Search Documents

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By John H. Hollomon

A REVIEW of the steps which have been made to increase knowledge in the field of ferrous physical metallurgy during the closing period of World War II brings both pleasure and disappointment. Contributions of great value have been made, to be sure. However, due partly to the stress of the times, researchers in this field have been in the main directing their attention toward the short-range problems involved in the development and production of materiel for war. Furthermore, publication of the results of a great number of studies has had to be delayed. Much of the German work may, indeed, be lost entirely, owing to the efficiency of our bombers, which managed to account for most of the famous Kaiser Wilhelm Institut of Dusseldorf, not to mention the other large laboratories and manufacturing plants throughout that country. It would seem safe to assume, however, that fundamental research in Germany had been forced to give way to the shallow, but more pressing, engineering problems of a country trying to avoid defeat. In Russia the picture has been clouded by the limitations imposed upon comunication; but this much does seem clear: Russia alone among the great nations of the world has maintained her long-range view and has continued to foster research of the most fundamental type. English workers; on the other hand, appear to have been able only to meet the demands of the pressing problems of war, and their studies have been of the short-range variety. That metallurgical research of any sort should have continued in France during this chaotic period in her history would seem impossible, but, amazingly, a small handful of scientists did manage to carry on their work, and it is to be hoped that more will be heard from them in the future.

Jan 1, 1946

By W. TRINKS

RAPID progress has been made in the automatic control of open-hearth furnaces in the past few years and many firms today\supply such control apparatus. It is somewhat surprising that so little was heard about open-hearth control up to about, 1928, and that thereafter the practice of automatically controlling open-hearth furnaces spread very rapidly. Before discussing the reasons for this it may be advisable to list the quantities that can be controlled. One of the easiest quantities to be controlled in the open-hearth furnace is pressure. The reasons for controlling it are plain. If there is excess pressure in the furnace, products of combustion leak out around .the .door and through all the cracks in the brick-work. The stability of the piers between the doors is seriously endangered, and front wall repairs become frequent. Furthermore, hot gases are lost that might be usefully employed in heating the checkerwork. If there is a slight vacuum in the furnace, cold air entering through the doors and cracks cools the interior, slowing down the reactions and making it impossible to secure the highest degree of preheat from the checkerwork.

Jan 1, 1931

By C Gunther

Mining examinations are of several kinds and the scope of the investigation depends in each case upon the purpose for which the examination is made. A formal examination of a developed mine is an expensive undertaking; from one to several months are allowed for the work according to the size of the property; many samples are taken; investigation is made of the geological features, including, perhaps, a topographical and geological survey of the surface; the metallurgical treatment of the ore is studied; finally, a determination of costs is demanded. Formal examinations are made for prospective purchasers or as a basis for the consolidation of several properties, and occasionally, in the owner's behalf, to verify the work of resident engineers, or to determine the readiness of a mine for equipment and the kind and capacity of equipment it shall receive. A formal examination of a mine should not be undertaken until a preliminary examination has shown that it is justified. It is regrettable that some engineers are in the habit of prosecuting long and exhaustive examinations of properties whose lack of merit should be, and perhaps is, apparent from the start, or of continuing their investigation long after an unfavorable result is seen to be inevitable. This wasting of a client's money is a species of trickery difficult to prove, and therefore the more contemptible. Preliminary examinations are precisely what the term implies, and are undertaken to determine the advisability of making

