Search Documents

By Norman Ketzlach

Manganese Products, Inc. has developed a chemical process for the recovery of high-grade manganese oxides from low-grade manganese ores. Ammonium sulphate is also produced. Manganese ore is leached with sulphurous-sulphuric acids. The impurities are removed with ammonia, heat, and air. Manganese oxides are produced by addition of more ammonia and air under pressure. Ammonium sulphate is recovered from the remaining solution.

Jan 3, 1950

By T. T. Read

JAPAN'S iron and steel industry has always been closely connected with military strategy. Many years ago it became evident that the country's iron-ore resources were too small to support any extensive industry. As a result a belief in the imperative necessity of securing such resources has influenced Japan's political and economic policy in the Far East. Iron-ore developments in China are too well known to need repeating except to note that they have been rather unsatisfactory to both China and Japan. The ore deposit at Tayeh, in China, is not as large as was first believed and, though that and other sources of supply in China proper are now furnishing Japan a little more than a million tons of ore yearly, it cannot be counted upon as a large permanent source of supply. The deposit in Shantung proved so disappointing on further exploration that operations there have, so far as I know, long since ended. The operations at Pen-bsi-hu, in South Manchuria, which C. F. Wang de¬scribed in the A.I.M.E. TRANSACTIONS for 1918, Vol. 59, were reported to have yielded 84,000 tons of pig iron in 1928 and about 50,000 in 1935, so they seem to be going back.

Jan 1, 1937

By William F. List, Marvin A. Schuster

Monolithic electrooptical mosaics of 2500 photo-transistor elements with internal row and surface column interconnections have been fabricated by epitaxial-planar diffsion techniques. Unique access to any elemed of the mosaic is provided through one of the fifty X and one of the fifty Y external leads. The sensor mosaic can be used for imaging applications and has a 1:1 aspect ratio, a resolution of 100 lines per in., a dynamic range in excess of lo3, a sensitivity of 0.5 per pw, element response within a 2:l range over 75 pct of the mosaic, and a minimum detectable signal of the order of 10-' w. Design considerations which ilnpose particclar fabrication yequirements are disctussed along with some of the problems peculiar to the epitaxial and planar-dijfision techniqes by which this device is fabricated. The solid-state silicon monolith has an imaging area of 0.5 by 0.5 in. and an element center -to- center spacing of 0.010 in. J monolithic solid-state electrooptical device has been developed as the photon-sensing mosaic for use in an image-converter system.' This system is the solid-state equivalent of the vidicon and can image radiation in the visible and near-infrared regions of the spectrum. The electrooptical image converter has the desirable size, weight, reliability, and low-power characteristics inherent in solid-state devices. It is read out by direct-wire means rather than by beam-scan techniques. The packaged unit is shown in Fig. 1. A selection of material for the sensor was based on considerations of both reliable fabrication techniques and material spectral response. Silicon was selected both for its response from the lower end of :he visible to the long-wavelength cut-off above 11,000A and for its well-developed epitaxial planar-diffused technology. The electrical image is composed of M x N discrete information bits with each bit emanating from one of the individual phototransistor sensors. The interconnected mosaic concept was introduced to provide a structure which is both manageable in its number of leads and compatible with conventional viewing systems which accept XY data. Interconnections along the Y direction are provided by internally diffused strips, while interconnections along the X direction are formed by vacuum-deposited metal surface bars. Unique access to any individual element of the M x N mosaic is available through one of the M and one of the N external leads. PHOTOTRANSISTOR DESIGN A phototransistor structure2 was selected for the discrete photon detectors of which the mosaic is com- posed. Basically, the mode of phototransistor operation is such that incident quanta are absorbed in the base area of the element where they generate electron-hole pairs. If the electrons are liberated within a diffusion length of the depletion region around the collector junction, they will diffuse to this depletion region and be swept across the junction where they account for a small component of the photocurrent. Similarly, the holes which are created within a diffusion length of the emitter junction will diffuse to this region where they forward bias the emitter and so induce injection of minority carriers into the base. This accounts for the substantial transistor photocurrent. This mechanism of operation implies several design and fabrication goals for the individual sensor elements: high electrooptical conversion efficiency, sufficient carrier lifetime in the base regions, and a maximum volume in which photons can be absorbed within a diffusion length from the depletion layer about the junction. Moderately high transistor gain is desirable to permit readout at low light levels; however, very high gain has a deleterious effect on mosaic dynamic range. The mosaic must also be characterized by good uniformity of element response as well as by good isolation between elements. The above set of conditions imply that junction depths must be optimized with respect to photon ab-

