Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

By James A. Finch, Robert E. McIvor

"This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.INITIAL DEVELOPMENT OF THE CIRCUIT MODELThe Functional Performance Equation for Closed Circuit Ball (or Pebble) MillingIt has been shown that closed grinding circuit performance can be effectively characterized by the “functional performance equation” for closed ball or pebble milling circuits (McIvor, 2006a). One method of its derivation is summarized here for convenient reference.First select a cut-off size to define “coarse” versus “fine” or product size material for the grinding circuit. Any particle mesh size can be used to differentiate between coarse material and fines, but the circuit target P80 is often an effective choice for these purposes.Any energy expended on “fines” is wasted. It also generates “extreme fines” often detrimental to downstream processing (McIvor and Finch, 1991). Only the portion of the mill power draw that is expended on coarse material is effectively used. This portion can be estimated from the mill feed and discharge size distributions (McIvor, 1988a) by taking the average of the percentage of “coarse” material in the mill feed and discharge. We can define the thusly calculated percentage of the mill power that is expended on coarse material in the mill as the ball mill circuit “classification system efficiency” (CSEff). The “effective mill power” (EMP) can be calculated from the total mill power (TMP) as follows."

Jan 1, 2007

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By Serena Biella

Gold has received a growing interest as a catalyst for the selective oxidation of organic molecules using oxygen under mild conditions1. In the liquid phase application small gold particles (2.5-7 nm) deposited over different solid supports can be used but, like many other noble metals, their catalytic activity depends upon the nature of the support and the preparation metod2-5. In particular, gold on carbon is the preferred catalyst for the oxidation of the alcoholic 2-7 and the aldehydic7-9 groups and one of the best preparation method is the immobilisation of colloidal particles2-5,8,9. Suggested application of gold catalysis in fine chemicals production, tested on laboratory scale preparations, is reported in table 110. In order to produce more efficient catalysts for the liquid phase oxidation and to derive new insights into the reaction mechanism, we have made a comparison among catalytic systems based on different metals. The first effort was to test the activity, if present, of naked metal particles and then to study the influence of various materials commonly used as a support.

Oct 1, 2003

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By L. A. Melis, K. S. Fraser

"This paper describes the development of a milling circuit for the complex Midwest orebody, containing a high-arsenic uranium ore typical of that found in northern Saskatchewan. The results of preliminary bench-scale test work are summarized. Data from a pilot-plant program carried out at the Ontario Research Foundation are provided for the selected mill flowsheet. Also described are waste circuits which have been established to produce effluents of acceptable quality. Pilot-plant testing of sub-aerial tailings deposition is also described. The applicability of manufacturers' equipment for the various circuits in the flowsheet is discussed.IntroductionThe Midwest uranium deposit is in northern Saskatchewan, 700 km north of Saskatoon, near the eastern edge of the Athabasca BasinDevelopment work on the project is directed by Canada Wide Mines Ltd., a subsidiary of Esso Resources Canada Limited. Participants in the project are Esso Resources Canada Limited, Numac Oil and Gas Ltd., Bow Valley Industries Ltd ., Mink Mining Corporation and Midwest Mining Corporation.The deposit consists of a series of flat lenses of massive ore overlain by a halo of lower-grade sandstone ore. The massive ore is formed of pitchblende and nickel arsenides, along with clay, and averages about 10% U and 9% Ni, The principal minerals are pitchblende (UO2-UO3), coffinite (U(SiO4)1-x(OH)4x), gersdorffite (NiAsS), niccolite (NiAs) and rammelsbergite (NiAs2). The sandstone ore, a friable clay-rich sandstone with sooty pitchblende, averages about 0.4% U and 0.6% Ni. Typical expected mill feed analyses are given in Table I.A bench-scale development program ore was carried out during the period from August 1978 to May 1981 in the laboratories of Lakefield Research of Canada Ltd. (Lakefield), (Lakefield, Ontario), the Colorado School of Mines Research Institute (CSMRI), (Golden, Colorado) and, to a lesser extent, the Ontario Research Foundation (ORF), (Mississauga, Ontario) and the Saskatchewan Research Council (SRC), (Saskatoon, Saskatchewan). Direction of the development studies was shared by Canada Wide Mines Ltd. and its metallurgical consultants, A.H. Ross and Associates. Input was received from Envirotech, Enviroclear, Interox America, and Knight and Piesold Ltd."

