Search Documents

By P. R. Jochens

South Africa depends to a considerable measure on the exploitation of mineral reserves and the processing of these minerals. One of the prime requirements for the mining and metallurgical industry to continue in this vital role is access to sufficient energy in a suitable form. Hence, four important questions are discussed: Does South Africa have sufficient energy for the processing of its minerals and metals! Will the cost of energy allow South Africa's minerals and metals to compete on world markets? Can mining and metallurgical processes become more energy-efficiency Can mining and metallurgical processes be adapted to the various forms of energy that may have to be utilized in the future? It is concluded that about 26 per cent of the extractable reserves of coal would be required in the mining and processing of 50 per cent of South Africa's reserves of gold, platinum-group metals, copper, iron, ferrochromium, and ferromanganese. However, the reducing agents required exceed the extractable reserves but not the total estimates of mineable in situ resources of metallurgical coal and anthracitic coal. Even under the severe constraint that coal could become virtually the sole source of energy, only about three-quarters of the extractable reserves of coal would have been consumed by the year 2025. The reasonably assured resources of uranium metal that can be recovered at less than $80 per kilogram are considerable and, at current conversion efficiencies to electricity, are equivalent to one-fifth of the extractable reserves of coal. The rate of exportation of energy in the form of U30. was about five times that of coal in 1978. It is pointed out that the price of energy has a direct effect on the competitiveness of metals, and, although constituting only a small proportion of the selling price of precious metals, it represents a significant proportion of the selling price of copper and metals recovered from oxide ores. The scope for the conservation of energy appears to be greater in the extraction and conversion of primary energy-carriers to electrical energy than in other mining or metallurgical fields. Provided that alternative sources of energy can be converted to electrical energy, they can be applied to the mining and metallurgical industries. The decision as to which type of energy should be used in specific mining and metallurgical situations is complicated, and is likely to be subjected to closer scrutiny than in the past. The hope is expressed that the tentative conclusions reached will give rise to more-quantitative analyses from those qualified to undertake such an exercise. Inevitably, the questions asked at the outset give rise to more questions, and the more interesting ones are posed in the context of each conclusion.

Jan 1, 1980

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By D. C. Krige

The estimation of the tonnage and grade of payable ore in a mine and the correct policy of selective mining based on such estimates, is of vital importance to the mining engineer it is surprising, therefore, that more attention has not been devoted on the Witwatersrand to the scientific improvement of mine valuation methods. At present these methods consist almost entirely of the application of simple arithmetic and empirical formulae guided by practical experience, and ignore the many advantages to be gained from a careful statistical analysis of the behaviour of the gold values. The science of statistics has expanded rapidly during the last two decades and its value as a powerful and indispensable tool is now recognized not only by research workers and scientists but also, ever-increasingly, by the commercial and industrial world. This being the case it is noteworthy that in a mining field such as the Rand with its highly developed and advanced mining methods, singularly little attention has been paid to the analysis of mine valuation problems on a modern statistical basis. This omission is even more striking when cognizance is taken of the wealth of sampling data concerning the gold ore which is available and of the far-reaching decisions and deductions constantly being based on such data. Some contributions have however been made from time to time towards the application of statistics to mine valuation on the Rand (References Nos. 7, 8, 9, 11, and 12), but none of these have been generally applied in practice and a systematic practical approach based on clearly deemed fundamental concepts still appears to be lacking. The object of this paper is, therefore, to define these statistical concepts and to indicate briefly the lines along which statistical methods can be applied profitability in solving some of the existing problems and in improving the general standard of mine valuation on the Rand For this purpose a knowledge of mathematical statistics is essential, but as this paper is primarily intended to provide the mine valuator with a practical introduction to statistical application in his field, the mathematics is confined to a short annexure, together with references from which details can be obtained.

Jan 1, 1994

By C. Klutke

This paper outlines a simple methodology for mineral characterization, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterization of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilized at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used; however, this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterization of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4?4.7 and zircon RD4.6?4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide, with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By A. K. K. Rompel, G. K. Chunnett

Introduction Structure appears to be of secondary importance to the Bushveld Complex when viewed from a distance. However, a closer look already reveals that large fault zones bound the Bushveld Complex. These fault zones are deep-seated crustal lineaments of continental magnitude such as the Thabazimbi-Murchison Lineament, the Johannesburg-Barberton Lineament, the Palala Fault zone and the Rustenburg fault. Furthermore, the Bushveld Complex is transected by large faults such as the Vlakfontein Fault, visible in the Pilanesberg, the Steelport Fault and the Laersdfrift Fault in the Eastern Bushveld, the Brits Graben, and a multitude of dyke generations (Figure 1). When pursuing structures on a project scale, the lack of outcrop, particularly in the western part of the Bushveld, is of no help for the exploration geologist. Consequently, the first dataset that needs to be considered is the Landsatimagery. Older Landsat TM 5 or newer Landsat ETM 7 will immediately reveal areas of outcrop for field visits, and, after further processing, indicate the geological units, in particular the platiniferous Critical and the Main Zone of the Rustenburg Layered Suite (Figure 2). Airborne magnetic surveys are the subsequent dataset necessary for any decent interpretation of the geology under the ?Black Turf? cover. Currently Anglo Platinum acquires aeromagnetic surveys with a flight height of 20 m and a line spacing of 50 m. These result in high-resolution imagery absolutely crucial for dyke delineation and dip modelling, stratigraphic layer detection, IRUP detection and possibly pothole discovery and fault delineation (Figures 3 and 4). However, the aeromagnetic surveys and the Landsat imagery reveal structures very much confined to the surface and may be hundreds of metres above the platiniferous reef horizons. This may lead to inaccuracies. When determining the underground structures for shaft sinking and mine planning, a 3D seismic survey is advisable. Too many shafts have been sunk in the Witwatersrand Basin for gold and in the Bushveld for platinum without sufficient information of the structure beneath. Recent 3D seismic surveys in the Bushveld have proven the technology and visualized the reef horizons and led to an interpretation of the underground structure (Figures 5 and 6). [ ]

