Search Documents

By J. D. Davis

THIS report gives results of an investigation of the carbonizing properties of the following eastern Kentucky coals: Elkhorn No. I bed, No. 28 mine, Wayland, Floyd County; Elkhorn No. 2 bed, Turner No. 5 mine, Drift, Flood County; Leatherwood (Haddix No. 5) bed, Leatherwood mine, Leatherwood. Perry County; and Harlan bed, Path Fork mine, Path Fork, Harlan County. The carbonizing properties were determined by Bureau of Mines-American Gas Association (BM-AGA) tests at 800° and 900° C. and by expansion tests in the sole-heated oven. Plastic properties were determined by tests in the Gieseler and Davis plastometers. The coals were tested singly and as blends with 20- and 30-percent low-volatile Pocahontas No. 3 coal. The dry, mineral-matter-free, fixed-carbon content of the carbonizing samples ranged from 56.7 percent for Elkhorn No. 2 to 59.7 percent for Leatherwood, and the heating values on the moist, mineral-matter-free basis ranged from 14,420 B. t. u. per pound for Elkhorn No. 2 to 14,720 for Harlan. The percentage of ash ranged from 2.9 to 6.1. The fluidity of three coals, measurer. In the Gieseler plastometer, ranged from 230 to 670 dial divisions; the fluidity of Elkhorn No. 2 could not be determined by this method. Blending lowered the fluidity of each coal; the fluidity of the blends containing 20 and 30 percent Pocahontas No. 3 ranged from 16 to 53 and from 8 to 17 dial divisions, respectively. Agglutinating values determined on silicon carbide-coal mixtures in the ratio 15:1 ranged from 3.8 to 6.3.

Jan 1, 1952

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By Keith Harris

The U.S. economy grew moderately in the second quarter of 1985 with real gross national product (GNP) recording a seasonally adjusted annual growth rate of 2.0%, up from the 0.3% growth of the previous quarter but significantly below the 7.1% growth of the second quarter of 1984 (table I). Personal consumption expenditures grew 5.3%, with purchases of durable and nondurable goods rising 7.4% and 5.1 %, respectively; nonresidential and residential fixed investment--the two components of fixed investment--grew 11.8% and 5.6%, respectively; and Government spending rose 3.6%. However, these gains were tempered by a major decline in the growth of business inventories (from $19.1 billion to $8.3 billion) and the continuing growth of the net export deficit (from -$28.4 billion to -$33.3 billion). While the high value of the dollar compared with other currencies has been a major cause of the expanding trade deficit, its value, as measured by the monthly Federal Reserve Board (FRB) multilateral trade-weighted dollar index, has declined over 17 index points from its February peak to 140.94 in July. The July dollar value was still high historically. The rate of inflation, as measured by the fixed-weighted price index for GNP, remained low at 4.1%, down from 4.3% in the first quarter, and employment continued to grow at a rate sufficient to keep up with new additions to the labor force. Civilian unemployment has remained steady at 7.3% over the past 6 months. Industry Statistics The FRB recently revised its index of industrial production and changed the base year from 1967 to 1977,1/ The revised total index shows a 0.1 % higher annual growth rate between 1967 and 1984 than the previous index. In the slower growing or declining industries, such as metal mining, primary metals, and fabricated metals, however, downward revisions in the indices and rates of growth have occurred. The previous and revised annual rates of growth between 1977 and 1984 for several of the sectors of interest to the mining industry are shown in table 2.

Jan 1, 1985

By Walter R. Storms

This paper , which describes the mining methods and costs at the Atwood copper mine in the Lordsburg ( Virginia ) Mining District of Hidalgo County , N. Mex . , is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices , methods , and costs in various mining districts of the United States . The mine and surface plant are situated in the west half of sec . 7 , T. 23 S. , R. 18 W. , about 3 miles by road southwest of the center of Lordsburg , near the old abandoned townsite of Valedon ( see fig . 1 ) . The main line of the Southern Pacific Railroad passes through Lordsburg , as does the paved eastwest U. S. Highway 70-80 . A spur line of the Southern Pacific ends near the mine . A good graded road connects the mine with Lordsburg . The following pages present a brief history of the district , describe the geology , and outline methods of prospecting and exploration, including sampling and estimations of tonnages and values . Development, and mining methods are explained , and transportation , ventilation , drainage ,. safety measures , and organization are described . The wage scale and costs of development and mining comprise the corrcluding sections of this circular .

