Search Documents

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By Leonard A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region com- prises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1 ). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County.

Jan 10, 1959

By John G. Tate, George W. Nicolson, James L. Bruce

For more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.' From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. Description of Ore Bodies The shape Of the Ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions) extending from unknown depths below the bottom level at elevation 250 ft below sea level) to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the Ore body extended to surface and was Mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the Ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upper-side of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and Clay sedimentaries of Miocene and later age, The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-Stained by the descending meteoric waters, It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pet Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pet. on the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main Ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. 'This probably can

Jan 1, 1949

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By C. H. Mathewson

(New York Meeting, February, 1916) DURING the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform conditions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,1 in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent. reduction of area by rolling

Jan 1, 1916

By Burk, Hugh A.

AT THE inception of the cyanide process and its adaptation to the practice of gold and silver metallurgy much difficulty was experienced in applying it to auro-cupriferous ores, both in economy of treatment and recovery of the gold from solution. The presence of copper in the ore effected a high chemical consumption of cyanide during treatment, and in the solvent solution, it retarded the precipitation of the gold on zinc shavings. The coating of the copper on the zinc shavings presented even worse difficulties than the increased cyanide consumption as most ores contain a small amount of copper. This interference of copper led to the use of other precipitating methods and attempts to recover the cyanide which was consumed during ore treatment. Of the other methods used, electrolytic precipitation was the most practical until a better understanding of the application of zinc shavings and zinc dust developed. In September, 1905, a patent entitled, "Method for Recovering Precious Metals from Solution," was granted to Isaac Anderson and Michael Scanton. This method is adaptable to precious metal ores containing a small percentage of copper but has never been extensively used or perfected. The process has

Jan 1, 1925

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By A. M. Gaudin

A great number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,² involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By Armando M. Lago

Secular and cyclical patterns of postwar sources and uses of funds of the mineral sector are analyzed. A simultaneous equation behavior model of sources and uses of funds is developed for both mining firms and integrated producers, and these models were put through the task of predicting the financial and expenditure be-havior of mineral corporations in response to mergers and changes in investment tax credits and depletion allowances. Finally, the quantitative analysis methodology is applied to the analysis of optimum capital structure of mining corporations. The postwar changes that have occurred in the expenditure and financial behavior of mineral corporations are reviewed, particularly the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail. An econometric model of mineral corporate financial behavior is formulated. This model is then estimated and reviewed. Policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector are discussed. Finally, the optimum financial structure of mining firms is discussed and the effect of corporate financial structure on the mining corporations' average cost of capital is analyzed.

Jan 1, 1971

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By D. Bergekoff

IN the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By V. Jares

DESPITE the fact that a combination of metals-aluminum-zinc-tin, and sometimes aluminium-zinc-cadmium-is extensively used for aluminum solders, as well as for die-castings, the constitution of these alloys has not yet been made clear. I. BINARY SYSTEMS The system aluminium-zinc is the basis of the ternary alloys under consideration. Their composition was made sufficiently clear by the investigations of Roscnhein and Archbutt,1 Bauer and Vogel,2 Sander .and Meissner,3 Hanson and Gayler4 and Isihara.5 Only the temperature of decomposition of the crystals s seems still to be doubtful, whether it is considered as a compound of Al2Zn3 (according to Bauer and Vogel) or as an intermediate phase of variant composition (according to Hanson and Gayler). This temperature is given by most of the authors, as in the neighborhood of 256° C., only Isihara giving 280° C. As its accurate determination is of special importance in the study of the ternary alloys under consideration it was experimentally controlled in the following manner: An alloy corresponding in composition to the formula Al2Zn3 was made, in which the temperature effect was found to be the greatest. This was drilled and a silver-constantan thermoelement inserted into the cavity so as to be in direct contact with the alloy. The whole was then very slowly heated and the heating and cooling curves determined. The transition temperature from the heating curve was found to be 281° C., whereas-from the cooling curve it was 252° C.

Jan 10, 1926

Jan 4, 1951

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.? Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation ;2,3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942