Search Documents

By I Basson, J A. Miller, M Becker, F C. de Beer, L C. Bam

"Geometallurgy brings together geologists, mine planners and process engineers to extract meaningful mineralogical and textural information from an orebody, with a view to predicting its metallurgical response. Preferably, automated analytical techniques, which provide mineralogical and textural information, should process a large number of samples quickly, relatively inexpensively and reliably. Microfocus X-ray computed tomography (µXCT) is capable of producing 3D volumetric information on texture and mineralogy that satisfies some of these criteria. µXCT has been used extensively to study the porosity and internal pore structure of iron ore pellets as part of downstream processing. It has not been widely applied to earlier mineralogical and textural analysis of unprocessed ore, due to the limited ability of X-rays to penetrate high-density samples. In this contribution, we propose scanning methods to overcome this limitation, thereby facilitating a broader application of µXCT to iron ore resource management.CITATION:Bam, L C, Miller, J A, Becker, M, De Beer, F C and Basson, I, 2016. X-ray Computed Tomography – Determination of Rapid Scanning Parameters for Geometallurgical Analysis of Iron Ore, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 209–220 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Berryman, C Adams, L Griesel, C Buxton

The Kalgoorlie Consolidated Gold Mines (KCGM) schedule model is used for short- to medium-term planning and scheduling at the Fimiston Open Pit Mine (the Superpit). The model bridges the gap between grade control models, which are generated one to seven days prior to mining, and the annual Resource and Reserve model update that is used for budget and life-of-mine plans. The schedule model uses close-spaced grade control data (up to 20 000 m drilled each month) as well as resource definition drilling to estimate production volumes three to six months ahead of current mining. From this, a rolling 12 week mining and processing schedule is generated on a monthly basis. As the KCGM operation is mill and sulfur constrained, the schedule model needs to be an accurate predictor of ounces as well as tonnes, gold and sulfur grades. The process must also be time efficient in order to meet monthly planning and reporting deadlines. Due to the large amount of new data generated each month, model updates using conventional interpretation and estimation techniques have proven to be impractical and too time consuming. This paper will examine the evolution of the Superpit schedule model process over time, recent improvements and the effect of different model outcomes on short- and medium-term mine planning.CITATION:Griesel, L, Buxton, C, Adams, C and Berryman, T, 2014. The superpit schedule model – A time-efficient data-driven estimation for short- and medium-term planning, in Proceedings Ninth International Mining Geology Conference 2014 , pp 397–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A L. Zawadski, B G. Putland

"This paper discusses a method to build a calibrated comminution circuit model, using historic operating data and blend information that is useful for forecasting and optimising plant performance, as well as evaluating expansion opportunities. A preferred method for building a calibrated power-based comminution model is discussed and justified based on two case studies, offering low-cost and effective strategies to utilise existing information for the maximum possible benefit.The first example is the Lefa Gold Mine located in Guinea, West Africa operating a semi-autogenous grinding (SAG) and ball milling circuit with recycle crushing (SABC). Daily blend information and operating data was utilised to build and calibrate a power-based model of the comminution circuit. The least squares regression method was used to solve the SAG mill specific energy requirement and the operating work index (Wio) for each individual ore type. The calibrated model was used to evaluate expansion strategies to sustain throughput at higher proportions of fresh ore based on the proposed life-of-mine schedule.The second example is the Ok Tedi Copper-Gold Mine in Papua New Guinea operating a SAG and ball milling circuit (SAB). The circuit limitation would often shift between the SAG mill and the ball mill due to variable ore characteristics and feed blend. Typical SAG mill relief strategies, such as recycle crushing or secondary crushing, required significant capital expenditure and the potential throughput benefit would vary depending on ore type, making economic justification difficult. Daily blend information and operating data was used to build and calibrate a power-based model of the comminution circuit to identify ore types that might benefit from higher blast intensities to increase fines content, thus relieving the SAG mill limitation and increasing overall throughput without a major capital investment.Citation:Zawadski, A L and Putland, B G, 2016. Calibrating Comminution Models Using Operating Data to Forecast and Optimise Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 17–26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By H J. Dalstra

