Search Documents

By M. L. Jeremic

Abstract-Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 4, 1978

By Vincent T. Ricca, Kurtis Chow

When dealing with acid mine drainage as to treatment levels, costs, and evaluation of abatement schemes, predictions of the quantity and quality of the discharges are needed. An acid mine-drainage model is presented in this paper. In essence, the model is a hybrid of computer programs for stream flow simulation and acid mine drainage. Two major aspects of the model are discussed: mine-water generation and acid-load production. The former is based on hydrologic concepts and the latter on pyrite oxidation kinetics and oxidation product removal. The total model is programmed for the high-speed digital computer. The major inputs are: climatological, basin characteristics, and mine characteristics data. By the use o f the hydrologic model the amount of water that flows through the pyritic system is determined. From this information, acid loads removed by leaching, inundation, and gravity diffusion are then predicted. The outputs from the total model are: average daily mine-water discharge, the associated acid concentration or load, plus the average daily flow in the receiving streams or at basin outlets. The capabilities of the separate models have been tested individually and the joint model has been applied to a small drift mine in southeastern Ohio.

Jan 1, 1975

By R. S. Shoemaker, D. L. Harris

Past investigations into the possibility of concentrating the low-grade iron ores of the Gogebic Range in Wisconsin have been hampered by the complex association of the constituent minerals. In part the problem arises from the fact that the iron occurs essentially as two minerals, hematite and goethite, having nearly the same chemical composition but exhibiting different physical properties. Individual grains of these minerals are usually so small that the ore must be ground to a size finer than 325 mesh if substantial liberation of the minerals is to be secured. Appraisal of beneficiation tests on this iron ore requires, therefore, some method of determining quantitatively the contents of constituent minerals in the various products of the beneficiation. Because of the chemical similarity of the two iron minerals, chemical analyses do not provide a means of differentiation. Although the minerals are different physically, they are both opaque and friable, and as the ore must be ground to a very fine size for liberation to be secured, quantitative microscopic methods of analysis are extremely difficult at best. In an effort to overcome these analytical problems, a quantitative X-ray diffraction analysis method has been developed at the University of Wisconsin for the research program on iron ore beneficiation.

Jan 5, 1955

By M. J. Buerger

POSSIBLY the most puzzling features observed during a single-crystal deformation test are the appearance of slip striae on the surface of the crystal and the strengthening of the specimen.1 While the first phenomenon is mainly of theoretical interest, the latter is fundamental to all strain-hardening and cold-working processes in which the deformation occurs by translation. The plastic deformation of crystals has received considerable discussion2 and need not be reviewed here in any great detail. It has been observed, essentially, that after a certain amount of initial stress is applied, the surface of the crystal becomes covered with sets of parallel striae or rings which appear to divide it into thin slabs or slip blocks.3 The striae are the traces of rational crystallographic planes along which shearing movements are localized, these movements providing the strain which accompanies stress applied beyond pure elasticity. As deformation under the applied stress proceeds the slip blocks shear past one another, although the essentially single-crystal character of the specimen is unimpaired. All of the shearing apparently takes place in the immediate vicinity of the original slip striae without the appearance of new planes of movement.4 Since each increment of strain is attended by an increased stress requirement to continue the deformation, the crystal strengthens during the process.

Jan 1, 1928

By G. M. Ellis

When developing a mineral processing facility, the mining company management and engineering staff should have some knowledge of the construction industry in order to work with the contractors involved as a team. Of course, the situation varies with the nature of the project and its size, but relations among owners, engineers, and contractors always will be enhanced if the mining company has a knowledge of three construction industry facets: (1) the makeup of a construction company, (2) the functions performed by its staff, and (3) the various types of contracts and tendering procedures available. There are several options open to a company wishing to bring a new mine into production from the grass roots, depending upon corporate structure, capabilities, and financial strength. A company that already employs a substantial engineering staff may elect to manage and perform the design requirements itself, and may handle some or even all of the actual construction work. But in cases where bank financing is required, the loan is often dependent upon adequate professional construction help being used.

Jan 1, 1978

By B. G. Bunting, J. H. Johnson, H. J. Schock

This paper describes an experimental method for monitoring diesel-generated exhaust gas pollutants in a deadended drift to assess the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 32 m long and slightly downsloping, with an everage height and width of 2.4 and 8.6 m, respectively. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generate pollutants. Induction ventilation appeared to be the least effective of the three methods examined.

