Search Documents

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

By J. Muralha

The paper presents the limit equilibrium equations for the analysis of toppling blocks on a rock slope. The safety conditions are assessed by a numeric procedure implemented in an Excel worksheet. The UDEC numerical program was exploited to validate the procedure. A probabilistic model considering the spacing variability of the discontinuities was developed to define the most relevant parameters in this kind of problems. La communication presente les equations d’équilibre limite pour l’analyse de blocs rocheux sur une pente. Les conditions de securité sont évaluées par une procédure numérique en Excel. Le logiciel UDEC a été exploité pour valider cette procedure. Un modèle probabilistique a été developpé pour définir les plus importants paramètres dans ces problèmes. Das Referat stellt die Grenzgleichgewichtsgleichungen für die Analyse von umstrürzenden Blök-ken auf eines Felshang vor. Die Sicherheitsbedingungen werden durch ein numerisches Verfahren mit Excel beurteilt. Um die Gültigkeit des Verfahrens festzustellen, wurde das Programm UDEC benutzt. Ein die Klufabstandsvariabilität berücksichtigendes probabilistisches Modell wurde entwickelt, um die wichtigsten Parameter dieser Probleme zu bestimmen.

Jan 1, 2003

By Harushige Kusumi, Yuzuru Ashida, Toshiki Watanabe, Toshifumi Matsuoka

ABSTRACT: The technique of various kinds of numerical analysis offered remarkable results to explication of many rock mechanical phenomena. These techniques regarded a rock stratum as a continuum body and solved the governing equation of continuum mechanics by using finite differ-ence method, finite element method and/or others. Using numerical analysis based on continuum mechanics, however, the simulations of destruction phenomena caused by elastic waves and on the other hand, the elastic wave propagation which generated by fracturing events are quite difficult. In this paper, we express a rock stratum by a granular body model and develop a simulation tech-nique can simulate both wave phenomena and destruction phenomena at once. The DEM (discrete element method) simulation results are compared with finite difference solutions of elastic wave equation. Furthermore, we simulate Hopkinson effect by this proposed method. Hopkinson effect is famous as a destruction phenomenon caused by elastic wave propagation. ABRISS: In dieser Studie drücken wird eine Felsschicht durch ein Granularkörpermodell aus und entwickeln eine Simulationstechnik, die sowohl Wellenphänomene als auch Zerstörungsphänomene simulieren kann. Die Ergebnisse der Simulation mit DEM (Diskrete-Elemente-Methode) werden mit denen der Finit-Differenz-Lösung von Gleichungen elastischer Wellen verglichen. Desweiteren simulierten wir den Hopkinson-Effekt mit dieser vorgeschlagenen Methode. Der Hopkinson-Effekt ist als Zerstörungsphänomen berühmt, verursacht durch Fortpflanzung elastischer Wellen. RESUME: Dans cette étude, nous exprimons un lit de roches par un modèle à corps granulaire et développons une technique, permettant de simuler d'un coup le phénomène des ondes et le phé-nomène de destruction. Les résultats de la simulation DEM (méthode d'éléments discrets) sont comparés aux solutions à différence finie de l'équation d'ondes élastiques. En outre, nous simulons l'effet d'Hopkinson par la méthode proposée. L'effet d'Hopkinson est connu comme phénomène de destruction, causé par la propagation d'ondes élastiques.

Jan 1, 2003

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d'images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l'eau dans la roche. Une nouvelle technique expérimentale, se servant d'un identificateur principalement constitué d'iodure de potassium (KI), est proposée avec la méthode de l'analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

