Search Documents

By J. Chipman, J. C. Fulton

Reduction of Si from slag to carbon-saturated iron is a very slow reaction. The rate is nearly independent of stirring but is accelerated markedly by increased temperature. In a slag containing 45 pct SiO2, 38 pct CaO, 17 pct Al2O3, the energy of activation is approximately 130 kcal. AT temperatures of 1450" to 1600°C occurring in the hearth of the iron blast furnace, chemical reactions are normally expected to proceed with great rapidity. Many of the reactions of iron making are indeed quite rapid and attain a condition corresponding roughly to a state of equilibrium before metal and slag are tapped from the furnace. The one conspicuous exception is the reaction by which carbon in the coke or metal reacts with silica in the slag to deliver silicon to the metal. From the practical viewpoint the slowness of this reaction is indeed fortunate, for if it were fast enough to reach equilibrium during the time of contact, it would be difficult to produce pig iron of the desired low silicon content. The one other reaction which under certain circumstances can also be very slow is the transfer of sulfur from blast-furnace metal to slag. In their laboratory exeriments on this reaction, Hatch and Chipman found that at least 5 hr were required for the attainment of equilibrium in a small crucible and that the reaction was not accelerated by increasing the rate of stirring. Subsequently it was shown2 that the presence of a reducible oxide MnO greatly inhibited sulfur removal, and finally that SiO2 itself3 under some conditions has sufficient oxidizing Dower to interfere with sulfur transfer. The kinetics of sulfur removal are now rather well understood,4 and it has been shown3,5 that when the silicon content of the metal is high enough to prevent reduction of SiO,, the desulfurizing process is rapid. Thus the observations of slow removal of sulfur are associated with the coincident slow reduction of SiO2, a process which transfers both silicon and oxygen to the metal phase. It is, of course, the oxygen which interferes with sulfur removal. An explanation of the slowness of the silica reduction reaction has not been obtained. The sulfur transfer process has been shown by the authors5 to be at least partially transport-controlled in the absence of interference by silica. Under the experimental conditions. 99 pct of the total transfer at 1600" was accomplished within an hour. Under similar conditions the reduction of silica may not proceed half-way to equilibrium6 in 8 hr. It is scarcely imaginable that silica reduction could be transport-controlled when the slag contains 44 pct SiO2 and the metal about 1.4 pct C. The experiments reported here show definitely that it is controlled by a slow step or steps in the chemical reaction. One might expect to find such a slow step in the breaking of SiO bonds or in the slow removal of oxygen by carbon at the slag-metal or metal-crucible interface or by bubble formation. EXPERIMENTAL PROCEDURE The experimental procedure used in this investigation was similar to that used in the study of the kinetics of desulfurization.5 A sketch of the graphite crucible and stirrer used in the current work is shown in Fig. 1. The quantity of metal and slag used was adjusted so that the slag-metal interface was located between the top and bottom blades on the stirrer; the top of the slag layer was above the top blade. The stirrer shaft was hollow down to the metal level and served as thermocouple well or optical pyrometer target. Stirring speeds of 0 to 500 rpm were used. A carbon monoxide atmosphere was maintained in the furnace by flushing the gas over the slag surface, except in run No. 220 when it was bubbled

