Search Documents

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By Mari Yamamoto

Controlled thermolysis of gold(I) complex, [Au(C13H27COO)(PPh3)], at 180 °C for 5 h under an N2 atmosphere affords the new type of monodispersed spherical gold nanoparticles capped by myristate and a small amount of PPh3 ligands (average diameter 23±1.5 nm), in spite of no use of solvent, reducing agent and stabilizer. Much attention has been paid to the preparation and structure determination of transition metal nanoparticles, because of their widespread use in technological applications.1 In general, the chemical reduction of metal salts and organometallic complexes2 by the use of reducing agent is carried out to prepare gold nanoparticles. In some cases, a large amount of solvent and stabilizers such as surfactants,3 polymers4 and ligands5 are used to prevent agglomeration of particles and control the particle size. For instance, Brust et al. reported a two-phase reduction of AuCl4 - by NaBH4 in the presence of dodecanethiol as stabilizer to prepare gold nanoparticles.6 On the other hand, O?Brien et al. recently reported an one-phase preparation of gold nanoparticles by the reduction of AuCl4 - by NaBH4 in the mixture of tri-n-octylphosphine oxide and octadecylamine which act as both solvent and stabilizer, but this procedure also needs reducing agent.7

Oct 1, 2003

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015

By A. Mykytiuk, I. E. Puddington, W. D. Macleod, F. W. Meadus

"A laboratory-scale continuous procedure for the up-grading of naturally occurring tin ores, based on the principle of spherical agglomeration, is described. High recoveries are indicated. A proposed second stage suggests useful fractionation steps.IntroductionA LABORATORY-SCALE batch process for the upgrading of a tin ore using the principles of spherical agglomeration has already been described (1). This procedure consisted of milling, for about an hour, a precrushed ore with at least 200 per cent water, 0.2 per cent of a reagent such as tall oil (to render the de-sired ore particles hydrophobic) and about 3 per cent of a viscous petroleum oil. The feed material passed an 8-mesh Tyler sieve, and the percentages of re-agents are based on the dry weight of the feed. Du-ring the grinding, the hydrophobic particles transfer into the oil phase to produce coherent semi-solid bodies while the gangue stays preferentially in the aqueous phase. The concentrate can be separated from the gangue easily by a mechanical operation. Using an ore containing about 0.3 -0.5 per cent tin, grades of from 1.5 to 7.0 per cent were obtained by varying the pH of the system. Recoveries fell from about 80 per cent to as low as 50 per cent as the grade in-creased."

Jan 1, 1966

By W. Torres Pino, L. Mariscal Samaniego

The Ilo Smelter has been continuously operating since 1960 with Reverberatory furnaces and Pierce Smith converters producing blister copper. The original installed capacity of 1.134 tons per day of concentrated was expanded in 1976. A process of modernization started in 1995 and 1998 with the installation of an El Teniente Converter, a sulfuric acid plant and an oxygen plant to reduce the gaseous emissions to the atmosphere. With the official approval of the Environmental Compliance and Management Program (Programa de Adecuaci6n y Manejo Ambiental - PAMA) in January 1997, Southern Peru Copper Corporation made a commitment to capture 91. 7% of the S02 generated at the smelter by January 2007. After an evaluation of six different technologies, the ISASMEL T process was selected because it can be easily adapted to the present operation, has a lower capital cost and it is a simple process. The fast learning curve to reach the total capacity will allow to fulfill the PAMA commitment in time. The project construction is in process and SPCC is prepared for a successful start-up and transition of the current operations at the end of year 2006. This paper outlines the factors considered by SPCC in its choice of ISASMEL T technology and describes the construction and the start-up activities of the new facilities.

