Search Documents

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

Abadilla, Quirico A. Catanawan, Tayabas, P I '20 Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co, 50 Church St, New York, N. Y. '21 Abbott,-A. N., Mines Supt, Mazapil Copper Co., Ltd .. Concepcion del Oro, Zac., Mexico. '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn. Coal, Iron & R R Co. 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div . Jenkins, Ky. '15 Abeel, George H., Jr., Cons Min Engr... . Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin , Univ. of Pittsburgh Pittsburgh, Pa. '28 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kans '20 ||Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co . Scranton, Pa '27 Abey, Hiroshi, Min. & Met. Engr., Min. & Met. Dept, The Higher Technical School, Osaka, Japan. '17 Aborn, Robert H., Instructor in Met, Harvard University Cambridge, Mass. '19 Abozeid, Mahmood, Pet. Production Engr., Marland Oil Co Ponca City, Okla. '20 Abraham, Arthur W., Geol, Richfield Oil Co. Box 788, Bakeisfield, Cal. '20 Abraham, W. E. V., Member, Geol Staff of Burmah Oil Co, Ltd Nyaunghla. Upper Burma, India. '23

Jan 1, 1923

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Sherwin F. Kelly

GEOPHYSICS may be considered a vice (albeit, I submit, a comparatively harmless one) whose career is aptly described by Pope's lines: Vice is a monster of so frightful mien, As to be hated needs but to be seen; Yet too oft, familiar with her face, We first endure, then pity, then embrace. Although there may be some that have not yet succeeded in emancipating themselves from the first stage of horrified contemplation, geophysicists may be duly thankful that there are mining men and geologists that have arrived at a state of apparently irretrievable damnation.

Jan 1, 1936

By H. H. Stout

In the early fall of 1925, the writer was conducting, in the Ledoux and Co. laboratory, New York, experiments directed toward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various different gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500º to 1600ºF. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode particles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500ºF." Smoot's reaction, after a few moments considera- tion, was, "It looks perfectly all right to me.'' The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after conferring as to ways and means, decided to go ahead with preliminary laboratory experiments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: 1. Since brittle cathodes were often unintentionally produced, it seemed probable that the laws controlling this type of deposition could be ascertained. 2. We had already proved the gas-cleaning feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia University for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrouilded and heated by a resistance coil 01 Nichrome wire. Broken tough cathodes were used. Experimental Procedure The first run took place March 18, 1926. The resistance wire gave out when temperature of 1000ºF. was obtained. Pressure was immediately applied: perceptible ram movement stopped when 39,000 lb. per sq. in. on the copper was reached, with a maxi-

Jan 1, 1941

By Jay A. Carpenter

WAR?S impact on Nevada mining and rnetallugrcal operations has brought about a rapid rise in the gross value of the ores mined and milled for the atratezic metals, and a sharp decrease in that for the precious metals. The State?s total production over the present war years will averaged out 10 per cent above the good record of $39,000,000 in 1937. However. this annual production is low in contract to that of nearly $47,000,000 in 1877 in the days of the great bonanza on the Comstock, and that of nearly $49,000.000 in 1918 during the last World War..

Jan 1, 1944

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By J. D. Lubahn

Prior tests by Dorn, where the strain rate in a tensile test was suddenly changed, have shown a small, but definite rate-history effect to exist. If this effect is neglected in the calculation of creep behavior from tensile results, an error should occur. This paper shows that this error is smaller than experimental scattering, and may be neglected. DORN1 has found a small but definite rate-history effect in the aluminum alloy 250 at liquid-nitrogen temperature using tensile tests with an abrupt rate change. Such an effect is to be expected from pre-viously known2-6 temperature-history effects, together with general experience that effects produced by changing the strain rate a large amount are simi-

Jan 1, 1959

By ALFREDO INTZAUGARAT, MIGUEL BERRO

During the years 1943 through 1945, there was a decrease in the total oil production in Argentina. In the fields of Comodoro Rivadavia (Chubut Territory) and Mendoza and Salta Provinces, the production obtained was as shown in Table I. The only place where there was a small increase was Plaza Huincul, in the Neuquen Territory and Lunlunta, in the Mendoza Province.

Jan 1, 1946

By A. M. Gaudin

THE so-called Kick law' is generally accepted to . mean that for each reduction to one-half in particle diameter, in a unit weight, the same amount of work is required. In crushing-efficiency calculations on crushing tests it is customary, when basing the calculation on Kick's law, to assign ordinal numbers to each standard sieve size. These ordinal numbers increase by a constant difference with each successive sieve aperture, because standard sieve apertures are in constant ratio. Minus 200-mesh is generally assumed as equivalent to 37 microns in size. By definition, the ordinal number multiplied by the per cent material of any size is equal to the energy units in the material of that size in a unit weight of sample. The sum of all energy units is the energy units content of a unit weight of sample, whether it be crusher feed or product. The difference between the energy units in the product and that in the feed is the tangible result of the work input per unit weight of feed. From this the amount of work necessary for one energy unit may be calculated. This has been done for a quartz crushing-test made at the Intermountain Experiment Station of the U. S. Bureau of Mines at Salt Lake City, in which the net work going to crushing was carefully measured. The results of this crushing test are given in Table 1.'