Jan 1, 1960

By E. Amott

A test is described in which the wellubility of porous rock is measured as a function of the displacement properties of the rock-water-oil system. Four displacemet operations are carried out: (I) sponlaneous displaceti?ent of water by oil, (2) forced displacement of water by oil oil in the same system using a centrifuging procetllrre, (3) spontaneous displacement of oil by water. and (4) forced displacment of oil by water. Ratios of the spontaneous displacement volumes to the total displucenlent volumes are used as wettability indicates. Cores having clean mineral surfaces (strongly preferentially water-wet) show displacement-by-waler ratios approaching 1.00 and displacement-by-oil ratios of zero. Cores which ([re. strongly preferentinlly oil-wet give the reverse resu1ts. Neutral wellability cores show zero values for both ratios Fresh cores from different oil reservoirs have shown wettabiltties in tlris te.st covering rrlti~ost 111e conlplrtt, range of thr: te.st. Notvever, nlo.s/ of tlle fresh California cores tested were slightly prcfere111icrlly wclter-\vet. The chrrnge.~ in coro u ('liabilities, as indicated hy this te.st, r~.sril/ing from various CO~P hanrlling procedures tt,ere oh.served. In sonie ca.sc,s /Ire ~,cttahilitio.c. of fresh cores were changell by drxi:~g or 11y e.x/rclct ing with iolcreiii~ or. dioxunc~; in o/h~r cases they were 1101 changed. Co~ltrrc/ of cort,.s ~.ith filtrc~t~c. from water-base rlrilling rilrrrls crlrc.sed littlc change in we/ /ahility ivhile contnct with filtrates frorii oil-hus~ ri1rlcl.s tlecrrascrl the prefcrerlcc, of the, cores for )I.NI Usitig thi,s test to ri.crl~lute n~r~ttubili~y, N .vt~ldy was iilarle of /lie correlmtio~i of wettability with wa/erfloocl nil recovery for orttcrop Ohio sand.stone and for Al~ln-tlunl. Resul/.v indicate thml no single correlatioti between these factors applies to different porous rock syste~n. It is thought that diflerences in pore gen~netry resrrlt in diflrrerrce.~ in this correlurio~z. INTRODUCTTON Most investigators who have reported on the wettahility of porous rock have described such rock as prcferentially water-wet or preferentially oil-wet. In some cases a third classification, neutral wettability. has been used. The efficiency of water floods in each of these wettability groups has been described in numerous publications. Several methods for characterizing porous rock wet tability more precisely have been reported,' " but it appears that because of one weakness or another. none of these has been generally accepted. Early in our studies in this field, it was found that the displacement efficiency of oil by water in a particular porous rock having a strong preference for water was quite different from that in a similar rock having only a moderate preference for water. Thus, there appeared to be a need for a practical, reasonably precise wet tability test. one which could classify porous rocks into 10 to 20 different groups rather than the two or three broad groups listed above. The test developed to meet this need is described in this paper. Also, changes in wettability, as indicated hy this test, resulting from various core handling procedures are discussed. Finally, data showing the corrclation of wettability with waterflood oil recovery for two different types of cores are presented and discussed. Some confusion has resulted from the failure of certain writers to define clearly some of the wettability terms they have used. Accordingly, the following commcnts concerning definitions are offered. The wc t ta-hility of a solid surface is the relative preference of that surface to be covered by one of the fluids under consideration. It is felt that this is the generally accepted definition. The fluids being considered must bc specified (or understood) before the term wettability has any significance. In the work reported here these fluids are water (3 per cent brine) and oil (kerosene). The term preferential wettability is sometimes used, but we think that the word preferential is redundant here and should not be used. Tn line with the definitions of Jennings', a preferentially oil-wet solid surface is regarded as a surface which will show an oil advancing contact angle less than 90" (measured through the oil) in the water-oil-solid system. Oil will spontaneously displace water, if both are at the same pressure, from such a surface. A preferentially water-wet surface is analogous. This is consistent with the wettability definition above. As Jennings has said, frequently the term oil-wet is used to mean the same thing as preferentially oil-wet. However, oil-wet also has been used occasionally referring to an oil-covered surface when the availability of water was limited. To avoid confusion from this source, we do not use the terms oil-wet and water-wet. DESCRIPTION OF WETTABTLITY TEST The following points were considered desirable in a wettability test for our purpose. 1. The test should be a displacement test resembling

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By J. R. Thoenen

THE consensus of opinion in the published literature on. Grecian magnesite is that it has been formed by alteration of the serpentine, which in turn was itself a product, of metamorphism from the original olivine intrusion. The general opinion seems to be that the magnesite was formed by descending waters heavily charged with CO2. Inasmuch as this opinion is held by engineers far better qualified than I to speak authoritatively on this subject, I hesitate to dispute that theory. However, certain occurrences coming under my observation do not, to me at least, seem to-entirely substantiate this theory. LOCATION Most of the Grecian magnesite comes from the Island of Euboea, although more recently some deposits have been opened on the mainland near the City of Saloniki, which prior to the war was Turkish. The island, comprising a state or province in the Greek political structure, is roughly 110 miles long and varies from 10 to 30 miles in width. It lies off the east coast of the Greek peninsula in the AEgean Sea with its long axis extending in a northwest-southeast direction. It is separated from the mainland by a long narrow arm of the sea known as the Atalanti Canal. Chalkis (Halkis), the capital on the west coast of the island, is the northern terminus of a branch of the state-owned railway and is connected with the mainland by a single-span, movable, highway bridge, roughly 150 ft. long.