High-grade iron ore may be derived from banded iron formation (BIF) through four fundamentally different processes:1. syngenetic precipitation of chert free BIF,2. residual enrichment by removal of gangue minerals from BIF to form bedded (residual) ironore,3. mechanical erosion of iron oxide and chert from bedded iron ore or BIF and re-deposition andupgrading as detrital iron ore, and4. chemical removal of iron from BIF and precipitation elsewhere as a secondary (channel) irondeposit.Finally, the BIF itself may constitute iron ore if a high-grade concentrate utilised for pellets or sinters can be derived from it through mechanical (industrial) separation of iron oxide by means of crushing/milling and mineral separation.Historically, exploration for high-grade BIF hosted iron ores was focused on the residual (bedded) deposits and driven by supergene concepts. Exploration for detrital and channel type iron ores was mostly secondary to exploration for bedded deposits, but recently, a more focused exploration effort has led to the discovery of enormous moderate to low iron grade deposits in the Pilbara region of Western Australia. Exploration for high-grade iron ores using syngenetic concepts has been limited,but together with exploration using hypogene concepts offers the best hope of fi nding concealed deposits. Exploration for BIF sources suitable for concentrate ores commenced in the ‘old’ iron ore provinces after the high-grade resources were depleted and has only recently gained importance in Australian BIF provinces, mainly as a result of high iron ore prices in the last decade.

Jul 11, 2011

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By E Mare

Recent highly publicised incidences of disastrous containment failures, none more pertinent than the 2019 iron ore tailings dam failure in Brumadinho, have focused the world’s attention squarely on the often-challenging subject of tailings storage. Unwanted ultrafines, that are deemed to be unworthy of further treatment or not to have further saleable value, are therefore a significant issue for mine owners looking to reduce risks and perceptions associated with long-term storage of tailings. In this context, there are strong drivers to identify safer approaches to ultrafine tailings management, especially if it can also lead to increased revenue, together with better water stewardship and environmental outcomes. The better management of tailings needs to be considered from both containment challenge and processing opportunity perspectives. This paper focuses on the latter, reviewing from a technical and economic perspective, the feasibility of more extensive processing and/or reprocessing of specifically iron ore tailings, in a bid to reduce the overall volume for management in long-term storage. Herein the opportunity lies in recovery processing, as much as enhanced thickening and/or mechanical dewatering, and therefore the paper discusses both issues as equally important sides of the same coin. Recent interest in iron ore ultrafines processing and reprocessing studies suggests that the enhanced processing of iron ore tailings offers multiple perceived advantages. Apart from a potential reduction in tailings volume, associated with safer containment, lower environmental impact and improved water management, the prospect of increased revenue from additional Fe recovery presents supplementary motivation for iron ore players to embrace this approach, as further elaborated in this paper.

Nov 8, 2021

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L Semenyna, W Douglas

Gold is often present in solid solution with pyrite in the Carlin Trend. The presence of organic carbon along with gold hosted in sulfide, referred to as double refractory ore, requires that ore with high carbon-in-leach (CIL) preg-robbing potential and poor leach recovery is routed to a roaster. During roasting, the pyrite is oxidised to (ideally) form hematite (Fe2O3), and the gold that was present as solid solution in the pyrite forms colloids within the hematite. The ideal texture of the produced hematite is porous to allow for the penetration of cyanide for gold dissolution. Temperature and other conditions of roasting, as well as ore characteristics (pyrite mineral associations, arsenic) can affect the texture and the type of iron oxide formed. Many of these alternate iron oxide minerals result in incomplete leaching. Comprehensive gold deportment studies have proven that the majority of the gold losses in Barrick GoldstrikeÆs roaster leach tailings occur within the iron oxides created through the roasting process.The iron oxide phase that hosts the majority of the gold in tailings is in the form of by-product maghemite (?Fe2O3), which is highly magnetic. Barrick Goldstrike has designed a magnetic recovery circuit to capture these iron oxides, and with subsequent reprocessing, recover the lost gold. Pilot plant results and analysis using scanning electron microscope mineral liberation analyser (SEM MLA) shows that up to 30 per cent of the gold in tailings can be recovered with a three per cent overall mass pull to magnetic concentrate. This magnetic concentrate can be economically reprocessed, resulting in a three per cent improvement in roaster recovery.CITATION:Douglas, W and Semenyna, L, 2013. Magnetic recovery of gold-bearing iron oxides at Barrick GoldstrikeÆs roaster, in Proceedings World Gold 2013 , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