Jan 1, 1967

By John Hays Hammond

This is an era of " expansion; and, conformably with the change in commercial conditions, the function of the mining engineer, as well as that of his confreres in many other professions, has also expanded. From the position of an engineer, limited to the determination of technical questions, the engineer of to-day has come to assume an economic importance in those branches of industry dependent upon engineering skill for their development. He is indeed an engineer of limited usefulness who does not go further professionally than to submit a purely technical report on subjects presented for his consideration. While he has the same responsibility as formerly in the solution of the technical problems involved, he is further expected to supplement his report with advice on the financial and commercial aspects of these problems. For the great majority of problems presented to the engineer ultimately involve the determination of the pecuniary, relations of the propositions under consideration. The great corporation lawyer no longer earns his fee by merely submitting his opinion as to the legal issues involved in law-suits affecting the corporation; he now assumes charge of the entire legal work, including both the organization of the corporation and the maintenance of its legal status thereafter. In like manner, the engineer, whose report was, as I have said, formerly confined to the determination of the geological and other cognate features of a mining enterprise, is now expected, not. only to embody information on these subjects in his report, but also to give his opinion whether the property offered for sale in pursuance of such an enterprise is worth the price asked for it. Moreover, if he recommends the purchase of a property, he incurs a certain moral responsibility for its efficient manage-

Nov 1, 1908

?Aaronson, Alfred E , Oil Producer, Pres, Tuloma Oil Co Tulsa, Okla '18 ||Abad, Leopoldo F , College of Mm , Univ of California Berkeley, Cal '23 ||Abadilla, Quirico A , Geol Dept, Cia Mexicana de Petroleo "El Agmla," S A , Edifico "El Aguila," Esq, Caller Aurora y Comercio, Tampico, Tamps , Mexico '20 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, O '21 Abbott, Clarence E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Student, Univ of Arizona Tucson, Ariz '23 Abe, Asaka Ashiya, Mukogun, Hmyogoken, Japan '14 Abeel, George H, Jr , Cons Min Engr 4612 W 17th St , Los Angeles, Cal '18 Abel, Albert E , Asst to Pres , Valley Mould & Iron Corpn Sharpsville, Pa '19 ?Abeloff, Miran S 322 W 45th St, Ness York, N Y '21

Jan 1, 1923

?AARONSON, ALFRED E , Vice-Pres , Mid-Co Petroleum Co, Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr Address wanted '76 || ABADILLA, QUIRICO A, Geol Dept, Cia Mexicana de Petroleo "El Aguila," S A, Edifico "El Aguila," Esq, Calles Aurora y Comercio, Tampico, Tamaulipas, Mexico '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 ABBOTT, LOUIS BENJAMIN, Chief Engr, Consolidation Coal Co, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met Engr, Peerless Motor Car Co, Cleveland, Ohio '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 635 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Asst to Pres, Valley Mould & Iron Corpn, Sharpsville, Pea '19 ABEL, W D, Min Engr Forum Bldg, Sacramento, Cal '19 ABELL, O J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY G E Willow Springs, Mo '20

Jan 1, 1923

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

The following list comprises the names of those persons who became members during the period of Mar. 10, 1918, to Apr. 10, 1918. ADAMS, NOAH- :.. Geol.,. E. N. Gillespie & Co., Box 1875, Tulsa, Okla. ALVAREZ, PEDRO Asst. Met., American Smelt. & Refin. Co., Blue Hill, Maine. BARTRAM, JOHN G., Pet. Geol., Roxana Petroleum Co. of Oklahoma, Cheyenne, Wyo. CHANEY, S. E Supt.., Arizona Binghamton Copper Co., Stoddard, Ariz. CLEVELAND, EARL C Mgr., Deadwood Min. Co., Mogollon, N. M. DENNIS, HOWARD B Min. Engr., Empire Mines, Grass Valley, Cal. FOWLER, ARTHUR A., Partner, Rogers, Brown &- Co., 30 Church St., New York, N. Y. FRIEDMAN, L. A Pres. and Gen'l Mgr., Rochester Mines Co., Lovelock, Nev. GUIBERSON, S. ALLEN, JR 923-24 1. N. Van Nuys Bldg., Los Angeles, Cal. KROHN, ARTHUR Mine Supt., Missouri Metal Corpn., Mine La Motte, Mo. KURSELL, H. A., Mgr., Altai Mines Ltd., Zmeinogorsk, Altai Gov't, Siberia, Russia. LANE, L. RAY Mine Examinations, Galiano 24, Aptd. 1066, Havana, Cuba.

