Search Documents

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By Joseph Gildner, Donald J. Phelps, Jürgen Laubbichler, Christopher Tattersall, David McAllister

The Beacon Hill Station and Tunnels portion of the Sound Transit Central Link Project consists of one mile of twin rapid transit tunnels, an underground station, portals and ancillary works constructed in an urban environment. Presently under construction, the station will set a number of North American firsts including deepest soft ground excavation carried out using the Sequential Excavation Method (SEM).Located in highly variable glacial soil deposits ranging from soft, water bearing sands to stiff, slickensided clays, the station complex and running tunnels proved to be technically challenging during design. Meeting these challenges necessitated an extensive geotechnical investigation, a trial shaft, and state-of-the-art numerical analyses to develop ground conditioning, pre-support, excavation support and structural design. A comprehensive risk identification and mitigation program, and innovative procurement strategy were incorporated into the design and contract bid documents.

Jan 1, 2005

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

The Coeur Rochester Mine is one of the largest and lowest cost primary silver mines in the United States. In January, the mine surpassed 3.1 kt (100 million oz) of historic silver production. Rochester is owned and operated by Coeur d’Alene Mines, the world’s largest primary silver producer. Rochester is the world’s seventh largest silver mine. It also produces gold — more than 31.1 t (1 million oz) in historic production. Cash operating costs have averaged 8 cents/g ($2.58/oz) of silver since operations began in 1986.

Jan 1, 2004

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By K. Y. Vasioutchkov, Y. F. Vasyuchkov, B. M. Vorobjev

In general a term "unconventional mining or "non-traditional mining technology" getting more and move familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in [Figure 1:] One of the greatest potential for coal utilisation during the beginning decades of on coming cetury is the synthetic fuel-gas derived from coal as a product of coal gasification. It is quite logical to enrich this gas before burning it with natural gas, that is methane, contained in coal measures. Thus it is reasonable to suggest a new concept of unconventional coal mining and utilization technology featuring integrated methane drainage with coal-gas combined cycle. Proposed unconventional technology of coal mining is characterized with: - opening up a coat deposit through boreholes, drilled from the surface and used for coalbed methane drainage as well as for coat gasification in situ; - aggregation of methane producing and coal gasification station on mining side with thermo power plant on the electric power generation side in one integrated industrial enterprise. The further improvement of the conventional coal mining technologies both surface and underground could give only insignificant results in economical, ecological and social aspects, but would not be able to provide basic requirements of the XXI-st century. Significant increase in economical efficiency, cardinal humanization of coal mining and basic improvements in environment protection would be achieved through introduction and implementation of innovative or unconventional coal mining technology. These considerations are applied on both coal production and coal utilization sides as far as coat based energy generation is concerned. Now a general opinion is widely spread that an application in the same manner of the traditional technologies of coal mining and electric power generation would inevitably cause further irreversible damage of the global eco-system, notwithstanding the certain environment protection measures being taken. Keeping the recent pace of the eco-system degradation the whole our civilization would be in danger. Thus the solution of this problem is to be found in developing, promoting and implementing in industry unconventional coal mining and modern advanced clean coal technologies. Coal reserves with favourable conditions at shallow depths are -being rapidly depleted in all countries with developed coal industry. So in nearest future more coat will be mined from deeper levels with higher operational expences and with lower labour productivity. For example in Russia only 20% of proven coal reserves can be specified in quality as easy mined reserves, i.e. coal reserves with a good minability. Unconventional (borehole in situ) coal mining enables us to mine difficult coal reserves, deposited under unfavourable geological conditions with higher economical and socio-ecological efficiency than that in conventional coal mining, in view of these the basic principles and concepts of coal mining and coal utilization for energy generation should be reconsidered taking into account the latest achievments in underground coal gasification/combustion, coalbed methane extraction, clean coat technology and advanced developments in environmental engineering. The authors have developed a new concept of ecologically clean and resource saving coal-gas electricity, protected by a patent of Russian Federation (1995). The main principles and technological features of these conceptual technologies are explained hereupon. It should be a break through into a coal mining technology of new generation, which is known as unconventional coal mining technology. Under current global energy policy, transection to the new generation of coal mining technology is inevitable. Now we are standing at the treshhold of the coat's regeneration based on integrated unconventional coal mining and innovative coal fueled electric generation technologies.

Feb 24, 1997

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

By Eldon L. Abbott, Rebecca K. Bolan

The Florida Department of Transportation, Florida’s Turnpike Enterprise is studying the feasibility of a 1128 meter (3,700 foot) vehicular tunnel to provide direct access for Port of Miami traffic to/from I-395, I-95, SR-836 (Dolphin Expressway) and Miami International Airport. Both Bored and Immersed Tube tunnels were evaluated and re-evaluated for constructing two, two-lane, 11.9 meter (39-foot) diameter tunnels beneath the Main Shipping Channel lying between Watson Island and the Port of Miami on Dodge Island in Biscayne Bay, Miami, Florida, USA. Bedrock Geology of South Florida is predominately very permeable, vuggy limestone with sand seams and occasional voids. Groundwater inflows in deep cut-and-cover excavations, tunnel buoyancy, grouting, maintenance of Port operations and potential/possible environmental impacts to Biscayne Bay were significant issues.

Jan 1, 2005

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012