By R M. Arellano, D M. W Harney, M Makhuvha

Mineral resource and ore reserve estimates are founded on two sources of data: tonnage and grade. The tonnage is a product of volume and density; both of which are estimates. Density impacts numerous operational factors, which include, but are not limited to, mine design, mine planning, equipment selection and operational performance. Hence, density is a significant parameter and its determination requires similar care as the measurement of grade. Selecting an appropriate method to determine density, and ensuring its rigorous application, thus reduces risk and can improve operational performance, which in turn increases profit margin.Different Anglo American sites use a variety of practices and protocols to determine density, which is highly dependent on the physical characteristics of the orebody, local conditions and historical practices. Also, individual sites sometimes execute the same method in a slightly different way, which may also affect the outcome of the measurements. In order to gain a better understanding of how density is determined at Anglo American projects and operations, a review of these techniques was undertaken. The objective of the study was to identify and share good practices across the company, as well as to look for improvement opportunities, where applicable. Ten different methods of measuring density, applied to nine different commodities, were identified and described. An additional technique was recently developed by Anglo American Technical Solutions. The core pycnometer is a large gas displacement pycnometer capable of measuring density at high accuracy on full pieces of intact core.This paper provides an overview of methods used to determine density within the Anglo American Group, including quality control and quality assurance aspects. It is not the purpose of this paper to identify a preferred method, but to highlight the importance of choosing the best suited practice for a project or mine site. In addition, a case study comparing two different density determination methods applied to the same rock samples from the Los Bronces Copper mine was undertaken and the results of that study are presented here.Selecting the most appropriate method to determine density and comparing results from two or more techniques against each other, together with other suitable quality control procedures, is considered to be of utmost importance for all mining operations and exploration projects.CITATION:Makhuvha, M, Arellano, R M and Harney, D M W, 2014. Determination of bulk density in Anglo American plc, methods and impacts, with a case study from Los Bronces Mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By S Coward, S Jackson, S Moayer, J E. Vann

The variability and uncertainty of mineralisation, coupled with subsequent uncertainty in mining and processing, is often paid scant regard or overlooked during the evaluation of mining projects. In many instances, when the project transitions to the operational phase, the reality of feed or product variability and the consequences of unquantified uncertainties throughout the value chain become obvious. The outcome is the familiar picture of frequent ramp-up underperformance and failure to deliver on planned targets and objectives.Both mine and exploration geologists are expected to generate mineral deposit models that are based on an integration of diverse sources of data. These multifaceted deposit models already play a pivotal role in the design, development and optimisation of mining project value, and the trend to a fully digitally engineered future means that this importance is increasing. It is therefore vitally important that tools be made available to the geologist (as well as mining engineers and metallurgists) that enable them to characterise and assess variability and uncertainty via appropriate deposit models and thus articulate their impact on potential project configurations and decisions. Scenario-based project evaluation (SBPE) provides a framework for full and proper analysis of the downstream impacts of inherent deposit variability and uncertainty on project performance.SBPE has been developed by the authors over several years and aims to propagate geological uncertainty and variability through the mining value chain. The outcomes of SBPE can be tested against future external scenarios capturing financial, economic and socio-political factors that also drive project performance. Stochastic representations of the orebody (via conditional simulation (see Chilès and Delfiner, 1999)) that explicitly incorporate variability and represent uncertainty are propagated through the value chain on a block-by-block basis (ie on a much more granular basis than traditional project evaluation approaches).Conventionally, metallurgical processes are modelled with deterministic equations (eg regression models) based on limited data. The SBPE approach allows for the modelling of process performance uncertainty using geometallurgical sampling fully. Multiple outcomes of SBPE are passed through financial modelling, which can also incorporate stochastic components, thus allowing full quantification of the risks and opportunities of a set of project alternatives. The value of the SBPE system is that once a base case has been established, multiple engineered alternatives coupled with external scenarios are easily evaluated and compared in terms of incremental value.A new case study of SBPE is presented that shows how, by analysis of the various aspects of variability and uncertainty, project managers are able to focus on the areas that have the greatest ability to reduce risk and/or add significant value. This can lead to sufficient flexibility being built into operations that allow operators to cope with the real orebody delivered to the plant.CITATION:Jackson, S, Vann, J E, Coward, S and Moayer, S, 2014. Scenario-based project evaluation – full mineral value chain stochastic simulation to evaluate development and operational alternatives, in Proceedings Ninth International Mining Geology Conference 2014 , pp 21–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P Oikkonen