Jan 1, 2007

By Gino Palarchio

Dofasco is Canada?s 2nd largest steel manufacturer producing 4.5 million tons of flat rolled steel per year. They have revenues of over $3 billion and employ 7,000 people in their Hamilton, ON plant. Dofasco is North America?s most profitable steel producer and were recently ranked as the #1 steel maker in the world by Dow Jones. Motivation to Improve In the 1980?s the steel business was good. However, in the late 80?s and early 90?s things began to change. Globalization was beginning to influence the market, imports started arriving at lower prices and higher quality, hangover from the 1970?s inflation saw costs rising and prices dropping, there was a shift from a sellers to a buyers market, and shareholder returns were beginning to erode. Dofasco took a step back and evaluated their maintenance performance and found that they were operating in an environment where 70% of their work was reactive and only 30% was proactive. They also found that the rate of product quality improvement was flat and their average equipment availability was only 78%. At that point they realized that Equipment Reliability was key to improving product quality, production output, costs and shareholder return. They initiated a project to research, develop, and implement the most advanced maintenance practices and information technologies to achieve maximum equipment reliability.

May 1, 2001

By Guohong Yin

Oxidized sulfidic tailings contain significant amounts of accumulated acidity in the form of water-soluble secondary sulfate minerals and thus constitute long-term sources of acid drainage at many metal mining sites. As part of site remediation activities, alkaline amendments are often added to the oxidized tailings to increase the pH and immobilize the metals. This study assessed the advantages and limitations of using lime mud, a byproduct of Kraft pulp mills rich in calcium carbonate (> 90 wt. %), as alkaline amendment. The inorganic and organic constituents of lime mud samples were quantified. Leachable impurities were determined by the TCLP method. The performance of lime mud was compared to that of reagent grade quicklime (CaO) and calcite (CaCO3). Tailings treated with lime mud or calcite have strong buffering capacities and remain at neutral pH conditions (pH ~ 6.7) for long times. In contrast, tailings treated with quicklime have a very low buffering capacity, and their pH decreases with time. Furthermore, lime mud has finer particle sizes and thus a greater specific surface area than most forms of commercially available calcite, which results in enhanced reactivity. Dissolved metal concentrations are similar in tailings slurries treated with lime mud or calcite. This study suggests that lime mud is an environmentally and economically attractive alkaline amendment for oxidized mine tailings.

Nov 1, 2002

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By Earl M. Frizzell, Joseph A. Dos Santos

"Conventional belt conveyors offer an economical method for transporting materials at inclines approaching 18 degrees. Sandwich belt conveyors may be used to transport materials at high angles, to 90 degrees, while maintaining the most positive features of conventional conveyors, that is, (1) proven conventional conveyor components. (2) high-speed operation, (3) high-single lifts, (4) continuous cleaning of the smooth surf aced belts, and (5) easy, quick repair by hot or cold vulcanizing. The present discussion deals with the evolution and development of sandwich belt conveyors to satisfy the operational requirements of the open-pit mining and materials-handling industries.A look at the limitation s of conventional shallow angle conveyors reveals the conveying angle at which a cover belt is needed. The relationship between conveying angle and hugging pressure by the cover belt is developed mathematically. A study of past and current developments reveals that the Loop Belt and Beltavator are significant advances in the state-of -the- art. The vertical radius of curvature constraints are discussed in detail and the constraint equations are developed. Criteria for future development is established as a basis for evolutionary developments in sandwich belt high-angle conveyors. The use of intermediate drives in sandwich belt high-angle conveyors is investigated.IntroductionIn connection with U.S. Bureau of Mines funded–study relating to continuous haulage from deep open-pit mines, the authors had occasion to study extensively, the use of high-angle conveyors as a means of hauling mine products continuously from the pit while maintaining optimum mine slopes to minimize total excavation. The many possible high-angle conveying methods investigated included skip hoists, bucket ladders, pocket belts, fin belts, cleated belts, sandwich belts, pipe belts, screw conveyors, slurry pipe lines, and others. The sandwich belt high-angle conveyor appeared to be the most operationally-appropriate and economical solution for the mining industry. The present paper presents the theory, historical development, state-of-the-art, and evolutionary developments in sandwich belt high-angle conveyors."

