of the grain where yielding is taking place to the nearest dislocation source in an unyielded grain. Other considerations (see, for example, Refs. 11 and 12) lead to equations with a similar form to [I] where different meanings may be attributed to the parameters. While there are doubts as to the physical significance of the parameters i and k, they continue to be used by many workers; interpretations of the variations in the behavior of ferrite materials following certain treatments, e.g., aging,'3 neutron irradiation,14 have been given frequently in terms of these parameters. Some theories of the mechanical behavior of bcc metals are based on this relationship. We have investigated experimentally the oy - d-'lZ relationship for Armco iron over a wider range of grain sizes and with more data points than those given in published results. The analysis of our data suggests that the oy—d-'" relationship is not linear but is in fact concave towards the d-'I2 axis. RESULTS AND DISCUSSION The experimental work was carried out on 3-mm-diam Armco iron rods which were prepared by wire drawing from 5-mm-diam rods. By annealing in vacuum at temperatures between 7000 and 1200°C for various times, grain sizes from 7 to 20,000 grains per sq mm were obtained, the grains in all cases being regularly shaped. Grain sizes were measured by lineal interceptand by area methods; only specimens with Amax/A values of 3 to 6 were used in the Petch-Hall plots (where A is the average area of a grain and Amax is the area of the largest grain observed). For all the specimens used, the number of grains in a cross section exceeded 50, which should be adequate to avoid grain size effects.'= Tensile tests were performed at 296", 219, and 17l°K, using

Jan 1, 1969

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

The subjects of this study are two corrosion phenomena familiar to operators of aluminum plants employing Soderberg anodes of the vertical type, namely the sul-fide scale formation observed at the steel contact spikes and the corrosion wear observed at the lower edge of the gas collecting skirts. The causes of these corrosion phenomena are discussed on the basis of observations from practice and measurements on commercial cells as well as on laboratory experiments. It is concluded that the anode spike corrosion is mainly due to the attack by sulfur compounds contained in the anodically evolved gases and that this attack is greatly promoted by cracks and pores in the anode carbon embedding the lower spike ends. The corrosion of the gas collecting skirt is mainly attributed to anodic dissolution of the iron during occasional contacts with the melt. ANODE SPIKE CORROSION The visible result of this corrosion is the formation of a brittle loosely adherent scale on the lower ends of the mild steel spikes maintaining the electric contact to the carbon anode, Fig. 1. The thickness of the scale usually varies from 0.5 to 3 mm, but in some cases scale of about 10 mm thickness has been observed by the writers. During the spike pulling, usually repeated every 3 weeks, part of the scale often loosens and remains in the anode carbon, resulting in contamination of the aluminum with iron. This corrosion has been attributed to reaction of the iron with gaseous sulfur compounds originating from the anode paste materials.'-4 This paste usually consists of 70 pct precalcined petroleum coke with 1.2 to 1.4 pct S and 30 pct coal tar pitch containing 0.5 to 0.7 pct S. During operation the gasification of the anode materials takes place in two ways: First, gases are evolved by the gradual baking of the anode paste added on top of the anode. Due to the sealing effected by the upper semifluid zone of the paste, these gases, containing sulfur compounds from the pitch, are forced downward through pores and cracks in the rigid anode carbon. At the temperatures of the zone of the lower ends of the spikes, 700" to 900°C, the original components of the baking gas must undergo decomposition, similar to that taking place with the production of coal gas, resulting in a gas mixture consisting mainly of H2 and CH4 with small percentages of H2S as the main sulfur compound.5 Second, the anodic reaction results in a mixture of C02 and CO, the total quantity of which is about 15 times that of the baking gas. These anode gases must carry the entire sulfur content of the carbon gasified by the anodic reaction. Henry and Holliday6 have shown that COS is the main sulfurous component of the anode gases from Soderberg cells. Soderberg anodes usually exhibit a network of vertical cracks, frequently traversing from one spike to the next one and to the outside of the block and widening downward to the working face of the anode. In addition the anode carbon, particularly that below the spike ends, is rather porous, as indicated in Fig. 1. It therefore seems probable that the anode gases also may partly penetrate to the spike ends. As the anode is partly immersed in the melt, the static pressure of this must forward this penetration. I) SPIKE SCALE COMPOSITION A great number of freshly extracted spikes from industrial plants were inspected and samples of the scale collected for examination. Before analyzing the samples a thin iron oxide layer, formed by air oxidation of the outside of the red hot scale immediately after spike pulling, was removed. On the average the Fe/S ratio found by these analyses corresponded to I the composition FeSl. oo7. X-ray powder patterns showed no oxide and otherwise agreed with those found by Haraldsen7 for iron sulfide with 50.00 at. Pct