Jan 1, 1982

By A. J. Lynch, W. J. Whiten

Extensive research, ,development and plant application work has been done on automatic control systems for wet grinding and sulphide flotation circuits during the past twenty years. The result is that there is a good understanding of the process mechanisms, the effects which changes in different variables have on these processes, the procedure for design of control systems to satisfy particular objectives and the problems in the implementation of control systems. There is also an appreciation of the problems which are still to be solved. These are reviewed briefly in this paper. Other processes used for the beneficiation of fine particles have been studied in lesser detail. The control of dry grinding, coal flotation and gravity separation are mentioned briefly in this paper.

Jan 1, 1980

By C. W. Waidner

THE standard scale of temperature that it is attempted to realize in practice is the centigrade thermodynamic scale, as defined by Kelvin about the middle of the last century. This scale would be exactly realized with a perfect1 gas in an ideal gas thermometer, and is closely realized with the more permanent gases. From the departure of certain properties of these gases from those of a perfect gas, it is possible to deduce the amount of the departure of the temperature scales, defined by their use, from the thermodynamic scale. In nearly all the precise experimental work done during the latter part of the last century, it was necessary for the experimenter to establish his own gas-thermometer scale, and the labor involved in this was often greater than that involved in the prime object of the experimental work undertaken. The experimental difficulties involved in gas thermometry led to the establishment of temperature scales differing from one another by amounts considerably greater than could be accounted for by the differences in the properties of the gases used. Results were, therefore, expressed in terms of somewhat different temperature scales, snaking correlation of such results difficult and uncertain.

Jan 9, 1919

By Burton H. Boyum

GREATER depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Marquette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock.

Jan 1, 1947

Jan 1, 1914

By M. P. Nackowski

Geological engineering expanded its role and significance during 1966 in the areas of construction, raw materials exploration and inventory, water supply and pollution, mechanical properties of earth material and regional environmental planning. Efforts varied immensely in scope and magnitude, in simplicity, difficulty and importance. Observations, measurements, and analysis encompassed both simple and sophisticated procedures. CONSTRUCTION Activities in construction ranged from preliminary to detailed evaluations of sites, development of preventative measures and designing corrective measures following construction failures. Most investigations concerned dam sites, highway locations and slope stability, building sites, tunnels and underground storage facilities.

Jan 2, 1967

By A. S. Yue

Small-angle tilt boundaries have been observed in a lamellar eutectic structure. These boundaries are morphologically similar to a theoretical till boundary originally proposed by Burgers. The production of a small-angle tilt boundary in the lamellar eutectic structure is attributed to the formation of an indentation on a planar solid-liquid interface during growth. Constitutional supercooling due to the accumulation of impurity atoms ahead of the interface is primarily responsible for the generation of an indentation. The distance between two faults of like sign, designated as lamellar fault distance, is calculated by the Burgers equation for small-angle boundaries. It was found that the lamellar fault distance decreases exponentially and the tilt angle increases exponentially with freezing rate. SMALL-ANGLE tilt boundaries have been observed in many crystals in the as-grown states by etching techniques. However, a detailed substantial proof for revealing the presence of dislocations in the form of etch-pits was recently accomplished by Vogel. These boundaries are described as an array of dislocations of like sign. The angle of tilt associated with a boundary is treated theoretically by Burgers3 and is given by 0 = b/D for small tilt-angle where b is the Burgers vector of the dislocations and D is their average spacing. During the course of experimentation on the solidi fication of the lamellar Mg-32 wt pct Al eutectic a microstructure which was strikingly similar to a dislocation tilt boundary was observed. An example of the type of microstructure is given in Fig. 1, which shows a combination of transverse and top sections of the lamellar eutectic structure. The lamellae of the top section on one side of the apparent tilt angle are not parallel with those on the other side. Consequently, some lamellae must be terminated somewhere. Fig. 1 shows that the termination of lamellae is analogous to a dislocation tilt boundary in a crystal lattice originally proposed by Burgers. This work represents a closer look at such structures. The factors governing the production of the small-angle tilt boundary are discussed in terms of the freezing condition and impurity distribution in the melt. The effect of freezing rate on the distance between two faults, designated as lamellar fault distance, and the tilt angle is also described. In addition, the lamellar fault distance is determined by means of the Burgers equation for small-angle tilt boundary. EXPERIMENTAL PROCEDURE The slightly impure Mg-32 wt pct Al eutectic rods, 5/8 in. in diam and 12 in. long, were made from 99.99 wt pct Al and 99.98 wt pct Mg and were cast in a high-purity graphite mold. Some of these rods were purified by zone-refining the eutectic using direct-radiation helical-coil furnaces5 A molten zone about 2 in. long was passed through the cast rods at a speed of 5.3 x 104 cm per sec for ten passes of the molten zone. Before the freezing experiment was begun, 2-1/2 in. of the material from the head and tail ends of the zone-refined eutectic were removed from the rod to eliminate any impurity. The freezing experiments were carried out under controlled conditions,8 using a protective atmosphere of purified argon. At the end of each run, observation of the tilt boundary was made throughout the entire length of the rod with a light microscope on the top, longitudinal, and transverse sections (three mutually perpendicular sections) of the lamellar eutectic solid. The experimental data used for the determination of interlamellar spacing and tilt angle were taken from the middle portion of