Jan 1, 1932

CONTENTS PAGE Rae, Colin C.-A Possible Origin of Oil. Discussed by S. Linker, Colin C. Rae... 2 Cottingham, Kenneth.-Subsurface Conditions on Portion of Arches Fork Anticline. Discussed by David B. Reger 6 Moyer, W. Irwin.-Time to Pay Out as a Basis for Valuation of Oil Properties. Discussed by H. J. Smith 9 Pogue, Joseph E.-Future Demands on Oil Industry of United States. Discussed by James O. Lewis 11 J. J. Walsh.-Coa-lmine Ventilation. Discussed by W. B. Daly, J. J. Walsh, R. R. Sayers, H. H. Stock, George S. Rice, James W. Paul, D. Harrington, T. D. Thomas 15 Longyear, Robert Davis.-Diamond-drill Sampling Methods. Discussed by Ira B. Joralemon, J. J. Rutledge, E. C. Harder 19 Joralemon, Ira B.-Sampling and Estimating Disseminated Copper Deposits. Discussed by J. Parke Channing, John E. Hodge, E.E. Hunner, B. B. Gottsberger, W. Y. Westervelt, W. O. Hotchkiss 20 Boericke, W. F.-Sampling and Estimating Zinc and Lead Orebodies in Mississippi Valley. Discussed by J. Parke Channing, Arthur Thacher 24 Daly, W. B. and Linforth, F. A.-Organization of Mine Sampling at Anaconda. Discussed by George A. Packard, W. B. Daly, B. B. Gottsberger 25 Norris, E. M. and Rahilly, H. J.-Mine Fires. Discussed by R. Dawson Hall, W. B. Daly, Frank Haas, D. Harrington, Robert E. Tally 26 Raymond, R. M.-Safety Practice for Hoisting Ropes. Discussed by B. F. Tillson, Graham Bright, Rudolph Kudlich, J. F. Howe, Robert Peele, H. G. Davis. 30 Howe, J. F.-Use of Wire Rope in Mining Operations. Discussed by Horace F. Lunt, J. F. Howe, B. F. Tillson 36 Tanner, W. N., and Jaccard, F. C.-Wire Rope and Safety in Hoisting at Butte Mines. Discussed by Horace F. Lunt, W. B. Daly, C. L. Colburn, William Kelly, Robert Peele, B. F. Tillson, Graham Bright, Charles E. Locke 38 Richardson, A. S.-Ventilation of Butte Mines of Anaconda Copper Mining Co. Discussed by D. Harrington, Chas. A. Mitke 42 Stuart, Charles E.-Storage-battery Locomotive as Applied to Mine Haulage. Discussed by Howard N. Eavenson, Charles E. Stuart, William Kelly, Arthur Thacher, W. H. Patton, Graham Bright 45 Woodward, C. D.-Electric Haulage Systems in Butte Mines. Discussed by William Kelly, Graham Bright, Howard N. Eavenson, C. E. Arnold, Gerard B. Rosenblatt, K. A. Pauly 47 Harrington, D.-Efficient Ventilation of Metal Mines. Discussed by R. E. Simpson 52 Otagawa, Masayuki.-Mining Methods at the Ashio Copper Mine. Discussed by Horace V. Winchell, D. W. Brunton 52 Stoek, H. H. and Clagett, Thomas H.-Coal Mining Methods. Discussed by P. D. Browning, G. L. Cox, Erskine Ramsay, Frank Haas, George S. Rice.

Jan 6, 1922

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

HEAT-RESISTANT alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:12 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to 1.o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage II) of one per cent in ten thousand hours as extrapolated from rates per hour or tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at 1800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,1 in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably dose, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By W. F. Kieschnick, and W. J. McGuire&apos, Eugene Harrison

This paper concerns the induction and extension of fractures into rock formations as involved in drilling, completing, and production stimulating operations on wells. Conclusions concerning formation breakdown are derived from (I) a review and extension of published analyses relating to mechanical theories of rock stress and the state of stress in the earth's crust and (2) a correlation of field data from fracturing operations. Conclusions concerning the mechanics of fracture extension, which indicate the relationship between fracture dimensions and rock properties, depth, and volume of injected fluid, are tentative and largely establish limits of relationships. These conclusions are derived from stress calculations, limited field data, and laboratory experimental studies. The experimental work involves the study of the stresses at the fracture boundaries and the geometry of pressurized fractures by means of photo-elastic modeling methods. Results of this investigation indicate that a large majority of pressure induced wellbore fractures are vertical, particularly in deeper wells; and variations in the pressures necessary to create and extend fractures can be explained largely on a basis of established rock properties. It is also shown that variations due to tectonic forces should usually be expected to be slight. Other results indicate that during that extension of fractures rather large fracture volumes are temporarily created by the parting of the formation. The purpose of this paper is to present the results of calculations and laboratory experiments concerning the mechanics of fracture induction and extension with a view to broadening existing knowledge relating to these phenomena. It is believed that continued progress in developing knowledge of this type is important to the further development of techniques for drilling and completing wells. When a wellbore is subjected to sufficiently high pressure, fracturing of the formation surrounding the well occurs. This phenomenon is a common cause of lost circulation during drilling operations, is a deliberately planned factor in most squeeze cementing operations, and is the controlling factor in many productivity stimulation operations. The exploitation of formation fracturing in recent years has been particularly impressive in sand-viscous fluid well stimulation treatments which were first introduced to the industry by the Stanolind research group1,2,3 several years ago. The borehole fracturing phenomenon has been analyzed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of homogeneous, isotropic, and impermeable material.1,5,6 This basic argument is re-presented in this paper along with new considerations which strengthen it. In addition to these arguments relating to fracture induction some calculations and experimental results relating to the mechanics of fracture extension are presented. Since the nature of the pressure induced fracture at distances from the well is of great importance in considerations of well stimulation procedures there appears to be a need for an integrated approach which deals with the mechanics of fracture extension as well as with wellbore rupture.