Jan 1, 1970

By A. G. Guy

In a special type of electrodiffusion experiment the entire specimen is at constant temperature. The vacancies are then created at one end of the specimen and flow to the other end where they are destroyed. The energy required to operate the corresponding sources and sinks results in a super saturation of vacancies at one end of the specimen and an under -saturation at the other end. This gradient in vacancy concentration produces a chemical-diffusion flux, J(D), of vacancies in addition to the flux, J(E), caused by the electric current. Using the experimental data of Ch. Herzig,5 it is shown that a super saturation of 1 pct can cause J(D) to be about 25 pct of J(E), and thus account for the anomalous behavior of short specimens. THERE are advantages in a phenomenological treatment as contrasted to an atomistic one. For example, there are many reactions involving the element copper that are quantitatively and usefully understood from a phenomenological viewpoint, even though electron theory is not yet able to predict whether copper should be fcc or cph.' Similarly, the lack of a complete atomic theory of vacancies need not prevent the development of a treatment based on thermodynamics and chemical kinetics. In the following discussion, models will be used for the vacancies and for the mechanisms by which they move or are created or destroyed, but the phenomenological treatments are not dependent on the details of these models. The important product of a phenomenological analysis is an equation that describes the relation among the measurable quantities determining the behavior of the system. Based on such an equation, experiments can be performed to study these quantities in detail. Eventually atomic theory will supply an adequate theoretical base for the phenomena in question. A chemical species whose chemical potential was invariant during reactions in binary and ternary systems of varying composition would indeed be an anomaly. Yet this is the role that has frequently been assigned to the vacancies in pure metals, in dilute solutions, and even in ordinary alloys. The weight of available evidence supports the view that supersatu-rations of vacancies are on the order of 1 pct in usual diffusion processes.' Although it may seem strange that such a small deviation from equilibrium could significantly affect the thermodynamic properties of the vacancies, it is well known that the driving force for an ordinary chemical reaction is the departure of the components from their equilibrium state. Similarly, the reaction of vacancies that results in the formation of pores in various types of diffusion3 can reasonably be attributed to the supersaturation of vacancies. In the present paper, it will be shown that small degrees of supersaturation can significantly affect the kinetics of the diffusion process itself. ISOTHERMAL ELECTRODIFFUSION Two different experimental techniques are convenient for studying the behavior of vacancies in a pure metal in the presence of an electric field. Gilder and Lazarus4 studied self-electrodiffusion in a gold specimen in which only the central portion was at high temperatures. In this case the significant vacancy sources operate inside the specimen in the presence of a temperature gradient. In the laboratory of Th. Heumann a method has been devised for studying self-electrodiffusion at constant temperature.5 In principle, there is then no effect of thermodiffusion. It will now be shown why in this case the significant ATungsten disks \^^ ^^ ^Gold disks^^ ^^"T>.... "TTZA ? Up Iy'7 markers ///// ////// initial plane p I y/y/y of joining \I 7//// V7//A_________I_________V//// -I 0 +I Distance from center of specimen (a) -— Direction of flow of electrons —Direction of flw of vacancies %yy} Matano I z~irkendall /%W, vy/A inlerfacej "interface ///// -} HfiK- +/ 0 Distance from center of specimen (6) Fig. 1—-Schematic illustration of the essential features of isothermal self-electrodiffusion. (a) Initial condition of specimen. (b) Condition of specimen after electrodiffusion.

Jan 1, 1970

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1' that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By O. M. Schaus

REDUCED activity of mining, because of the business recession, had the effect of lowering working time, hence of reducing exposure to accidents, so it is probable that 1938 will be found to have had a lesser number (both fatal and nonfatal) though the accident rate may remain about the same as in 1936 and 1937. During periods of re-employment, such as occurred during 1936, 1937, and 1938, the new men entering the industry are less experienced and not as well trained in accident prevention as are the older, more experienced men and are frequently subject to more accidents. This situation should tend to correct itself as the new employees be- come better trained.