By M. Jacobs

Keywords: Smelting, converting, sulphide, sulphide smelting, platinum, platinum group metals, PGM, base metals, nickel, copper, matte, slag, furnace, electric furnace, Söderberg, electrode, granulation, converter, flash drier, sulphuric acid, acid plant, Ausmelt, Sirosmelt, pyrometallurgy, metallurgy, Anglo Platinum, South Africa Waterval Smelter complex is situated in Rustenburg, in South Africa?s North West Province. The smelter objective is to process wet concentrate to produce crushed, slow-cooled, sulphur-deficient nickel-copper matte rich in platinum group metals (PGMs), gold, and base metals for despatch to the Magnetic Concentration Plant at the Base Metals Refinery. Throughout its history, the smelter complex has been continuously upgraded in line with increasing production demand, changing feeds, environmental initiatives, and advances in available technology. The smelter receives filter cake and slurry from Anglo Platinum concentrators and joint ventures. Wet concentrate is fed through a flash drying process utilising coal-fired, fluidised bed hot-gas generators, to produce dry feed material for the electric furnaces and slag-cleaning furnace. For primary smelting, two electric furnaces are used, each with a rated capacity of 34MW. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is tapped periodically into refractory-lined ladles and granulated using high-pressure water jets, then dried through electrically powered pneumo-driers to become the main feed to the Anglo platinum Converting Process (ACP). Slag is tapped semi-continuously, granulated, and treated through the slag mill. The ACP treats the combined matte output of Waterval, Polokwane, and Mortimer smelters. It is a top-blown furnace, with furnace matte, air, and oxygen being injected into the converter via a lance submerged in the slag. Converter matte is tapped and bottom cast into moulds, slow-cooled, crushed, and despatched to the refineries. Slag is granulated and dried for recycling to the slag-cleaning furnace. ACP slag is fed to the slag-cleaning furnace along with a reductant and a sulphur source. Slag-cleaning-furnace matte is granulated for processing by the ACP, while slag is granulated and processed in the slag mill. The slag mill and flotation circuit treats granulated slag from the electric furnaces and slag-cleaning furnace to recover entrained matte containing valuable PGMs and base metal sulphides.

Jan 1, 2006

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By A. Tsekov, Stefan Neufeind, T. Angelov, G. Savov

"A complementary ion exchange/solvent extraction process for the recovery of copper from low-grade ores developed by Iontech Engineering Ltd. is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tonnes per year. Technical and economic aspects of three years of operational experience are comprehensively compared with the Asarel Medet copper plant in Bulgaria, which is utilizing conventional solvent extraction in the enrichment/purification step. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase (see Figure 1). After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.Although considered as “technology of choice”, SX to date is still suffering from several drawbacks, such as the risk of poor phase disengagement and the high capital costs of solvent-extraction plants. Especially, the processing of leachates with lower copper tenors (< 1 g/L) is often economically less attractive. As a result, tremendous efforts have been dedicated to the evaluation of alternative technologies to address these challenges."

Jan 1, 2015

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

A Life Cycle Assessment (LCA) of stainless steel production, including that of the nickel, ferronickel, ferrochromium and iron feedstocks was carried out using inventory data derived from the literature. The environmental impact categories considered in the study were Global Warming Potential (GWP), Acidification Potential (AP) and total (or full cycle) energy consumption. The effects of different sources of electricity (black coal, natural gas and hydroelectricity) were also examined in the study. The results of the LCA showed that when ferronickel is used as the nickel source, the total energy consumption for stainless steel production is approximately 50% higher than when nickel metal is used as the nickel source (75 MJ/kg cf. 49 MJ/kg). This result comes about largely because the Fe units in ferronickel have a much higher energy intensity than do the Fe units in pig iron, and the greater the use of the former at the expense of the latter, the greater is the total energy consumption. The results also showed that the production of ferronickel made by far the largest contribution (59%) to the total energy consumption for stainless steel production when this feedstock is used as the nickel source, but when nickel metal is used as the nickel source the contributions of the various stages are more evenly distributed. It was also observed that the electricity consumption of the electric furnaces used in the production of ferronickel, ferrochromium and stainless steel contributed approximately 50% to the total energy consumed in stainless steel production. Given the relatively low efficiencies associated with electrical power generation, significant reductions in the total energy of stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel, ferrochromium and/or stainless steel smelting stages, for example by utilising bath smelting processes.