Jan 1, 1928

By P. T. Stroup

Jan 1, 1964

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948

By Charles M. Rolker

The main tin-producing regions of the world are known to be England, Australia and the Dutch East Indian possessions, chiefly Banca and Billiton. During recent years, the tin of the Malay Peninsula, exported from Penang and Singapore, has been coming prominently to the front. France, Austria, Hungary, Germany, Spain, South America, Russia and China still present insignificant figures. The conspicuous part which the Dutch possessions in the Indian Archipelago have taken in supplying the world with tin, is well known. Tin was discovered in Banca as early as 1710, and has been produced there ever since; but the supply has been most important since Banca came fully into the possession of Holland, in 1821. In Billiton and the adjoining island of Singkep, the existence of tin was known prior to 1822.* The Lingganese knew of its existence in the valley of Embalong, from creeks and streams in the neighborhood of Tima and Simper hills, on Billiton and also on Singkep island, but the prevailing superstition that tin-mining brought misfortune, influenced them to let this industry lie idle. The attempts of the Dutch government to test this question were lukewarm, perhaps by reason of the fear of reducing, through new discoveries, the price of Banca tin, and the island was abandoned in 1826, leaving only a military post. In 1850, Dr. Crookewit, a chemist and naturalist, was sent out to verify the rumors that tin existed in Billiton. His report was unfavorable; but in 1851 Mr. C. De Groot, a mining engineer, found tin readily, and the active work on Billiton dates from that time. Less than 600 tons were produced during the first ten years, and 3000 tons in the next decade. Billiton tin-mining is done by

Jan 1, 1892

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y' phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS' showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969

By M. Mills, M. W. Clegg

This Paper Presents an approximate analytical solution to the problem of the pressure distributions arising from the production of a compressible liquid in a partially penetrating well. The limits of validity of the approximation are discussed and it is shown that the basic approximation is the same as that used in previous numerical of the problem. The variation in pressure at the production well with time for different penetration ratios is investigated and is shown to agree with previous work. The solutiOns are used to assess the effects of partial penetration at large distances from the well and at the wellbore itself. In the latter case the effects of anisotropy are also studied for constant, but unequal, horizontal and vertical permeabilities. It is 'uggested that measurements of the Pressure drawdown below the producing interval in a well should give some indication of a thickness-vertical permeability product for the formation; this would chmacterize the effectiveness of the formation below the producing interval. INTRODUCTION In many oil and gas reservoirs the producing wells are completed as partially penetrating wells; that is, only a portion of the pay zone is perforated. This may be done for a variety of reasons, but the most common one is to prevent or delay the intrusion of unwanted fluids into the wellbore. This paper studies the effects of partial penetration on the pressure distribution resulting from the production of a compressible liquid at a constant rate. To simplify the mathematical analysis the case of a single well located in an infinite reservoir of constant thickness is considered, and it is assumed that this well is perforated over an interval adjacent to the upper (or lower) impermeable boundary of the formation. A well producing from an arbitrary interval within the bulk of the formation could be treated in a similar way, but this action would merely add to the complexities of the solution and contribute little to the appreciation of the over-all effects of partial penetration. In a recently published paper by Odeh,10 the more general problem of producing from an arbitrary interval within the pay zone was studied for the quasi-steady state flow of a compressible liquid, This is the case in which there is a a potential at the outer boundary and a constant flux across the same boundary. This contrasts with the problem studied here, which is concerned with the nonsteady-state behavior in an infinite reservoir. The exact solution of the partial penetration problem presents great analytical problems because the boundary conditions that solutions of the partial differential equations must satisfy are mixed; i.e., on one of the boundaries the pressure is specified on one portion and the flux on the other. This difficulty occurs at the wellbore, for the flux over the nonproductive section of the well is zero, and the potential over the perforated interval must be constant. In the case of constant rate production from the well, this uniform potential is time dependent and unknown, and the additional condition that where hl is the thickness of the perforated interval, must also b'e satisfied. This problem may be overcome in the case of constant rate production by making the assumption that the flux into the well is uniform over the entire perforated interval, so that on the wellbore the flux is specified over the total formation thickness. This approximation naturally leads to an error in the solution since the potential (pressure) will not

Jan 1, 1970

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing' steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850'F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1' With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects'-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By R. R. Byran, M. H. Kuryla

