Search Documents

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 1, 1950

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By HUBERT O. De

IN December, 1936, several drilling tests were made at the Hubert O. De Beck feldspar mine at Green Mountain, N. C., to determine the most efficient type of hammier-drill bit and drilling method for use at this particular property. This mine is well recognized as having the hardest rock in the Burnsville - Spruce Pine feldspar district and drilling costs always have been high. Local structural deformation has greatly distorted and warped the normal crystalline structure of the feldspar so the rock is much tougher than usual. In studying drilling methods and bit types, available literature was re¬viewed but little specific data could be found on the direct comparison of four-point and six-point drill bits so the following results may be of some interest.

Jan 1, 1937

By Rixford A. Beals

It has been observed with considerable accuracy that if the major U. S. mines were moved to Mexico tomorrow, many of them would be losing money. But the companies would continue to operate, losses or not, because they would have to. And some of the newest and most promising low grade ore projects in the U. S. would never have "gotten off the ground" had they faced the equivalent of the mining taxes now in effect in Mexico. No one of the various mining taxes in Mexico seems prohibitive by itself. Taken together, on the balance sheet, however, the picture changes. Production and export taxes alone take from 20 to 40 pct of the gross product value for base and precious metals.

Jan 2, 1955

By Edwin T. Wood

THE term blending as used herein refers to the mixing of ores assaying more than 0.20 pct U3O8 with low grade material assaying less than 0.20 pct U3O8. Such blending when properly understood and controlled will produce more total dollars of profit from many mining ventures. The question whether or not to blend is particularly vexing when an orebody is surrounded by an envelope of low grade material or separate tonnages of low grade exist which could be extracted coincident with the higher grade ores. Should any, all or part of this low grade be mined? If so, in what proportion and what is the limiting assay of the low grade material?

Jan 7, 1958

By Sven A. Wehrwein

Leveraged buyouts are a fixture in today&apos;s market place. This paper will include comments on how LBO&apos;s are analyzed, structured and sold, as well as an overview on the present environment of LBO&apos;s.

Jan 1, 1990

By I. E. Rosenzweig

GEOPHYSICAL prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" II and 12. The current of intensity J, supplied by this battery, passes through the earth between these elec- FIG. 1.-GENERAL ARRANGEMENT OF APPARATUS. trodes. A potential difference U will be measured between two other electrodes V1 and V2, called "potential electrodes." According to the configuration of electrodes (Fig. 1), the resistivity of a homogeneous soil results from the formula p = 2pcaU/J [1] where c=1/a/b11 - a/b12 ? (a/b21-a/b22) [2]

Jan 1, 1938

By Edward Keller

Jan 1, 1906

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35&apos; and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption &apos;1 The Land&apos;s End of Two Worlds."

Sep 1, 1907

By Fuller, T. S.

THE number of rare or uncommon elements in use in the electrical industry nowadays is large, their application having come about through investigational work in industrial search laboratories and &apos; educational institutions. Such elements, together with those whose properties are more generally known, constitute Nature&apos;s gift to mankind and make possible the intricate devices which further our modern civilization. The&apos; quality of raiaity is one of degree, and obviously depends largely on one&apos;s point of view. From the standpoint of quantity measured in the customary units of weight and volume, the amounts of many of the elements required are extremely small, but from the of view of performing some particular function or .other in a manner more satisfactory or cheaply than can be accomplished by any other sub- stance, the use in question may be extremely important.

Jan 1, 1928

By R. F. Hehemann, Darrell W. Smith

The kinetics of alloying- in W-5 rot pct Re powder compacts were investigated at temperature about the upper limit for the formation of the x phase, such that a single intermediate phase was involved in the process. The rates and directions of motion of the a-o and o-b interface were assessed as functions of tinze at the sintering teri7peraticve by quantitative izetallog-ralhic techtziques. The iiotion 01 these interjuces could be specified approxitnate1.y by u Parabolic )-ate law and deviations from this ,rate law were attribuled to a complex interaction between surface dif&apos;fusion and volume diffusion during the initial stages of sintering. WHEN binary or more complex alloys are produced by sintering compacted blends of elemental powders, a complication is encountered which does not arise in the sintering of pure metals. In addition to concern for grain size and densification, the rate of inter diffusion of the component elements must be considered. The general problem of alloying during sintering has been treated by numerous investigators.&apos;-7 These investigations have been concerned only with systems that form continuous series of solid solutions and a concentric-sphere diffusion model4 provides a useful description of homogenization in these stems.&apos; Some controversy remains, however, over the contribution of surface and grain boundary diffusion to the homogenization process. Heckel% ePorts that homogenization can be described by volume diffusion at all temperatures, whereas other invetiators&apos;&apos; recognize the importance of surface and grain boundary diffusion, particularly at lower temperatures. Analysis of the homogenization process in partially miscible systems is complicated by the motion of the interfaces separating the individual phases. A simple analytical solution does not exist for such finite systems with spherical symmetry. It was the purpose of this work to examine the kinetics of the formation and dissolution of an intermediate phase in a binary system through an assessment of the motion of the interfaces separating this phase from the terminal solid solutions. PROCEDURE The W-Re system is an example of a partially miscible binary system and was selected for study because of its current importance in refractory-metal technology. The equilibrium phase diagram, Fig. 1, shows that the o phase will be formed by interdiffu-sion between tungsten and rhenium. At temperatures between approximately 2125" and 282O°C, the o phase will appear as the only intermediate phase in the diffusion system. In this work, a mixture of elemental powders containing 5 pct Re was employed. In such a mixture, the rhenium particles will be distributed randomly in a tungsten matrix. During sintering, a o-phase layer will form at the W-Re interface. The development and subsequent disappearance of the o phase are controlled by the relative rates and directions of motion of the 0-0 and a-p interfaces. The motion of these interfaces can be inferred from quantitative metallographic measurements of the average radii of the o shells surrounding rhenium particles. Elemental tungsten and rhenium powders of commercial purity were employed in these investigations. The rhenium powder was spheroidized from +200 mesh agglomerates by plasma-arc spraying and was then classified to yield a powder composed of essentially