Jan 1, 2004

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

INFACON conjures up many things for many people. For the fortunate few who have been actively involved with this event since its inception, it brings back memories of far places, stimulating debates and above all, the people who have over the years contributed to the outstanding success of the Congress and who have added to the wealth of knowledge on all aspects of ferroalloys. The International Ferroalloy Congress (INFACON) has been held every three years since 1974. INFACON X will be held in Cape Town in February 2004. Simple arithmetic shows that next year?s Congress should in fact be INFACON XI. Thus, one Congress was skipped. INFACON 74, as the name implies, was held in 1974, in Johannesburg, South Africa. The event was sponsored by the Ferro Alloy Producers? Association of South Africa (FAPA), the National Institute for Metallurgy (NIM - Mintek as it is known today) and the South African Institute of Mining and Metallurgy (SAIMM). You will see some of the same sponsors involved in INFACON X. Dr. Robbie Robinson, renowned academic and past president of the SAIMM, was the Chairman of the Organising Committee. The editor was Dr. Helen Glen. Anyone fortunate enough to possess a copy of the proceedings of this first Congress will agree that from a literary and technical perspective, it is still the benchmark for subsequent events. A unique feature of INFACON 74 was the use of rapporteurs (my first duty) to ensure that the discussions following the presentations were recorded (in direct speech) as accurately as possible. This involved time-consuming correspondence (can you imagine life before e-mail?) to all parts of the world between the author and the person posing the question, with the rapporteurs acting as go-betweens. It is understandable that the much-awaited proceedings only saw the light in 1975. The names recorded in the proceedings as the members of all six committees read like the who?s-who of the South African ferroalloy industry at the time: Dr. Peter Jochens, Mr. Harvey Reid, Mr. Piet Streicher, Prof David Howat, Mr. Sigurd Selmer-Olsen - to name but a few. The Congress was held in the new, very fashionable and upmarket Carlton Hotel in the CBD. In the Foreword of the proceedings, Dr. Robinson provides an insight into the event. Three hundred and thirty six delegates from twenty two countries attended the Congress, which was opened by the Honourable P.G.J. Koornhof, Minister of Mines. Again, the opening address makes fascinating reading. During the Congress an ad hoc committee was convened as the first International Committee on the Organisation of Ferroalloys Congresses, with representation from the main ferroalloy associations of the world. The following decisions were recorded: ? The Congress would be continued at three-yearly intervals under the name of INFACON ? Every third Congress would be held in South Africa ? NIM (Mintek) would provide the permanent secretariat. Six technical sessions were held, each preceded by a plenary address with a closing address by the session chairman. In all, thirty technical papers were presented. Prior to the closing address, a panel discussion on factors affecting the future of the ferrochromium industry provided stimulating debate in the form of a question-and-answer session. The hosting country for the next INFACON would be announced. Eventually, word got round that the next INFACON would be held in Japan. However, due to unforeseen circumstances, the event was cancelled ? thus no INFACON 77. INFACON 80 was subsequently held in Lausanne, Switzerland from 12th to 16th October 1980. The event was organised by IFPEO, Institut des Producteurs de Ferro-Alliages d?Europe Occidentale. The Congress was officially opened by the President of IPFEO, Mr. R. Björklund, who was also President of the Organising Committee. The technical sessions were held in the Palais de Beaulieu. The Congress was well attended by 400 participants from 28 countries as well as 100 accompanying ladies. A total of four plenary addresses and 18 technical papers were presented. As with the first event, an international panel discussion (questions and answers) preceded the closing address. In his closing address, Dr. Louw Alberts, Chairman of the International Committee on Ferroalloys and President of NIM, presented an insight into the factors affecting growth in the industry and where growth was likely to take place. Twelve exhibitors had stands at the Congress. Attendees could choose from four post-event tours to Belguim/France (SADACEM/Compagnie Universelle d?Acetylene et d?Electro-Metallurgie), France (CUAEM), Finland (Outokumpu Oy) and Norway (Elkem Fiskaa plant).

Jan 1, 2004

By W. Mackenzie

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines - mining, metallurgical, chemical, civil, electrical, mechanical and environmental - as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies - and hence no two development projects - are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource project&apos;s development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as `doing a feasibility study&apos;. But the principal purpose of a `feasibility study&apos; is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant - they are a prerequisite to the demonstration of a project&apos;s viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of `feasibility studies&apos; and provide guidance to minimum standards and best practice.

Jan 1, 2007