The Compania de Real del Monte y Pachuca started a 10-ton pilot plant in March, 1906. The distinctive features of the first cyanide installations at Pachuca were: grinding in cyanide solution, all-sliming and filtration of ore in which silver constituted the major value. Loreto started with a 300-ton " all-sliming" plant, using jaw crushers, grinding in stamps, Chilean mills and pebble mills in cyanide solution, concentrating with Wilfley tables and Johnson vanners, classification by cones and Dorr classifiers, intermittent thickening by decantation, mechanical agitation in flat tanks by stirrers and centrifugal pumps, filtration in Butters filters and precipitation by zinc shavings. The "San Francisco" mill No, 1 was contemporaneous, using a rather similar flow sheet. We shall trace the main developlnents in the three large mills of the district to their present practice. Developments in Large Mills of District Crushing and Grinding.—The trend of development in this part of the work has been the same as throughout the milling world; via., all increase in the degree of comminution of the ore in dry-crushing machines, the advance from pebble mill to rock mill and then to ball mill and the elimination of the stamp battery through the encroachment upon its field on the one side by finer dry crushing and on the other by more efficient wet grinding. The single-stage crushing in jaw type crushers, used at the start, has been replaced by two stages; at first, both stages by gyratory type and later the present practice, which is the same in all three mills, consisting of gyratory as primary followed by cone as secondary and delivering a product that may be rated at 56 to 1 inch. Primary wet grinding, at first performed by stamps and Chilean mills, is now by hall and/or rod mills; present practice differing widely in the three mills. Santa Gertrudis uses a 7 by 15 ft. rod mill, San Rafael

Jan 1, 1935

By AIME AIME

THE organization of the Board of Directors was effected Tuesday afternoon in ' executive session. Messrs. Bassett,. Buehler, Cates, Daveler, Eavenson, Eilers, Elliott, Evans, Guess, Lovejoy, Moulton, Rickard, Tally, Turner,, Wraith and Wright being pres¬ent. Messrs. Tally, Bassett, Rickard, Mathews and Cates were chosen to form the Executive Committe with Mr. Tally as Chairman, and Messrs. Krumb, Guess and Moulton for the Finance Committee with Mr. Krumb as chairman. Karl Eilers was reelected as Treasurer and H. Foster Bain as Secretary, after which the Directors adjourned for the usual dinner reported elsewhere. At the open session of the Board, at which in addition Messrs. Allen and McAuliffe were present, the work of organization was continued with appointments to committees as listed herewith. Various actions of the Executive and Finance Committees were confirmed, the budget for 1931 formally approved, the meeting dates for the year adopted, 34 new Members and Associates, 13 Junior Members and 31 Student Associates admitted by election and transfer and 29 resignations accepted.

Jan 1, 1931

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By Henry D. Hibbard

These impurities are perhaps the most important things in steel—especially steel made by the oxidation processes—the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished ar at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of' the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in conlmercial steels. The microscope aids more, perhaps, than chemistry in their study.

Jan 1, 1911

By Charles Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with' respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding; or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that' one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short-discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding-plane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They' are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By A. Cochardt, D. H. Feisel

HE success of the sintered aluminum powder material (SAP)' in raising the maximum useful temperature of aluminum alloys has stimulated effort in investigating similar systems in which the metallic matrixes have higher melting points. Examples of such systems which have been studied are nickel-alumina,2, 3copper-silica,4 copper-alumina,4 titanium-cerium oxide,5 and 80/20 nickel-chromium,8 cobalt,= and molybdenum7 matrixes with various hardeners. Conventional precipitation-hardened high-temperature alloys are often thermally unstable in service. The original fine particles that are responsible for good strength properties grow in size at elevated operating temperatures, a process termed "over-aging." This growth of precipitated particles causes a gradual loss in strength properties. A previous paperb describes the factors that govern the process of overaging, and estimates the time required for overaging of a nickel-alloy matrix dispersion-hardened by various precipitates such as are found in current high-temperature alloys, and by alumina. These calculations indicate that nickel-base alloys hardened with Ni3Al, Tic, or TiN are quite unstable at 1340" F (727°F). Such alloys should overage within a few hours at that temperature. A nickel-base alloy hardened with alumina, on the other hand, should behave differently. It should not overage appreciably within a thousand years. It was further shown8 that the thermal stability of the oxide-hardened alloy is mainly due to the low solubility of oxygen in equilibrium with alumina in the nickel-base matrix. Since the oxygen solubility is small, little oxygen can diffuse, and structural changes require very long times. This paper illustrates the effects of time and temperature on the structural stability of nickel alloy matrixes hardened by dispersions of Ni3A1, Ni3Ti, Tic, and alumina, and of nickel-chromium matrixes hardened by alumina. Hardness measurements and metallography have been used as a measure of structural stability. EXPERIMENTAL PROCEDURE Using the best information from published phase diagrams,'-l4 compositions of the Ni-Al, Ni-Ti, and Ni-Ti-C alloys were determined so as to have 5 vol pct of precipitate at 1350° F(732°C), the temperature selected to illustrate the effect of time on structural stability. Table I lists the chemical compositions of these alloys. Standard laboratory melting and alloying techniques were used in preparing ingots of the F-Series of alloys. The cast ingots, 1 3/4 in. in diam, were forged to 3/8-in. diam rods.

Jan 1, 1960