Search Documents

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By Pedro Antunes Amaral

Currently there is a constant and essential concern of preserving nature. Over the years the concern with the environment is increasing, new environmental laws are emerging and being applied more rigorously and consequently emerge economic needs and mineral processing practices and other materials. In this sense briquetting becomes an alternative to fine particles agglomeration by means of pressure and or temperature, with the aid or not of a binder, which allows to get a product not only compressed, which presents shape, size, and adequate mechanical properties. The reduction in volume of the material in some cases (beyond the technological benefits) also allows fine materials can be transported and stored more economically, safely and effectively. The production of coke is greater as the content of better coking coal is, thus he low capacity coking coal is not much used in coke ovens. This research aims to demonstrate that briquetting of mineral coals with low coking coal capacity is possible, additionally allows increased coke production, obtaining then a better yield of coke. Basically they take advantage of low price of no coking coals without changing the quality of the coke produced. Anyway, briquetting became a smart alternative to aggregate values, economy and care for the environment.

Oct 30, 2017

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Claude Gaspard, Stefan Wahlund, Daniel Cavalier

A point of great importance in the cold rolling process for automotive sheet is the cleanliness of the strip, particularly critical in case of batch annealing with no degreasing line or inefficient cleaning before continuous lines. In this specific cases, pollution of the strip surface could be prohibitive when rolling in the early stands of tandem mill with conventional forged work rolls as ground. The strip cleanliness strongly deteriorates during rolling particularly with high roughness rolls: iron fines are generated at the strip surface due to friction and stick on the sheet. It is well known that chrome plating on ground forged rolls in the early stands improve the strip cleanliness. This paper summarizes the results of 3D surface roughness topography studies on forged work rolls, with and without chrome plating, combined with sheet cleanliness measurement during rolling. It shows that a well determined topography has to be obtained on the work rolls used in early stands in order to roll in the mixed lubrication regime, as described by the Stribeck curve, minimizing the friction coefficient and therefore optimizing the cleanliness of the rolled sheet. The main roll roughness parameters to take into account for that purpose are the roughness level Sa, and even more, the Kurtosis parameters Sk, Spk, Svk and Ssk. The ideal surface morphology promotes deep valleys to the detriment of peaks, leading to a roll surface capable of retaining/trapping oil in the valleys, while peaks are minimized, thus reducing the friction in the roll bite and the amount of iron fines produced. To achieve this objective, new grinding wheel technologies are currently developed, in dialogue with wheel manufacturers, to create such ideal morphology of roughness well adapted to HSS forged rolls.

Oct 1, 2019

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Thorsten Müller

In order to increase the production of Advanced High Strength Steel (AHSS) as well as to fulfill the growing expectations of various industries served, steelmakers must have wide- ranging know-how in terms of plant technology, operation, processes, quality control and, last but not least, know-how for AHSS including certification procedures. MET/Con is highly focused on the production of coated AHSS with tensile strengths higher than 600 MPa. Common heating and cooling technologies are unable to handle high alloyed steel grades – pre-oxidation and rapid cooling technologies have been developed to face these new challenges. MET/CON and Drever International have the knowledge to produce newest steel grades with these technologies.

Jul 30, 2018

By Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Antônio Cezar Faria Vilela

A minor change in the chemical composition and temperature affects the slag viscosity, which has a great extent of the physical properties in regarding refining slags. Optimizing those parameters may affect the steel cleanliness. The viscosity measurement process is considered expensive, so the cost-effectiveness does not favor the measures at high-temperatures. Alternatively, it is possible to apply mathematical models or thermodynamic softwares to obtain viscosities for a given range of chemical composition and temperature of slags. The present work contemplates a validation of the experimental data, collected in the literature, with a calculated data and proposes an accurate representation of iso-viscosity curves applied for secondary steelmaking slags, covering the composition ranges: 0–100 wt.% CaO, 0–80 wt.% SiO2, 0–77 wt.% Al2O3 and 0–15 wt.% MgO (CSAM) system at 1500ºC. The viscosity representation fields include fully liquid and a partially liquid slags in the CSAM system and the viscosities were calculated using the FactSage 7.2 (for Liquid Phase) and the Roscoe-Einstein equation (for Phase mixture) for a total of 5976 slags. The preliminary results indicated that there is a great convergence between the calculated and experimental viscosities data, promoting an efficient approximation of the iso-viscosity curves for the CSAM slag system in the high-temperatures.

Nov 1, 2019

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By Larissa Agrizzi Ronqueti

The effect of coiling temperature on selective oxidation behaviour of binary and ternary iron-based model alloys containing different contents of Si or Mn were investigated by SEM and SIMS. The experiments were carried out with a temperature ranging from 450 °C to 700 °C, under N2-5%H2 gas flow with a Dew Point of -3.3°C, for different durations. SEM images of binary iron-based model alloys revealed a decrease of grain boundary oxidation depth with increasing Silicon or Manganese content. At 530°C and 600°C SIMS results showed no Silicon diffusion toward surface, contrary to the results analyzed for Fe-x%Mn. Tests results and Wagner’s theory application (specific cases Fe-0.2%Si and Fe-0.5%Si) showed that grain boundary oxygen diffusion coefficient “DoGB” is almost 60 to 70 times faster than oxygen bulk diffusion coefficient. These results helped to broaden knowledge of single-element effects on grain boundary oxidation, in addition, will contribute of the future works in new steels with complex alloy compositions.

Aug 17, 2017

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018