Jan 1, 1939

By H. J. LONGMORE

MORE improvements have probably been made in the diamond-drill field in the past decade than were accomplished in the entire prior period since diamond drilling was discovered in 1864 by a French engineer named Leschot. True, machines were improved, and new accessories were adopted from time to time up to 1929, but no radical changes were made. The basic principle instituted during the early years of the industry were still in use in 1929. At that time, practically the only diamonds used were "black diamonds" or "carbon." These came from Brazil through a rather round- about route, and by the time they got to the drilling trade their cost was excessive-$175 per carat and even higher at the peak. Perhaps because of this. or perhaps because of increased competition, the industry sought ways to reduce expenses even in the face of constantly increased labor costs due to higher wages and reduction in hours worked. The solution seemed to rest in two things-use of a cheaper cutting medium to replace the carbon diamond and the development of new machines to drill faster and thus produce more hole per shift of operation.

Jan 1, 1940

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

By Edmund E. Getzin

Of all the developments in the post-war history of Western Europe, none has been more remarkable in its aims and in the progress it has achieved than the movement toward European integration. It is not an exaggeration to say that this movement marks a virtual revolution, an about-face, in the long and complicated history of European states over the past three centuries. Although sporadic efforts to achieve European integration can be traced back for at least a 100 years, it remained for the breakdown of the European economies as a result of World War II and the subsequent Russian threat to give new impetus to the concept of broader economic and political integration. In fact, the economic integration of Europe following the end of the war was considered so essential that, in 1949, the administrator of the European Cooperation Administration, Paul Hoffman, spoke of the economic integration of Western Europe as an objective of American policy embodied in the Marshall Plan.

Jan 6, 1963

By Albert Hoskinson

PROGRESS on the earth depends to a large extent upon the rapid inter-change of ideas and commodities between the various nations of the world. The smooth flow of commerce, by which these ideas and com-modities move, is accelerated by accurate and complete maps of the various land and water areas of the earth, The production of accurate maps depends upon a complete knowledge of the figure and dimensions of the object to be charted, therefore a knowledge of the shape of the earth is a prime necessity for accurate charting purposes. Gravity observa-tions were first undertaken to aid in determining the shape of the earth so that the geodetic surveys of its land and water areas might be more accurately connected to form an undistorted map. A large part of the earth's surface is water and it is therefore necessary to get gravity values at sea as well as on land before a complete and accurate figure of the earth can be determined. Dr. F. A. Vening Meinesz, of Holland, was the first scientist to perfect a pendulum instrument that would accurately measure gravity at sea. He had previously developed a multiple pendulum apparatus for measur-ing gravity upon swampy and unstable land areas in Holland and it was therefore quite natural that he should adapt the instrument to give accurate results upon a still more unstable support, the surface of the sea. His instrument as perfected gives satisfactory results when mounted in gimbals on any vessel where the roll and pitch are not more than about 5° and where the vibrations from rotating machinery and wave action are not large enough to cause the pendulums to shift on the knife-edges. This degree of stability can be obtained on surface craft only in protected waters or on very calm days. Therefore, Dr. Meinesz mounted his instrument in a. submarine so that he could submerge below the disturbed surface waters and get the desired stability in nearly any kind of weather by simply diving to greater depths. Most of the gravity-at-sea work has been done with a Meinesz instrument and a very large number of the observations have been made by Dr. Meinesz himself. He has occupied nearly 1000 sea stations and probably has traveled as many miles by

Jan 1, 1938

By V 7. 0 / 300 dpi

DRILLING in the Oligocene potash basin of Alsace prior to 1927 had shown important differences of level in the salt beds thus encountered. To explain this a somewhat unsatisfactory hypothesis of faulting had been advanced. During the latter part of 1926 and the beginning of 1927- our firm was engaged by two organizations for the purpose of trying to supplement, by an electrical survey, the geological data thus far collected. As a re-sult of this exploration it was possible to affirm that salt dome structures were present in the Oligocene basin of the Upper Rhine, something heretofore absolutely unknown in that region. Two salt domes were actually outlined, one, near Meyenheim, was made the subject of a communication to the Academy of Sciences, by G. Friedel2; the other, near Hettenschlag, was briefly dis-cussed by C. and M. Schlumberger3 before the same academy. The purpose of this paper is to indicate the strati-graphic and structural conditions of the area where these salt domes were found; to discuss the results of the electrical survey which led to the location of the domes, and indicate the new geological outlook which such a discovery suggests.

Jan 9, 1928

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of the distribution of nodules on the seafloor and the location of economically important areas, but less effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic processes. It is not by coincidence, however, that the area considered to be most economically feasible is, in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are related indirectly, and possibly directly, to the activities of organisms.