Jan 1, 1983

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By Wayne Phillips, Anatalia Silva, Robert Henderson, Tondo. Luis

"Kinross’ Paracatu Mine has 20 years of operational success as one of the lowest grade milloperated gold mines in the world. At year end 2005, Paracatu’s Proven and Probable Reserves were 1.18 billion tonnes at a grade of 0.40 g/t Au, containing a total of 15.2 million ounces of gold.In 2005, the plant processed 17 Mt of ore and produced 180,519 ounces of gold at a cash cost of US$274/oz. An investment of US$470 million has been approved to expand production to 61 Mtpa in 2009 which will extend mine life to 2036. During the period from 2009 to 2013 the project is expected to produce an average annual output of approximately 557,000 ounces of gold at an average cost of sales of approximately $230 per ounce.The soft, friable ore containing readily leachable gold associated with sulphides lends itself to simple processing. The process flowsheet consists of crushing, grinding, gravity recovery, flotation, concentrate leach and carbon adsorption to produce bullion bars. This paper describes the current operation, the deposit’s unique metallurgical features and the future expansion plant that has been designed to optimise recovery of gold.INTRODUCTIONRio Paracatu Mineração (RPM), a wholly owned subsidiary of Kinross Gold Corporation, operates the Paracatu mine. The mine is located in Brazil, 230 km south west of Brasilia in the north west portion of the State of Minas Gerais. The city of Paracatu, which has a population of 83,000 people, is just 2 km south of the mine."

Jan 1, 2007

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By Bjarne Ekberg

"The most economical way of dewatering mineral concentrates is to reduce the moisture content in the material mechanically using thickeners and filtration avoiding thermal drying whenever possible. In addition to this, the dewatering process should produce low moisture cake, high quality liquid, consume little energy. As a part of the dewatering process The CERAMEC® capillary filter has been proven to meet these requirements in over 150 installations. The filtration is done by using ceramic filter plates with small pore size. The capillary action in the filter medium secures gas free filtration at good vacuum, and due to the small pore size, filtrate is crystal clean and particle free. The energy consumption is minimal. This paper will discuss results from filters installed at Pyhäsalmi Mine Oy in Finland where the technology was has been used since the late eighties. Results from more recent installations like Los Pelambres in Chile and LKAB in Sweden will also be discussed.INTRODUCTIONThe idea of using capillary action to make dewatering more efficient was invented two decades ago. Ten years later whole filter plants utilizing the new method were delivered to mine concentrators for dewatering of mineral concentrates. Further development of ceramic membrane plates made it possible to meet the requirements in iron ore dewatering. In addition to low cake moisture, high capacity and low energy consumption, there are a lot of environmental advantages in using capillary filtration. One of them is clear filtrate.CAPILLARY FILTRATIONA micro-porous filter material behaves like a large number of narrow capillaries forming a network. When a pressure difference ?P is applied over the wetted, hydrophilic pore with the radius r, the force striving to push the water out of the pore will be ?Ppr2. The force striving to hold the water in the pore will be the vector force 2pr? cosa of the surface tension ? and the cosine contact angle a. Equalling those forces and solving the equation for ?P we get"

Jan 1, 2003

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996

By E. M. Watkin

"Although Canada has achieved one of the highest living standards in the world, people and organizations have, over the past decade, begun to question the cost and means of this achievement. Concern has been expressed about the degree of environmental disturbance arising from industrial activities which have greatly contributed to our increased living standards. These industries include hardrock mining, pit and quarry operations, hydro-electric schemes, various agricultural enterprises and urban land developments.In the construction and operation of the above industries many environmental problems arise because the natural vegetative land cover is destroyed or drastically disturbed. Disturbance may occur to such a degree that revegetation is di ffi cult, often it appears impossible. Portions of the environment around such industries remain aesthetically unacceptable and appear to offer little or no potential for future resource use in wildlife, recreation or agriculture.The general public cannot dissociate itself from the activities of the aforementioned industries. It has, over many years, accepted the benefits and conveniences arising from those activities. Despite this, the increasing level of public concern imposes upon industry a need to alleviate or repair past, present and future environmental disturbance. Therefore it is incumbent upon industry to modify present technology or develop new techniques which would allow the disturbed environment to be easily and rapidly repaired."

Jan 1, 1975