Jan 1, 1964

By Frederick Laist, Howard Aldrich

The object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the- results obtained. A general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, 20 ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the dots, thus cutting down the draft. The volume of gas through

Jan 1, 1915

By Lewis Stockett

During the year 1903, a building having machinery corresponding to ail anthracite-coal breaker was erected at the town of Stockett, Cascade county, Mont., for the purpose of breaking-up and cleaning bituminous coal. The coal is mined from a vein of the Kootenai group of the Lower Cretaceous measures having the following section: The vein is nearly horizontal in position, and each bench differs in quality as shown in Table I.

Jan 1, 1905

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district f origin. This paper will deal ' with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914

By W. L. Kendrick

At Henderson, Nev., Manganese Inc. is mining by open pit methods a low grade manganese ore averaging 21 pct Mn, concentrating it to 42 pct by flotation, and agglomerating it to produce nodules of metallurgical grade-about 48 pct Mn. The striking aspect of the whole operation, and one that has considerable effect on nodulizing, is the use of approximately 250 lb of reagent per ton of mill feed. For many years rotary kilns have been used for drying, calcining, clinkering cement and other products, and burning lime. Their use for nodulizing or agglomerating a metallic ore is new-first reported in this country in 1904, when a small rotary kiln at South Chicago was employed to nodulize flue dust from a blast furnace. After a short time this process was replaced by sintering.

Nov 1, 1956

By W. D. Forgeng, B. F. Decker

IT has been known for almost a century' that silicon and nitrogen combine when heated to a high temperature. Three nitrides have been reported, SiN, Si3N,, and Si,N, containing 33.3, 40.0 and 42.9 pct nitrogen by weight, respectively. The existence of SisN, is well established but that of Si,N, and SiN is doubtful. The first systematic study of the reaction between silicon and nitrogen was made in 1910 by Weiss and Engelhart" who determined the rate at which silicon absorbed nitrogen at temperatures from 1250°C to

Jan 1, 1959

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are' shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Proc¬esses in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1. 2 Taggart, and Yeele.

Jan 1, 1943

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By T. Leser, A. W. Jenike

The problems of caving and underground subsidence can be considered as the failure of a highly compacted rock and its subsequent flow in the form of broken rock. The problem is complex because the propagation of failure and flow have to be considered simultaneously; the yield strength of the virgin rock and the broken rock are different; and, while under certain conditions it is sufficient to consider the virgin rock as homogeneous, the density and the yield function of broken rock are both pressure and time dependent. A study of the failure and flow of solids with a pressure dependent yield function has been published recently by Jenike.' In this paper the density of the broken rock is assumed to be only time dependent and the consequences are examined in the case of one-dimensional vertical subsidence into an initial cavity. The following describes an attempt to develop a tool which, in combination with other tools, may lead to mathematical solutions of real problems of caving and subsidence. STATEMENT OF THE PROBLEM An underground cavity of horizontal cross section 4 = 1 and height 6 is assumed to exist at some depth below the surface. At the time t = 0 rock above the cavity fails and completely fills out the cavity with expanded broken material. With passing time the broken rock consolidates and subsidence proceeds continuously upuard in a vertical shaft. The phenomenon is one-dimensional (see Fig. 1). The problem consists of finding the displacement and the velocity with which the frlmt of the subsidence (wave front) moves upward as a function of the time and of the rock properties. DIFFERENTIAL EQUATIONS CONTROLLING THE PHENOMENON With the assumptions that the broken rock is a continuum and that the subsidence occurs continuously, we can apply the one-dimensional differential equation of contitiuity (conservation of mass) and the equation of preservation of momentum The latter equation is replaced by an assumed relation based on experience, which takes care of the

Jan 1, 1962