Jan 1, 1955

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By John J. Collins

Page Purpose and scope..................... 521 Core sampling......................... 521 Sludge sampling....................... 527 Combining core and sludge assays ...... 533 Deviation and surveying of drill holes. . . . 537 Conclusions........................... 544 Acknowledgments...................... 545 Bibliography.......................... 545 Purpose and Scope The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described,25,26,31,32,50,65 but more informa- tion is needed on the results shown by actual mining operations. Core Sampling The accuracy of diamond-drill-hole Sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says; in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change; often indicated by a color change in the sludge water, should be a a for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By N. H. Darton

In the coastal plain region of the middle Atlantic slope there are no large supplies of potable surface-waters. The great rivers by which the region is intersected are tidal estuaries, and the water of their local branches is often of bad quality. The cities situated at intervals along the western margin of the region obtain a plentiful supply of excellent water from the rivers above the tidal estuaries, but out on the coastal plain surface-waters are mainly used. A few artesian wells have been sunk which afford abundant water, but their number is at present very limited. Norfolk, Newport News, and the many smaller places use surface-waters, and all over the region there is great need for purer and more abundant supplies. During the past five years I have been engaged in a study of the geology of the coastal plain for the U. S. Geological Survey, and have given special attention to the question of subterranean waters. In this communication I shall present a brief review of the geological conditions under which such waters occur in this region, and give an account of the wells which have been bored. Unfortunately the number of well-records is small, and some of the most important questions of subterranean geology are as yet far from settled. It is hoped that this paper may lead to further borings, especially as the cost of artesian wells has been much reduced by the introduction of new machinery and methods, and is now quite within the reach of the average community. In New Jersey there are many wells, and the water-bearing horizons are so definitely determined that they may almost everywhere be predicted with certainty. In Maryland and Virginia the data are less definite, but there is excellent evidence of a wide distribution of water at moderate depths.

Jan 1, 1895

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By E. A. Gulbransen, W. S. Wysong

The behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance. The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotec-tive nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance studyl, 2 of the following problems: (I) the oxidation kinetics in the temperature range of 250°to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films; and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 2 50°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide Moo3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics: time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation. The general interpretation of many of these factors has been previously discussed. Literature The oxidation of molybdenum has not been studied critically. Although many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Gulbransen." Their results showed that Moo2 is the oxide which is stable in contact with the metallic substrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Moos is no longer observed, MoO2 being the only oxide found. Hagg and Magneli6 have shown from an X ray study that the a-phase, orthor-hombic Moo3 is stable up to 1050°C. Two other phases, ß and ß with compositions close to MoO2.90 are also obtained. The formula for the 0 phase is not given but that of the ß phase is defined as Mo9O26 The 0' phase is found to be built upon a monoclinic unit cell. A ?-phase is isolated from a preparation MoO2.75 heated for 17 hrs at 670°C. This phase is