Jan 1, 2004

By T. F. Muller

In recent years, a great deal has been written and spoken, both in our country and overseas, about the dangers posed to the environment and the ecology by mining operations. The object of this address is to put this problem, and it is a real problem, into reasonable perspective. I shall try to present the various facets that merit consideration as objectively as possible. In doing so, I shall examine the following factors: Book review National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline, and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

1. Book reviews A report by the Monopolies and Mergers Commission on the efficiency and. costs in the development, production and supply of coal by the NCB (Chairman G. Le Quesne). London, Her Majesty's Stationery Office, Jun. 1983. £20 for report and appendices (2 vols). Reviewer: M. J. Martinson Canadian mines handbook 1983-84, edited by M. R. Brown. Toronto, Northern Miner Press Ltd, 1983. 444 pp. $22. Reviewer: Northern Miner Review Editor 2. New publications Developments in geophysical exploration methods-5, edited by A. A. Fitch. Barking. Applied Science Publishers Ltd (Ripple Road, Barking, Essex IG II OSA, England), 1983. 255 pp. £35.75. High-pressure researches in geoscience--behaviour and properties of earth materials at high pressures and temperatures, edited by W. Schreyer. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. 545 pp. DM 188. Dynamics of oil and gas accumulations, by Alain Perrodon. Pau, Elf Aquitaine (Documentation Centre Micoulau, 64018 Pau, France), 1983. 368 pp. 240 FF. New paths to mineral exploration, edited by F. Bender. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. 169 pp. DM 58. Results of the First Workshop on Standards in Geothermics, edited by R. Haenel and M. Gupta. Stuttgart, E. Schweizerbart'sche Verlagsbuchhandlung, 1983. DM 98. E&MJ book of jlowsheets edited by Paul C. Merritt. New York, McGraw-Hill, 1983. 214 pp. $42. 1983 E&MJ international directory of mining. New York, McGraw-Hill, 1983. 808 pp. $70. The future of heavy crude and tar sands - volume 11. New York, McGraw-Hill, 1983. 1300 pp. $1l0. 3. Mineral Policy and Energy publications Aluminium, by A. Johnston. 12 pp. . Arsenic, by J. J. Hogan. 4 pp. Cobalt, by D. G. Fong. 6 pp. Selenium and tellurium, by A. G. Johnston. 7 pp. Stone, by D. H. Stonehouse. 13 pp. Uranium, by R. T. Whillans. 16 pp. 4. Mintek publications Report M88 'l'he recovery of platinum-group metals and gold by the lead-collectionstep of thefire-assay procedure. Report MI04 The preparation and analysis of reference materials, and the provision of recommended values. Progress report no. 5. Report Mll1 The determination, by flow-injection analysis, of iron, sulphate, silver, and cadmium. Special publication 3 A guide to the presentation of papers.

Jan 1, 1983

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semi-variogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semi-variogram model should take a value of zero, a value equal to the nugget effect or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semi-variogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3. ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model. ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and web courses, the definition of the semi-variogram is ambiguous as the formulae for semi-variogram models is not actually specified at zero distance6,7,8.

Jan 1, 2009

By S. R. Xie, S. Gong, E. P. Li, S. S. He, Y. J. Sun, S. J. Li

"Based on the complicated geological production conditions and abnormal strata behavior of the fully mechanized caving face No. 102 in the Xinyang Coal Mine, we analyze the breaking and forming process of distinguishing key block structures in close spaced coal seams. This analysis establishes an integrated mechanical model of these distinguishing structures. Furthermore, the horizontal force TAB generated by downward key blocks A and B is quantified, as is the Pressure PG exerted by key block B on caved gangue. Finally, the interaction mechanism is revealed. Analysis of the results using Mathematica reveal the following: 1. Both TAB and PG exhibit approximately inverse relationships to coal pillar width b; 2. TAB exhibits an approximately exponential relationship with mining height M of which the base is greater than 1; 3. PG exhibits an approximately arctangent relationship with mining height M. Combining these results with field observations, we conclude that the area in the vicinity of supports 100#–120# in the upper area of working face No. 102 is the likely zone of abnormal strata behavior. Thus, this area was classified as a key control area. Based on these results, the graded support control technique is proposed. Application of this technique in the field resulted in a reduction in the rate of hydraulic support system malfunction from 47% to 7% in the key control area. In addition, during times of periodic mining pressure, the roof caving height value never exceeded 0.3 m and the maximum spalling depth never exceeded 0.2 m. Overall, the results indicate that this new technique has markedly increased the stability of surrounding support rock material. IntroductionClose-spaced coal seams are widely distributed in China, and mining proceeds from the uppermost to the lowermost seam (Zhang et al., 2008). In the case of coal seams in close proximity, a particular set of risk factors becomes pertinent. These include disturbance of lower seams during the mining of overlying ones and the decrease in mechanical stability of lower coal seams following repeated movement of key blocks in main coal seam roofs. This inevitably results in behaviour such as heavy wall spalling and support damage to fully mechanized caving faces in lower-lying coal seams, which necessitates a significantly increase in the measures to support surrounding rock material (Zhang et al., 2010; Huang et al., 2013; Xie et al., 2013)."

Jan 1, 2016