Sprayed concrete has played an integral role in underground rock support for nearly a century. However, concrete is also considered to be one of the biggest environmental problems in construction and mining, largely because of the high carbon footprint of cement and aggregates production. This is driving the industry to find ways to cut concrete usage where possible. Improving sustainability by cutting concrete material consumption also reduces application time and costs. Improving concrete properties can make it possible to design thinner linings, but as awareness of safety and longer design lifetimes are driving developments in the opposite direction, it is not realistic to see this as a major factor in cutting concrete consumption. More accessible solutions are focusing on layer thickness control and minimising rebound and wastage. Digital technology and innovation offer excellent tools for improving sustainability while optimising other aspects of the spraying process at the same time. A digital layer thickness control system gives near-real-time information to the sprayer operator with full coverage of the sprayed surface. This enables the operator to achieve consistent layer thickness on the first pass, in comparison to the traditional methods of overspraying with the aim of achieving sufficient layer thickness, probe drilling after the concrete has set, and respraying at a later stage if needed. Operator competence is the single biggest variable in a successful sprayed concrete process, affecting rebound and wastage levels. Unfortunately, the learning curve to become a master sprayer is quite steep and training on a real sprayer and real concrete requires a significant amount of time and money. Training in a virtual reality (VR) environment enables operator training to be carried out in a low-risk environment and provides a way of measuring performance and assessing and certifying the operators. After the VR training period, a novice nozzle operator has the basic understanding to start working on a real sprayer, and an experienced nozzle operator can benefit from the possibility of assessing their performance.

Mar 29, 2023

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By F Kock, Y Sulianto, T Trott, B G. Putland, D Morgan

"Northparkes installed and commissioned a secondary crushing circuit in 2010 to debottleneck the semi-autogenous grinding (SAG) mill constrained grinding circuits. Following further improvements to the circuit (inclusion of a double deck vibrating screen), the project successfully delivered finer feed to the SAG mill. The result of this project was an increase in the milled tonnes from 5.6 Mt/a in 2012 to 6.0 Mt/a in 2013.The increased throughput rates introduced new challenges with the circuit becoming power limited. How to best optimise the available comminution power, while delivering the optimal particle size to the flotation circuit was made the key optimisation objective. To achieve this objective, Northparkes initiated a project that included engaging comminution experts. Recommendations included changes to the SAG mill including mill lifter design, increased grinding media charge levels and reduced grinding media size with aim of producing a finer grind size.Northparkes implemented these recommendations along with some other changes to SAG discharge grates and the mill discharge vibrating screen. This achieved a substantial reduction in the flotation feed particle size distribution (approximately 20 microns) by utilising increased average SAG power utilisation, in turn resulting in a two per cent increase in copper recovery.With power utilisation now maximised, the next phase of optimisation has moved to the throughput-grind-recovery relationship and the cost benefit analysis of installing additional grinding power.Citation:Sulianto, Y, Trott, T, Morgan, D, Bell, T, Kock, F and Putland, B, 2016. Optimisation of Installed Mill Power Post-installation of Secondary Crushing Circuit at Northparkes Mines, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 331–338 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024