Jan 1, 1949

By R. H. Pemberton

The principle of airborne electroniagnetic prospecting is well-known. 'The basic geonhysicai texts in inost cases discuss the main elements involved in electromagnetic prospecting. However. there is ceriainlv iittle information available to the public concerning he present types of airborne eiectromagnerlc systenis being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficuit for those people not conducting such operations to understand thoroughly the iarge variation in the electromagnetic instrunlents available. Basically, the aeriai electromagnetic induction method utilizes a primary or transmitting coil through which is generated an alternating magnetic field at a frequents: generally of the range of 100 to 2000 cycies per sec. This primary field links with buried conductors and generates eddy currents within them. These eddy currents in themselves generate a secondary magnetic field of the same frequencv, but generally nut-of-phase with respect to the prinlarv field. This secondarv field is detected above the ground in the pick-up or receiver coil which is tuned to the frequency of the current applied to the primary transmitter coil. One of the main problems in the development of an airborne electromagnetic system is that of maintaining constant coupling between the cransmitting and receiving coil systems. Any variations in the coupling due to relative motion between the two coils will result in an in-phase signal being induced in the receiver coil. [However, any variation in the coupling does not result in an out-of-phase signal change in the receiver coil. The first airborne eiectromagnetic svsteins which were developed utilized a large prlniarv coil set up on the aircraft with the receiving coil being towed behind in a bird, generally at the end of a cable of about 500 ft. in length. It is possible with such a system to record the out-of-phase or quadrature responses more readily than the in-phase re-sponse. One system utilizes a dual frequency method, wnereby the out-of-phase responses at two frequencies are recorded. Another system used today records a single-frequency olrt-of-phase response. Recentlv home companies have succeeded in measuring from ne air both the out-of-phase and the in-phase components. The usefulness of recording in-phase is weil-known, but unfortunately this is difficult to obtain in any towed-bird system. In order to measure the true in-phase signal, the most straightforward system is that in which both the transmitter and receiver coils .Ire affixed in space so that there is little or no relarive motion between the two coils. THE FLIGHT SYSTEM The particular system which Canadian Aero Service is using at present is mounted on a Sikorsky S-55 helicopter (Fig. 1). A record of both the in-phase and out-of-phase responses is made at a frequency of 390 cycles per sec. The transmitter coil is set on a boom mounted in the front of the helicopter; the receiver is set on a tail boom extending back from the helicopter. Separation between these coils is about 65 ft. The two coils are mounted in a vertical co-axial relationship. Having the transmitting coil in a vertical plane ensures that maximurn coupling will occur with vertical conductors rather than flat-lying conductors. Having them mounted as they are in a co-axial relationship on the helicopter ensures that maximum response will occur when the flight direction is orthogonal to the strike direction of a given conductor. The present sensitivity of the Em system is 20

Jan 1, 1961

By R. F. Weber

The relation between the chemical composition and the refractoriness of fire-brick has long attracted the attention of manufacturers of fire-brick and others interested in their use, yet but little systematic work has been done along this line, especially in the United States. Analyses of fire-brick have been quoted for years, but fire-tests of brick, except those of durability in practical use, have usually been lacking. Although many tests and analyses of foreign fire-brick have been published, only a few have appeared in the United States; and even in the foreign literature, the references and facts are more or less scattered. The most elaborate foreign paper on the subject is that by Dr. Jochum.' One of the earliest, and perhaps the most detailed piece of work in the United States, is that of F. Platt, which was done for the Pennsylvania Geological Survey, in 1876.2 His investigation consisted of the analysis and heat-tests of 21 bricks, the testing being made in an experimental shaft-furnace at Har-risburg, Pa. All the bricks were more or less affected at the temperature reached, which was considerably higher than the melting-point of steel. The exact temperature at which individual bricks fused was not ascertained, hence the comparisons quoted in the paper are of value only for the bricks used in the test. The next comprehensive investigation, made by the New Jersey Geological Survey,³ deals chiefly with fire-clays; analyses and refractory tests having been made of 123 clays, kaolins, feldspars and fire-sands. Here; again, there was no accurate means of measuring the temperature, the only measurement of

Jan 1, 1905

By G. J. Saulnier, K. E. Goddard

The US Geological Survey has developed mathematical modeling techniques to assess potential impacts on the hydrologic system resulting from mining of coal and oil shale in northwestern Colorado. Potential impacts of oil shale mining on groundwater hydrology have been simulated using a quasi-three-dimensional, finite-difference model. The model has been used to simulate hypothetical mine dewatering operations at two proposed oil shale mines. Dissolved-solids distribution and solute transport were simulated with a three-dimensional, finite-difference model that was used to evaluate the effects of flooding in hypothetical abandoned mines. The potential impacts of coal and oil shale mining on water-sheds were investigated using a digital watershed model. This deterministic physical-process model predicts responses of the hydrologic system to modifications resulting from mining in basins having snow as the major source of runoff and recharge. Potential impacts of coal development on surface water quality were investigated using a river quality assessment model. The models developed by the US Geological Survey have been useful in defining the potential effects of mining in northwestern Colorado. They are an important first step in analyzing the existing data base and in predicting impacts and new data needs. The models may not be totally applicable on the local scale but are very meaningful on the regional level.

Jan 1, 1983

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957