Jan 1, 1983

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

By Desmond M. Levins

"Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s.Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. IntroductionAustralia is entering a new phase in uranium mining and milling activity . In the first phase of operations, between 1954 and 1971, about 10,000 tonnes of yellowcake was produced at five locations. Most of the production came from the mines at Rum Jungle in the Northern Territory and Mary Kathleen in Queensland. In the 1960s, the demand for uranium slumped, and much of the yellowcake produced at Rum Jungle was stockpiled by the Australian Atomic Energy Commission. The early uranium processing operations in Australia were typical of overseas practice at that time. Environmental problems were generally given low priority and pollution control measures were unacceptable by today's standards. There was little or no recycling of process water, acid waste streams were not neutralized and tailings dams were poorly designed. At Rum Jungle, oxidation of sulphides in waste heaps, tailings dumps and ore stockpiles subsequently led to destruction of vegetation and heavy metal pollution in a nearby river.In the early 1970s, major uranium deposits were discovered in the Alligator Rivers region of the Northern Territory. Significant orebodies were also located in the Great Artesian Basin in South Australia, in calcrete formations in Western Australia and at several locations in Northern Queensland. According to latest available estimates. Australia has about 160/0 of the Western World's uranium recoverable below $US 80 per kg U. Mining these orebodies will require pollution control measures more stringent than practised previously in Australia."

Jan 1, 1980

By D. C. Fuller

"CoaLiquid, Inc. (CLI) has been in the coal-oil-mixture (COM) business for over five years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August 1979. For over two years CLI has been expanding its efforts and conducting large-scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit.CoaLiquid has conducted commercial-scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.IntroductionCoaLiquid, Inc. officially dedicated its plant on August 31, 1979, at a ceremony presided over by the then Governor of Kentucky, The Honorable Julian Carroll. The dedication marked the culmination of over three years of research and development work and marked the beginning of a new era of coal-oil-mixtures as a commercial commodity in the marketplace. As the first such plant in the United States, it set the tone for construction to follow.CLI was originally owned and managed by a group of entrepreneurs from Kentucky who had developed the process and constructed the plant on purely private investment and conventional financing. Beginning in late 1976, with a pilot-scale operation, also located in Shelbyville, Kentucky (near Louisville), CLI began producing a stable mixture of 50070 coal, 30% to 40% oil and 10% to 20% water by weight. The technology employed was developed by Eric C. Cottell of Long Island, New York and is covered by U.S. Letters Patent No. 3,941,552. Since the pilot plant operation, CoaLiquid has made many refinements to its process and in fact has added new technology to its portfolio of patents and patents pending. Further refinements to the product now produce a stable mixture of 50% coal, 40% No.6 fuel oil and 10% water by weight."

Jan 1, 1985

By Robert Macdonald, William Coombe, John F. Lewry

Gold occurrences have been known in the La Ronge Domain for many year . Mineable reserves have more recently been outlined and there is every prospect of a major gold camp being established in the domain within this decade. The La Ronge Domain lies in the Lower Proterozoic 'Trans-Hudson Orogen' and is part of a collage of Early Proterozoic crust comprising volcanoplutonic arcs, batholiths, associated volcaniclastics and volcanogenic sediments lying between the Superior Craton to the outheast and the reworked Archean basement/Aphebian cover terrain to the northwest. The domain has several lithostructural subdivisions, the most important of whjch , from a gold exploration point of view, is the Central Metavolcanic Belt. This belt is composed dominantly of a range of metavolcanic rocks and gabbroic to granitic intrusives, which geochemically resemble younger subduction-generated 'primitive' arcs developed on oceanic crust. U-Pb zircon geochronology indicates that the arc volcarusm and pre- to late-kjnematic plutonism occurred about 1890 Ma to 1850 Ma ago. The belt has an attained grade of upper greenschist to amphibolite facies and is relatively undeformed , though high strain zones occur locally. Most gold occurrences in the La Ronge Domain have been found in the Star-Waddy Lakes area of the Central Metavolcanic Belt, and in the Sulprude-MacKay Lakes area to the south which is interpreted as a tectonically dismembered part of the main belt. Both tratiformand vein-type gold occurrences are present in the domain; vein-type predominate and form nearly 90 per cent of the occurrences. The stratiform-type occurrences show a regional lithological a sociation with iron-rich sediments within proximal felsic volcanjc sequences. Some vein-type occurrences appear related to brittle fracturing associated with intrusive emplacement (the magmatic-hydrothermal "syn:' and "subvolcanic" veins) and faulting. However, most of the vein-type occurrences exhibit a spatial association with regionalscale ductile shear and other high strain zones, and were probably formed by metamorphichydrothermal processes.

Jan 1, 1986