Search Documents

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.' Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970

By David, Cole

THE years 1914-15-16 were a pioneering period in mining, milling, and copper metallurgy generally. It was uncertain just what path the crushing, grinding, and concentrating processes would take. This situation was quite embarrassing to the directors of some of our large porphyry properties, then being equipped for production. Inspiration had already made several designs for its proposed 15,000-ton concentrator, incorporating in them the latest devices developed in the art of gravity concentration, only to have the work vitiated by the rapid march of events. In a little improvised plant, built on ground that is now in the crater of subsidence over the Inspiration- Miami orebodies, flotation was being experimentally ' applied to Inspiration ore by Minerals Separation engineers in 1914, with results indicating that this process would be of major importance in the concentration of the sulfides. How best to apply it, and especially how to crush and grind the ore to the very much finer sizes required for the new process, was a serious question, properly to be answered only by doing it, in full- sized machines, under regular 'operating conditions.

Jan 1, 1931

ARIZONA Established July 10, 1915 ROBERT W. THOMAS. Chairman ROBERT W. HUGHES, Vice-Chairman HUBERT O. WOODS, Secretary-Treasurer American Smelting & Refining Co., Hayden, Ariz. LYLE BARKER M. G. FOWLER RICHARD BRITTAIN M: C. HENRIE B. S. BUTLER F. D. 1. HONEYMAN T. G. CHAPMAN J. E. LANNING C. H. COLE A. MENDELSOHN G. C. DAVIS BRENT N. RICHARD E. Ii. DENTZER C. F. WILLIS

Jan 1, 1943

By Meissner, C. A.

THE tendency all over Europe, just as it is with us, is to go to the use of turbines for new construction or replacement of old steam or even gas engines. 'The lower construction cost and the lower operating cost, when they can have high steam temperatures and pressures, together with their efficiency, is the cause of this change to turbines, both high and low pressure. The present trend is to equip plants with modern, efficient steam boilers, turbines, etc., and gradually work into high-pressure superheated steam equipment to accomplish a saving. One company has just completed a 375 to 400 lb., 700 deg. superheated steam installation and turbo-blowers with this end in view. Some of our new steam plants are using 350 lb. working pressure.

Jan 1, 1928

By Earl C. Willis

In selecting new or replacement mining machinery to be purchased, there are many considerations to be discussed and taken into account, the most important being the productivity of the machine and the maintenance cost and downtime to be expected with the new equipment. Productivity of a given mining machine is evaluated by the Industrial Engineering Department: analysis of potential upkeep and downtime calls for the Maintenance Department to enter into the task of evaluating new mining machines. This is a very important function of the maintenance department because a wrong decision or mistake in judgment, particularly in a commercial mining company, can be exceedingly expensive. Once the type and size of a machine is decided, an examination of units fitting the basic requirements will sometimes show one particular machine which has a distinct edge on the competitive machine. In this case, the decision is easy. However, in most cases, the performances of the machines being considered are so close that the decision becomes one that is very difficult to make on performance alone. Serious consideration must then be given to maintenance performances and features of the machine which would permit lower maintenance and less downtime.

Jan 7, 1963

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By Arnold Hoffman

A RESPONSIBLE steel executive recently declared that scrap shortages, despite fantastic prices reaching up to $50 per ton, are responsible for the loss of 140,000 tons of steel a month and that in March 1947 alone 25 more steel furnaces could have been operating were it not for scrap scarcities. His answer to this serious situation was to ask for a speedier flow of scrap and also abolition of Government control over pig iron distribution. It would be more logical, perhaps, if an answer to this growing problem of scrap deficiency were sought within the steel industry itself. As long ago as 1933, L. B. Lindemuth, a consulting steel metallurgist, warned the steel industry that a shortage of scrap was inevitable and that beyond 1938, adequate supplies for open-hearth furnaces could not be expected. The outbreak of war, with consequent phenomenal demands on the industry, accelerated production of steel and further worsened the scrap situation. Today we are suffering from a condition which could have been prevented had the industry been more far-seeing and provided for an inevitable contingency. However, better late than never, and measures can now be taken to alleviate permanently scrap shortages in the future. This can be done by greater utilization of heavy sinter which experience proved is an excellent substitute for scrao and lump ore.