Jan 5, 1918

By Clyde E. Williams, JAMES L. GREGG

THIS review of the past year's progress in iron and steel metallurgy presents examples of only a few of the interesting or important accomplishments made in the United States. In the field of iron ore concentration increased attention was given to the study of the more difficultly separated wash ores and some progress was made in tabling. One difficulty with the table, in concentrating iron ore where the percentage of concentrate in the feed is large, has been the removal of fine silica from the thick layer .of concentrates in the cleaning zone. One company has -Made an important contribution toward the solution of this problem by an extension of the well-known plateau principle. By a special riffling of the plateau section of the table, the concentrates are crowded together. This action forces the fine silica to the top of the bed in the cleaning zone, whence the cross-flowing currents of water -can wash it into the middling product. Some work has been done on the application of froth flotation to the concentration of iron ores. Laboratory experiments were made at the Colorado School of Mines in which hematite was, successfully floated. Using oleic acid as a frothing and collecting agent and sodium carbonate as the conditioning agent, a high recovery of rich ,concentrate was obtained. A laboratory flotation unit is in use at Taconite, on the Mesabi range, and a commer-

Jan 1, 1932

By Luther Lennox

DURING the last few years, one of the great problems in the milling of all ores has been that of crushing. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of crushing to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of crushing methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative crushing resistances of a number of ores now being milled in this country and Alaska, the management of the Portland mills requested samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh . screen; in the screen analyses tabulated and plotted herewith, the 150 mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves.

Jan 8, 1918

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, LOUIS K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt , Mazapel Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexico '23 Abbott, Clarence E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div 'Jenkins, Ky '15 Abbott, Robert R , Met Engr, Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 ?Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburgh, Kans '20 Abey, Hiroshi, Min & Met Engr, Takata & Co, 2 Yeirakucho, Nechome, Kojimachi-ku,

Jan 1, 1923

By P. de Vitry, Oliver Bowles

The conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 93/16 or 54 in. The equipment, methods used, and accomplishments have been described in previous reports.'-I Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible to maintain in stock marbles of the color, size, and thickness called for, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill such orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By P. de Vitry, Oliver Bowles

The conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 93/16 or 54 in. The equipment, methods used, and accomplishments have been described in previous reports.'-I Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible to maintain in stock marbles of the color, size, and thickness called for, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill such orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By KENNETH CITTISGHAM

During the year 1945, the total number of wells drilled in Ohio, including the. non¬productive wells, was 1034. For the 10-year period ending with 1945, the average completions per year were 1125, the least number being 910 in 1938, and the maximum 1561 in 1941. The proportion of dry holes in 1945 was 37 per cent?about the same as for the year 1944 but exceeding the 10-year average, which was 34 per cent. The number of oil wells completed exceeded the number drilled in 1944 by about 30 per cent, the average initial per well being the same in both years. Gas-well completions were approximately 10 per Cent less than in 1944, with the average initial per well about 5 per cent greater. The difference in number of oil and gas wells in the two years was in Berea and Clinton completions, as the number of oil wells increased about 30 per cent, owing to greater activity in the two sands named, while the number of gas wells decreased because of fewer completions therein.

Jan 1, 1946

Jan 1, 1882

By J. L. Schroeder, W. G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard. In the Gary district, West Virginia, two of the five operating mines have areas known to be vulnerable to mountain bumps.These are the No. 2 and 6 mines, which are working the Pocahontas No. 4 coal seam. In this area the seam is overlain at a zero to 10-ft interval by the massive Eckman sandstone, which is about 100 ft thick in the vulnerable areas. Total overburden, consisting of shale, coal seams, and sandstones, ranges from 700 to 1400 ft where bumps have occurred (Fig. 1). The coal seam is 4 to 8 ft thick and has a weak columnar structure of very soft and spongy or woody coal. The immediate top is either the Eckman sandstone or hard shale, both of which provide generally good roof conditions for mining operations. The bottom ranges from medium to hard gray shale. The incidence of bumps in the Gary district dates from about 1930 and can be correlated to some degree with the increased rate of extraction attained with mechanical mining. During early years of operation at the No. 2 and 6 mines, most of the work was development and under comparatively light cover. As overburden became heavier, together with an increasing percentage of coal coming from pillar extraction, mountain bumps began to occur. Before 1945 they were much less severe than in later years, and because there were no injuries or fatalities, no records were kept. But by 1951 the incidence of bumps had increased to such extent that it became evident a mining system would have to be designed to eliminate or at least minimize these occurrences. Drawing on experience with modified versions of old systems and certain characteristics peculiar to the Pocahontas No. 4 coal seam, the district mining engineer, Martin Hayduk, outlined the essential factors for bump control in the Gary district. These control factors indicated: 1) The highly stressed area, which lies within the limits of convergence effects, moves at approximately the same rate as the retreating pillar line. 2) There is a decided softening of the periphery of blocks which is greatest and deepest on the gob side. 3) Blocks less than 45 ft wide never have been known to bump in the Pocahontas seams. Fig. 2 shows the mining plan based on these observations—a thin-pillar system with a minimum of secondary development. It was recognized from the start that the Hayduk system had certain limitations. When pillar work backed up to an inevitable surrounded block it was no longer applicable; also, burnt bottom and/or unknown factors reduced the system's effectiveness in certain headings. Since there was no way to eliminate the loaded block, it was decided to experiment with auger drilling to attain controlled release of this stored-up energy. The decision to auger was made after consideration of three separate plants, which were: 1) To cut the solid block into pillars of maximum size by driving away from the fracture line and at such a distance outby that development

Jan 1, 1959

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925