Jan 1, 1967

By R. H. Tien

Temperature distribution as well as position of the solidified front is solved by means of "heat balance integral", for the case of freezing a slab with time-dependent surface temperature. Numerical solutions for the cases of linear variation and exponential decay for surface temperature are given. Application also includes solidification of casting. An increased interest in the heat-transfer problem involving a change of phase has been developed in recent years. Practical problems include solidification of a casting, freezing and thawing of soil, ice formation, and others. Despite the importance of the topic, a literature search reveals relatively few solutions which may be extended to practical problems. Due to mathematical complexity, which comes from the nonlinearity of governing differential equations, exact analytical solutions which have been published are limited to a few cases with simple boundary conditions. Although numerical solutions of these problems have become available after highspeed digital computers were introduced, lack of simple and general methods of programming for computation makes this approach impractical. The case of the semi-infinite slab with constant surface temperature was solved in the 19th century. In honor of Neumann, who first found an analytical solution, this kind of problem is generally referred to as the Neumann solution. As has been shown in Fig. 1, the problem to be analyzed is the freezing of a semi-infinite region (x > 0) which is initially liquid at the melting temperature with the surface (x = 0) maintained at time-dependent temperature. This analysis can be applied to the study of many casting processes where most of the heat removal is essentially unidirectional. "Heat balance integral" which has been used by Goodman1 is employed in this analysis. The concept of "heat balance integral" is to define a quantity, d(t), called the thermal layer. Beyond this thermal layer, for all practical purposes, there is no heat transfer, and the region is at the equilibrium temperature. "Heat balance integral" is obtained by integrating the conduction equation with respect to the space variable over this thermal layer d(t). Choosing some plausible temperature distribution, usually a polynomial or a finite trigonometric series in the space variable, this integral equation becomes an ordinary differential equation, with time as the independent variable, which can be solved by classical methods. The thermal layer and "heat balance integral" are equivalent, respectively, to the boundary-layer thickness and the momentum integral in hydrodynamics. A modern account of Prandtl&apos;s concept of the boundary layer and von Karman&apos;s momentum integral may be found in Ref. 2. Although the problem considered here has been limited initially to uniform melting temperature, the present method is equally applicable to the case with arbitrary temperature distribution in the liquid. STATEMENT OF THE PROBLEM The physical situation and coordinate system used in the problem to be analyzed are shown in Fig. 1. Notations used are listed in the table of nomenclature. Let us assume a semi-infinite region extending over positive x, initially at the uniform melting temperature. At the surface x = 0, a time-dependent temperature, which has a numerical value

Jan 1, 1965

By William P. Blake

A recent paper by Prof. George P. Merrill, Curator of the Department of Geology of the U. S. National Museum, Wash-

Jan 1, 1897

Jan 1, 1884

By Bobby P. Faulkner

The Tennessee Copper Co.&apos;s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By L. F. Reinartz

FROM the earliest times when our prehistoric ancestors laboriously fashioned crude tools and weapons from meteoric iron until our day when we manufacture steel in 150-ton open-hearth furnaces, the production of iron and steel has played a dramatic and important role in the development of civilization. Progress in the science of refining iron ore into iron and steel was painfully slow for many centuries. The keen scimitars of Damascus, the broadswords of the English knights, the coats of mail of French knights, and the Iron Pillar of Delhi are well¬known examples of medieval metallurgical technique. Expense and the scarcity of raw materials originally limited the distribution of iron and steel products. It was not until the nineteenth century that a determined effort was made to adapt the use of steel to peaceful pursuits. The spectacular and rapid strides made in the manufacture of steel during the last hundred years were hastened by the invention during the decade 1860 to 1870 of two great steelmaking processes-the Bessemer and the open-hearth process.

Jan 1, 1936

By Mark L. Requa

(San Francisco fleeting, October, 1911.) DURING the past two years California has developed a new and important oil-field : I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing save a great crater-like opening marks its location. The pipe is entirely worn away and gone ; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no, other wells in that field or elsewhere throughout the State that in any way compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to show evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small increase, when balances are struck off. The increase of new area has come from extensions of the Midway field, the development of a field in Lost Hills and Belridge, and extensions of the Fullerton-Whittier field in southern California. In these later developments, down to date, the fresh area absolutely proved is not much in excess of 3,000 acres. Recent developments in Coalinga indicate the possible extension of that field to the south, but at great depth. Coalinga is still the most northerly field of any consequence in the State. The Kettleman Hills have hitherto brought in nothing, although a

Apr 1, 1912