Jan 1, 1983

By Frederick Laist

F. N. FLYNN, Clifton, Ariz.-I would like to ask Mr. Mathewson what percentage of his leaching liquor is wasted at this time? It has a bearing on the question in connection with the New Cornelia, and I think it is a very important question. E. P. MATHEWSON, Anaconda, Mont.-I am not sure what the percentage is now, but we don't discard the strong liquors. Something like 25 per cent. of the wash water taken out each day is sent over a special set of scrap iron tanks, and the copper recovered there. We had a little trouble at first. We did not proceed to use the sponge iron for the reason that the plant we originally contemplated was abandoned for flotation. Our original idea was to use a leaching process on all the tailings of the mill, but we found it would take a great deal of time to build a plant; and the cost of operating the plant we estimated to be about the same and the recovery the same. It was a question of time with us, and we decided to adopt flotation. That changed our plans. We now have the leaching plant, treating the tailings of the old dump, and the flotation applied to the current tailings. The sponge iron was figured for the large plant. We can get all the scrap iron necessary for the small plant-plenty from the scrap produced in the main plant of the smelter.

Jan 12, 1916

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By M. A. El-Aouar

Drilling muds are complex colloidal systems. In an effort to analyze the physical properties that affect their performance at high temperature, an investigation was made of the hydrothermal stability of the monoionic hydrogen, calcium and magnesium forms of montmorillonite and attapulgite. Samples were heated to 400°1F in a simple autoclave and analyzed for cation exchange capacity, c-axis X-ray diffraction spacing and pH factor us sodium hydroxide titration dependence. Out of the six monoionic clay minerals tested, calcium montmorillonite and magnesium attapulgite showed the least base exchange capacities and were relatively unaffected to heat. It is concluded that, of the six clays studied, these two clays were the most suitable forms for use in drilling fluids. INTRODUCTION The drilling of deep wells is dependent upon the drilling mud, and problems frequently arise concerning the effect of mud temperature and prolonged heating. Drilling muds are complex colloidal systems. In an effort to analyze their behavior in deep, hot boreholes, it was thought desirable in this investigation to study suspension of pure, monoionic montmorillonite and attapulgite clays before and after hydrothermal heating. Chemically, clays are hydrated aluminum silicates, such as montmorillonites and attapulgites. The structure of montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. Attapulgite consists of double silica chains running parallel to the c-axis with the chains linked together at their longitudinal edges. The apexes of the tetrahedrons in successive chains point in opposite direc-tions.4,7,10 One of the most important characteristics of clay minerals is their property of sorbing certain anions and cations and retaining them in exchangeable state. The property of exchange capacity is measured in terms of milliequivalents (meq) per 100 gm of clay. The cation-exchange capacities are taken at pH 7 from titration curves which show the relation between pH and milliequivalents of added NaoH.9,11 The following are causes of cation exchange: (1) broken bonds around the edges of the silica alumina units would give rise to unsatisfied charges, which would be balanced by adsorbed cations; (2) substitution within the lattice structure of trivalent aluminum for quadrivalent silicon in the tetrahedral sheet and of ions of lower valence; and (3) the hydrogen of exposed hydroxyls may be replaced by a cation which would be exchangeable. The primary techniques employed to study the effects of hydrothermal treatment were titration curves and X-ray diffraction analyses. Titration curves were useful in characterizing the nature of the clay mineral surface and the stability of the various samples to attack by acid or alkali before and after hydrothermal treatment. X-ray diffraction analyses were used to determine changes in the nature and crystal structure of the minerals present and to determine the cations in exchange positions on the montmorillonite samples. EXPERMENTAL PROCEDURE PREPARATION OF SAMPLES Selected samples of Wyoming bentonite and attapulgite clay from mines along the Georgia and Florida border were purified by centrifugation to remove all particles larger than 2 microns. In preparing magnesium attapulgite, first a 1.00-normal solution of magnesium acetate was prepared. The pH of the solution was adjusted to 7.0 by adding magnesium oxide. One hundred grams of attapulgite clay were mixed in a blender for 30 minutes with the magnesium acetate solution. The attapulgite solution was left overnight, and then filtered in a Buchner funnel. The suspension was leached with further quantity of magnesium acetate solution and then washed with distilled water for 20 days, after which the filtrate was free from magnesium ions. The concentration of magnesium attapulgite in the clay slurry was adjusted and determined quantita-

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921