May 1, 1949

By J. D. Davis

Coke Since the beginning of manufacturing of metallurgical coke in the United States, which dates from about 1859, Pennsylvania has main tamed supremacy in coke production Available statistics for the year 1880 show an output of 3,338,300 short tons, which was neatly trebled by the end of the succeeding 10 years. From this time on the increase was steady, though not rapid, and in 1922 the total production was 13,991,892 tons, which is approximately 37 per cent of the total coke production of the United States. The main reason for the rapid development of the coke industry in Pennsylvania lies in the abundance of coals particularly adapted to beehive coking, for which purpose the Pittsburgh bed in the Connellsville district has long been looked upon as standard At first practically all metallurgical coke was made in beehive ovens, the only exception being the short lived and wasteful method of coking in piles, byproduct owns did not make then appearance until after 1893 The suitability of a beehive coking coal cannot be accurately predicted from its chemical analysis, but it can be said, perhaps, that the volatile matter should be about 32 per cent, and that the oxygen content should not be mole than 10 pet cent or less than 4 per cent The sulphur and phosphorus content should be small-not over 1 25 per cent sulphur and under 0 02 pen cent phosphorus-and the ash content should not be over 7 per cent The Pittsburgh bed at Connellsvnlle fills these requirements well, as may be seen from the following representative analysis. Analysts of coal from Pittsburgh bed Moisture 1 70 Volatile matter 31 10 Fixed carbon 59 80 Ash 7 40 Sulphur 0 85 B t u 13,990

Jan 1, 1928

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By E. D. Gardner

"The town of Ajo is built in the desert and consisted of but a few houses when the New Cornelia Copper Co. started operations. Since there were no stores at Ajo or vicinity the New Cornelia Cooperative Mercantile Co. was established to serve the needs of the employees of the New Cornelia and allied companies.The New Cornelia Copper Co. advanced the money to erect the store building and to buy the stock, and assumes all risks. In all, $85,000 has been advanced, representing the capital stock of the enterprise.The store is run by a store manager appointed by the Copper Company and who reports only to the general superintendent. A committee of seven workmen, representing the various depart¬ments, meet with the store manager monthly and make suggestions for the betterment of the service and, present complaints which have been brought to their attention.The store is well managed, carries a large and well assorted stock and is modern in every respect. Prices are at the same level as in the other Southwestern mining camps. The Copper Company does not particpate in the profits of the store but does receive six per cent interest on the capital advanced. At the end of the year, after making proper deductions for interest on capital account, depreciation of store equipment and fixtures, and, for a proper sum to the surplus account, the rest of the profits is distributed among the employees of the company in proportion to the amount of their purchases."

Aug 1, 1920

By Kenneth M. Maas

The U.S. Bureau of Mines began a five-year study of the 7.0 million acre Ketchikan Mining District during 1990. This study is part of the Bureau's ongoing statewide mining district evaluation program. The study area was subdivided and then prioritized by mineral potential into work units. Bureau field work in 1990 focused on the southern portion of Prince of Wales Island and vicinity. Extensive mineral resources have been mined historically in the area and are presently being evaluated by private industry. Information in this report is based on an extensive literature search and Bureau field work. Over 150 mines, prospects, and mineral occurrences were visited in 1990; an aggregate of 1,300 rock, placer, and limestone samples were taken; and nearly 3 miles of underground workings were mapped. Many prospects, some untouched for more than 80 years, were mapped and sampled. High metal values at several prospects were confirmed by Bureau sampling. Reconnaissance sampling along logging roads on Southern Prince of Wales Island revealed mineralized areas not previously recorded. Follow-up work at many locations is planned for the 1991 season.

Jan 1, 2011

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

The coal-bearing areas of Kansas cover approximately 18,800 square miles (23 percent of the state's total area). Coal in Kansas ranges from lignite to high volatile bituminous, located principally in the south-eastern part of the state. Kansas reserves are estimated to be 987,500,000 tons, approximately 0.2 percent of U.S. reserves. Coal beds generally occur in thin seams up to five feet thick. The overburden-to-coal stripping ratios in Kansas are among the highest in the nation, typically 20 to 1, with some ratios up to 35 to 1. The first commercial coal mining operation in Kansas opened in 1865 at Fort Scott in Bourbon County. As in other states, coal production in Kansas increased during the industrial revolution, and then fell as industry converted to alternative fuels. Production peaked in 1916 and 1917, with annual production of 7,250,000 tons. Coal production today is by surface mining methods. The Kansas regulatory program was approved April 14, 1982; the Abandoned Mine Land Program was approved February 1, 1982; and the emergency program authority was approved January 10,1989.

