Search Documents

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By Walter E. Kramer

The advantages derived from the use of pellet burdens in blast furnaces are so great, that hematite ores are being converted into pellets in greater quantities each year. The conversion of these ores into pellets appears on the surface to be relatively simple. In reality, this is not so. Serious difficulties are encountered in drying these pellets that do not exist in the drying of taconite concentrate pellets. The ores that present problems are goethite and earthy hematites. Green pellets prepared from these ores have very law shock temperatures, 200-600° F. The shock temperature of a green pellet according to our definition is the highest initial temperature to which a green pellet may be exposed without suffering decrepitation. Decrepitation may involve spalling, fracturing or total disintegration. The poor shock properties of these green pellets result from the inability of the vaporized water to escape freely and easily as it is formed with¬out affecting the integrity of the pellet. As a consequence, the pellets must be carefully dried prior to induration. This careful treatment is costly. The slow drying process restricts productivity and requires larger furnaces than desired. The use of an additive to elevate the shock temperature of the green pellets would increase productivity. Bentonite is used in some pellet plants to improve balling but it raises the shock temperature only slightly. Nalco became interested in the shock temperature problem because of its activity in the development of organic pelletizing aids for taconite concentrates. The findings reported here are an outgrowth of our experimental work on the development of shock temperature additives.

Jan 1, 1967

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By William Wargo

The basic reason for lining underground cavities is to keep the cavity open during its useful life by providing adequately for the support of the surrounding rock and for the necessary degree of water tightness. This covers the entire field of support methods from the simpliest timber support to reinforced concrete in all its variations as applied to tunnels, galleries or shafts. The problem involved in the design of more efficient and economical lining systems for even bigger cavities has been magnified by increased speed of advance made possible by better blasting tecniques, improved tunneling machines and more efficient material handling. Tunnel lining today requires a disproportionate amount of time and money compared to other operations mostly due to the manuel labor involved in its installation. One solution to this problem is the developement of an entirely new concept in tunnel lining designed notoonly to overcome this bottleneck but also to open up the field for further increases in speed of advance. This new lining system acts first as a fast protective armour then becomes the concrete metal form and ends up as reinforcement sheet inside the concrete lining. This system developed and manufactured by Bernold A. G. of Switzerland since October 1968 has been installed in 25 applications in Europe under all ground conditions from stable rock to unconsolidated ground.

Jan 1, 1970

By H. H. Murray

In the past thirty years, there have been a large number of ownership changes in the industrial minerals arena and many medium to large companies have made industrial mineral acquisitions. Industrial minerals are exceedingly important to the achievement and maintenance of a high standard of living in the United States and in other developed countries. In the developed countries of the world the value of industrial minerals exceeds the values of the metallic minerals. In the U.S., the value of our industrial minerals is some 2 112 times that of the value of our metallic minerals. Almost every single thing we use or touch in our daily lives can be related to an industrial mineral. Examples are the construction industry, agriculture, ceramics, paper, paint, plastics, electronics, glass, petroleum, and many more in which an industrial mineral or minerals playa functional role. Industrial minerals are exceedingly diverse in their values, properties, and applications. Sand and gravel is an example of an essential industrial mineral commodity which has a low price but moves in very high volumes. Geographic location of this commodity is critical because of transportation costs. High calcium limestone or marble has a moderately high price particularly if it is white enough for use as a pigment or extender. This moves in moderately high tonnages and location is not as critical be-cause it can be shipped for considerable distances and still be competitive. Some specialty industrial minerals such as a white tale or white bentonite sells at a high price at low volumes and geographic location is not a major factor in marketing. Prices of industrial minerals do not tend to be cyclic and generally keep up with inflationary increases. Because of the diversity of industrial minerals very careful analyses of acquisitions or divestitures must be undertaken by buyers and/or sellers in order to prevent serious mistakes.

Jan 1, 1994

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company's open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By T. D. Kaufmann

When Dr. David Gully solicited this paper last spring a few questions basic to commodity trade between the U.S. and world markets appeared perplexing. Why, for example, when the demand for aluminum was at a peak and when little expansion of capacity had taken place, was the dollar price half of what it had been at the previous peak? Or, why in 1984 when imports surged by 50% as the U.S. economy pulled out of its recession did the dollar not fall, but rather rose by 35%? And, why when the experts all seemed to agree that the dollar was grossly overvalued did the price of gold continue to decline? Surely these were extraordinary times for the mineral economist. When this paper was written in late July, 1985 the answers seemed clearer. The prices of many commodities were not low - the dollar in which they were denominated was too high. In other currencies many commodity prices were indeed high. The dollar was overvalued in trade terms by some 40% caused by an influx of short term coupon investments made by foreign money managers to take advantage of the higher short term interest rates in the U.S. relative to other international banking centers. With a decline in the relative difference in interest rates, an unhealthy buildup of foreign bank accounts and a perception that the dollar would fall, the dollar did start to decline rapidly.

Jan 1, 1985

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By William E. Robinson

Our earthly treasures are being quickly depleted. We have experienced what can happen in an energy crisis. You have read and heard all kinds of stories as to what caused this crisis. On the surface it would seem that all of a sudden a situation becomes a crisis whether it be fuel, potatoes, beef or whatever. Well, of course, they don't just happen. There is always a little fore-warning here, an indicator there. Someone recognizes a sign of potential trouble but is ridiculed when he forecasts it. We are running out of sand: Producers of aggregates who can say today ... "That couldn't happen to me", can well be awakened tomorrow to the cold fact of reality. It could come from any number of directions. Depletion is mostly foreseeable but zoning isn't. Legislation can also be sudden death to availibility. With the ever growing population moving into the rural countryside, available deposits are being sold either to developers or being zoned for restricted use. The fact that a gravel pit or quarry is located on a particular plot has not fazed some of the local planning boards when they decided to place the adjoining property in a residential Zone A. Proponents of zoning preach that such use is necessary to insure that the land will be put to its best use. Planning boards establish the best places for schools, homes, shopping areas, factories, etc., so that the individuals or groups are in harmony with each other. This is usually done to date without thought or consideration to the geological importance or potential of the area. Today over half of the United States is living under some form of land use restriction. Little consideration has been given to what lies under the ground to be zoned. Fortunately, the states are slowly getting around to geological surveying. I feel that it is about time that state and federal authorities institute governmental restrictions to prohibit or control local zoning ordinances which would deplete or deny an area of its natural resources. While I could continue for the balance of my time just on this facet of our industry's problems, my point is: How sure are you of your next load of sand? I could be well laughed at by some of you for saying that there is an alarmingly rapid disappearance of "nearby" sand and gravel reserves in many areas of the country. A questionable statement, except to those producers where depletion has already taken place.

Jan 1, 1974

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By J. Litsenberger, T. E. Marshall, L. Burke, R. Melville, A. T. Iannacchione

Excessive levels of horizontal stresses cause ground fall hazards in underground mines in the Appalachian Basin. At an underground stone mine in Pennsylvania, a modified stress control mine layout is reducing the hazardous conditions associated with excessive horizontal stresses. A microseismic monitoring system is in place to measure levels of rock stability and provide information on the effectiveness of the design technique. The microseismic data is supplemented with frequent and extensive mapping of roof falls and roof rock damage. Findings to date show that the stress control layout provides more stable conditions and thus a safer environment for the mine workers.

Jan 1, 2001