Jan 1, 1947

By W. H. McCormick, H. J. Benecki

CONSIDERING that a typical modern drilling machine strikes approximately 2000 blows per min and may develop a force of 30 to 200 ft-lb, de- pending upon size of the drill used, the importance of uniform stress distribution in this type of drilling becomes obvious. If the rod were perfectly symmetrical, and if it did not rotate, the problem would be relatively simple, however, the necessary forging, machining and heat treating operations prevent attaining this state of perfection. Take the modern hollow drill rod. The blow is transmitted not from the striking end of the rod directly through to the point of impact of the bit in the rock, but rather through a somewhat complex tool. To add further problems, this entire assembly is rotated immediately after the impacting blow. Rather than attempt to discuss the magnitude and distribution of stresses, it is desired to present a few things that will minimize unusual stress concentration and produce a rod in which the stress distribution will approach the theoretical ideal.

Jan 3, 1954

By NEWTON B. KNOX

IN Bolivia, mining is still the principal economic activity, as it was before and during the Spanish Colonial period. Tin, tungsten, antimony, copper, lead, zinc, gold, silver, sulphur, and a little bismuth are produced. The Andes mountains are divided into two main ranges in Bolivia; the Western range marks the border with Chile and the Eastern range forms the backbone of the country; in the North it drops rather abruptly eastward, to the plains of the Beni, whereas in the South it splits and is separated from the Chaco flatlands by a series of folded mountain ranges. In general the mineral deposits are found within the Eastern range or in the hills that rise from the high plateau between the ranges - really parts of the Eastern range partly submerged by recent sediments. The mineral belt is thus over 500 miles long and about 100 miles wide and includes most of the principal centers of population and the most important means of communication. The region is mountainous and the roads are bad; furthermore labor is a serious problem, for the land is poor and the agricultural population is never far from hunger. The floating supply of miners is limited and soon exhausted in any emergency like the present.

Jan 1, 1945

Established as a Division December 15, 1948 Clayton G Ball, Chairman Louis C Raymond, Vice-Chairman Sheldon P Wimpfen, Vice-Chairman Henry T Mudd, Vice-Chairman A H Lindley, Jr, Secretary-Treasurer Division of Foreign Activities U S Bureau of Mines Washington, D C

Jan 1, 1956

Executive ERLE V. DAVELER. Chair u W. B. HEROY PAUL D. MERICA JOHN M. LOVEJOY WILLIAM WRAITH Finance H. G. MOULTON, Chairman H. T. HAMILTON HENRY KRUMB Admissions JOHN L. CHRISTIE, Chairman GEORGE D. BARRON, Vice-Chairman FRED H. KAY PHILIP KRAFT H. Y. WALKER

Jan 1, 1938

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

By Norman Yarborough

Much has been written about the energy fuels including their standing with respect to reserves, their delivered Btu costs, their potential in the electrical generating market and their capabilities to meet a burgeoning demand. Yet, when all factors are placed in their proper perspective, the spiraling electrical energy market alone should guarantee each fuel a better than average market for the foreseeable future. In fact, a study made by the U.S. Federal Power Commission on the spare capacity utilities have on hand indicated that 39 of the 181 major utility systems had less than 10% reserves on hand at the end of 1969. Fuel supplies are critically low in some areas, especially in the Southeast, South Central and Midwest areas of the U.S. In other systems equipment shortages resulting from faulty equipment or delays in getting new equipment deliveries causes power failures during peak loads. In addition, lack of labor curtails the erection of some new facilities and prevents many other facilities from operating at capacity.