Jan 1, 1929

IlAbad, Leopoldo F , Min Engr , Div of Mines, Bureau of Science, Manda, P I '23 ||Abadilla, Quince, A , Cia Minera de Petrolco El Aguila, S A Box 86, Puerto Mexico, Ver , Mexico '20 ||Abarquez, Ramon F , Met , Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt, Mazapil Copper Co , Ltd Concepcion del Oro, Zac , Mexico '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cle veland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H , Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abernathy, George Elmer, Prof Geol & Min , Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr, Takata & Co , 2 Yeirakucho, Nichome, ICojimachi-ku, - Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St , Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17 ?Abraham, Arthur W 1626 N Alexandria Ave, Los Angeles, Cal '21 Abrahams, Alexander I, Gen'l Mgr, Ricon Electrical Co Slough, London, England '13 ||Abrahamson, C Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson, Mill Supt, Utah Apex Min Co Bingham Canyon, Utah '21 Abrams, David H, Cons Min Engr 182 Worth St, Johnstown, Pa '20 ?Acker, E O'C , Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86

Jan 1, 1923

CONTENTS PAGE Simons, Theodore.-Basic Principles of Gravity Concentration-A Mathematical Study : :.. 1 Taggart, Arthur F. and Gaudin, A. M.-Surface Tension and Adsorption Phenomena in Flotation 11 Hersam, Ernest A.-Factors Controlling the Capacity of Rock Crushers 12 Shaw, S. F.-The Ore Deposits of Sierra Mojada, Coahuila, Mexico 12 Wilson, Philip D.-The British Columbia Batholith and Related Ore Deposits 26 Greensfelder, N. S.-Shot-firing by Electricity 27 Mitke, Chas. A.-Metal Mine Ventilation in the Southwest 28 Foley, F. B. and Howell, S. P.-Neumann Bands as Evidence of Action of Explosives upon Metals 30 Schwartz, H. A., Payne, H. R., Gorton, A. F., and Austin, M. M.-Conditions of Stable Equilibrium in Iron-carbon Alloys 30

Jan 12, 1922

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931

By L. G. Westgate

PART I.-AREAL GEOLOGY§ PIOCHE lies 240 mi. southwest of Salt Lake City, in southeastern Nevada, 19 in. west of the Nevada-Utah line. It is at the end of a branch line (33 m.), which connects at Caliente with the Los Angeles and Salt Lake division of the Union Pacific System. Its commercial relations are with Salt Lake City and Los Angeles, chiefly with the former. The surrounding area is part of the Great Basin, an arid region of alternating mountain range and intermont plain, the latter floored with outwash from the mountains. About Pioche the plain varies between 4700 and 6000 ft. above sea level. The town lies in a valley at the east base of a low northwest-southeast range (the Pioche Hills) 12 miles in length, which rises about 1000 ft. above the adjacent flat. West of the. Pioche Hills is a higher north-south range consisting of two parts: to the south the Highland Range, between Bennett Pass and Stampede Gap; to the north the Bristol Range, from Stampede Gap to Bristol Pass. This double range reaches altitudes of 8000 to 9000 ft., or more, (the highest point, Highland Peak, is 9395 ft.) and rises some 2500 ft. above the surrounding plain. It is continued in lower hills to north and south. Smaller ranges rise from the flat west of the Highland and Bristol ranges. The area studied and shown on the map (Fig. 1) is covered by 3 one inch to the-mile topographic sheets: the Highland Range, the. Bristol Range, and the Panaca, the latter mapped in part only. The sedimentary rocks of the district include Paleozoic limestones, sandstones and shales, Pliocene tuffs, and modern wash. Igneous rocks are represented by intrusive dikes and stocks and by extensive lava flows of mid-Tertiary time.

Jan 1, 1927

By Adolph Knopf, L. G. Westgate

Pioche lies 240 miles southwest of Salt Lake City, in southeastern Nevada, 19 miles west of the Nevada-Utah line. It is at the end of a branch line (33 miles), which connects at Caliente with the Los Angeles and Salt Lake division of the Union Pacific System. Its commercial relations are with Salt Lake City and Los Angeles, chiefly with the former. The surrounding area is part of the Great Basin, an arid region of alternating mountain range and intermont plain, the latter floored with out-wash from the mountains. About Pioche the plain varies between 4700 and 6000 ft. above sea level. The town lies in a valley at the east base of a low northwest-southeast range (the Pioche Hills) 12 miles in length, which rises about 1000 ft. above the adjacent flat. West of the Pioche Hills is a higher north-south range consisting of two parts: to the south the Highland Range, between Bennett Pass and Stampede Gap; to the north the Bristol Range, from Stampede Gap to Bristol Pass. This double range reaches altitudes of 8000 to 9000 ft., or more (the highest point, Highland Peak, is 9395 ft.), and rises some 2500 ft. above the surrounding plain It is continued in lower hills to north and south. Smaller ranges rise from the flat west of the Highland and Bristol ranges. The area studied and shown on the map (Fig. 1) is covered by three inch-to-the-mile topographic sheets: the Highland Range, the Bristol Range, and the Panaca, the latter mapped in part only. The sedimentary rocks of the district include Paleozoic limestones, sandstones and shales, Pliocene tuffs, and modern wash. Igneous rocks are represented by intrusive dikes and stocks and by extensive lava flows of mid-Tertiary time.

Jan 1, 1927

By B. D. Harden

FOR over fifty years the Spanish mine, 21 miles northeast of Nevada City, in Nevada County, California, has been one of the Bradley properties. Between 1883 and 1889 it was operated by the late Frederick W. Bradley and P. R. Bradley. The ore averaged only about $1 a ton at that time but the mine was credited with a production of about $900,000 in that period. The property was then closed down until 1922, when the Bradley interests reopened it and continued development for the next nine years, when a 50-ton mill was built. This began operation in April, 1931. This was a selective flotation plant, with the tailing treated on Wilfley tables, and operated on ore from the No. 4 and No. 16 tunnel stopes. This ran from $3 to $6 in gold, 2 to 3 oz. of silver, copper 0.6 per cent, lead 1.5,

Jan 1, 1935

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.' As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972