Jan 1, 1992

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Ronald T. Mayerle

In-1992, the U.S. Bureau of Mines conducted a mineral investigation of the Anderson Mountain study area, including RARE II area 4-942, in Lemhi County, Idaho. The 7,340-ha study area lies within the Salmon National Forest about one kilometer north of the old mining town of Gibbonsville (pop.: 100). The eastern boundary of the study area is formed by the crest of the Bitterroot Range. The crest also serves as the continental Divide, and as the border between Idaho and Montana. The study area lies within the Gibbonsville Mining District, an important past producer of gold from lode and placer deposits. Since the 1870's, several hundred claims for both types have been located in the study area. Thirty-six current (1992) lode claims and two patented claim groups (one lode and one placer) are wholly or partially in the study area. No placer claims are current. In all, twenty-seven lode and five placer properties in and adjacent to the study area were investigated. Workings on the properties included 2 caved shafts; 36 caved adits; 8 open adits; 120 small pits, cuts, and trenches; and 4 large dozed cuts.

Jan 1, 1993

By E. D. Gardner

Humphreys Gold Corporation of Denver, Colo., was conducting a successful placer operation in 1936 on North Clear Creek about 6 miles below Blackhawk in Gilpin County, Colo. About 3,000 cubic yards of gold-bearing gravel are dug daily (September. 1936) by two draglines and a power shovel. The gravel is screened in a portable washing plant; the trommel oversize is discarded, and the undersize is pumped to a gold-saving plant. The gold is caught in riffles in sluice boxes. The total cost of mining is about 20 cents per cubic yard. The mine is in a narrow canyon at an altitude of 7,200 feet. The Blackhawk-Central City branch of the Colorado & Southern RR. runs over the property. Freight platforms for receiving supplies were moved as the workings advanced. The workmen reached the mine on a speeder that ran on the railroad tracks from a point on the automobile highway (U. S. 40) on Clear Creek near the bottom of Floyd Hill, about 5 miles distant. The mine is 36 miles by road and speeder, or 30 miles by rail, from Denver.

Jan 1, 1937

By L. Garner McDonald

The U.S. Bureau of Mines tangentially impacted potential coal-cutter bit shank materials against sandstone to investigate the potential of the materials to ignite natural gas by a friction-generated hot streak. The shank material samples were mounted in a 24-in, 550-lb flywheel, which was rotated at surface speeds of 400 to 900 sfpm. The sandstone was advanced toward the rotating flywheel at feed rates of 1 mil per impact. The atmosphere mixture was 7 vol pct natural gas in air. Three grades of polycarbonate resin, an ultra-high-molecular weight polyethylene, and a zinc alloy (ZA27) were among the potential materials. None of these materials caused ignition of the methane at any of the three test speeds (400, 600, and 900 sfpm), but the above materials do not have sufficient strength to hold a carbide tip during coal cutting. Of the materials having sufficient strength to hold a carbide tip, three nickel-based alloys proved less likely to cause a natural gas ignition than did iron-based alloys such as 4340 (a commonly used shank material for coal cutters).

Jan 1, 2010

By L. Garner McDonald

The U.S. Bureau of Mines tangentially impacted potential coal-cutter bit shank materials against sandstone to investigate the potential of the materials to ignite natural gas by a friction-generated hot streak. The shank material samples were mounted in a 24-in, 550-lb flywheel, which was rotated at surface speeds of 400 to 900 sfpm. The sandstone was advanced toward the rotating flywheel at feed rates of 1 mil per impact. The atmosphere mixture was 7 vol pet natural gas in air. Three grades of polycarbonate resin, an ultra-high-molecular weight polyethylene, and a zinc alloy (ZA27) were among the potential materials. None of these materials caused ignition of the methane at any of the three test speeds (400, 600, and 900 sfpm), but the above materials do not have sufficient strength to hold a carbide tip during coal cutting. Of the materials having sufficient strength to hold a carbide tip, three nickel-based alloys proved less likely to cause a natural gas ignition than did iron-based alloys such as 4340 (a commonly used shank material for coal cutters).

Jan 1, 1992

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010