Jan 1, 1970

Open pit operators have found the dropball crane a great aid in cutting costs and hazards of secondary breakage. But a common problem in using the unit has been with the shock absorbing connection from the cable to the dropball itself. Blair Limestone Div. of Jones & Laughlin Steel Corp. has come up with a new connector to solve this problem and to save the time usually lost in frequent replacement of the cable slings, chains, or old tires hitherto used at this point. J&L personnel solved the problem by combining three ideas from other dropball crane owners. Their unit consists of two long U-bolts running through a heavy spring originally made for use on a vibrating screen. Heavy duty swivels attached to the bent ends of the U-bolts provide attachment points for the crane cable and the special chain to the dropball. Connection at the dropball is by an eyelet welded directly into the mass of steel, and a special alloy chain is connected to this with a clevis.

Nov 1, 1955

By Guy Crane

I. INTRODUCTION THE geology of the Tintic mining district, fully treated, would occupy an elaborate monograph. This less comprehensive paper is devoted primarily to the occurrence and origin of the orebodies of the district, while space is given to those phases of the general geology only which seem necessary to a proper setting of such a discussion. The first geological report on the Tintic district to be issued was that by Tower and Smith, published in 1899, in the form of a paper in Part III of the Nineteenth Annual Report of the U. S. Geological Survey, and also as Folio No. 65, Geologic Atlas of the United States. About four years ago a second investigation was begun by Waldemar Lindgren and G. F. Loughlin, of the U. S. Geological Survey. With the exception of a paper on the oxidized zinc ores of the Tintic district by Mr. Loughlin, the results of their work are still unpublished. The writer's acquaintance with the district began in the fall, of 1913, and has extended over a period of about two years.

Jan 10, 1915

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

Polluted air and water, despoiled land and excessive noise are the unwelcome results of the population growth and a rising standard of living. The consumption of goods and services, including metal products and minerals, by all people is increasing so rapidly that civilization is in danger of destroying the environment in which it lives. This is true because every human activity affects the environment, whether it is air, water or land. While E. F. Osborn, director, U.S. Bureau of Mines, says . . . "some members of the mineral industry are reluctant to recognize environmental demands" . . . William T. Pecora Under Secretary of the U.S. Department of the Interior.. . says that, "to maintain levels of resource development and environmental quality needed to satisfy our affluence, we must trade off values rather than turn off troublesome operations." What it seems to boil down to is how much control of its operations is the mineral industry willing to accept-internal policing or strict government control? The answer lies in how well the mineral industry maintains a balance between mineral development and environmental quality.

Jan 1, 1971

By Eugene Guccione

FOREWORD-In an interview published in the May 1975 issue of MINING ENGINEERING, one of the world's most respected scientists, nuclear physicist Hans Bethe discussed the reliability of nuclear power plants and their unmatched safety record. The Nobel laureate also refuted the anti-nuclear lobby's claims that nuclear plants emit harmful radioactive effluents. When asked whether the US has sufficient uranium resources, Dr. Bethe replied that "it depends on the time of introduction of the commercial and advanced breeder reactors which, in effect, can generate more nuclear fuel than they consume." The United States has enough U3O8 to last until the breeders can take over in 1995, said Dr. Bethe. But lie warned that extensive environmental damage would be caused if "environmentalists" succeed in delaying the development of the breeder. Any such delays, he noted, would vastly increase the demand for U3O8 in conventional reactors; this, in turn, would impose an immense burden on the US uranium mining industry, which would then have no alternative but to mine the low-grade Chattanooga deposits.

Jan 4, 1977

By William B. Plank

Mineral engineering student enrollment in U. S. and Canadian schools for 1955-1956 is 11,408, an increase of 11 pct more than last year. The undergraduate and graduate engineering students in both countries number 251,765, or 13 pct more than last year. These figures have been released by the American Society for Engineering Education. The largest increase in the undergraduate mineral engineering group in the U. S. is in ceramic engineering, with 676 students, or 31 pct more than last year. The next largest increase is in mining which shows a gain of 13.5 pct, compared with a gain of 13.1 pct in the total undergraduate enrollment in all engineering schools approved by the Engineers' Council for Professional Development. This figure is 190,355, which approaches the prewar figure. Metallurgical undergraduates increased 13 pct; geological, 5 pct; and petroleum, 2.5 pct. This year the figures for geophysics are combined with those for geological engineering, making a total of 1610 undergraduates, of which the geophysicists comprise about one seventh.

Apr 1, 1956