Search Documents

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

Dry magnet separators are used to upgrade and beneficiate a wide variety of minerals such as hematite and magnetite materials. In recent years advances in dry magnetic separators have improved their performance. Fine particle separation is one of the main areas which still remain weak. This paper will present a new design of fine particle drum separators which used for particle size less than 3 mm. A big problem in processing of iron ore is the grade and recovery of mineral values in the fines fraction. The new design high efficiency drum separator is developed to handle fine feeds. In this drum separators both of the drum shell and magnetic yoke rotate in opposite direction. the results showed that when the material feed size was = 1298 μm, drum shell speed was 42.5 rev/min, magnetic yoke speed was 100 rev/min and the maximum intensity of magnetic field was at = 30° the feed grade increased from 50.87 to 65.67 in concentrate box, increase to 60.45 in middle box and tail grade was 24.44. The total achieved recovery for both concentrate and middle box was 81.89 per cent.

Nov 8, 2021

By L Kormos, V Lawson, G Hill, G Marrs

"In sulfide nickel deposits throughout the world, pentlandite and pyrrhotite are commonly found together along with varying amounts of chalcopyrite and platinum group minerals (PGMs). The mafic or ultramafic host silicates associated with the sulfide mineralisation commonly exhibit a complex assemblage of magnesium bearing silicates, many of which themselves contain significant nickel. Four types of ore are proposed, each presenting their own processing challenges. These are: economic grades of Ni, Cu and PGE (platinum group element) in a pyrrhotite-bearing sulfide deposit, with low pyrrhotite to pentlandite ratios  economic grades of Ni, Cu and PGE in a pyrrhotite-bearing sulfide deposit, with moderate to high pyrrhotite to pentlandite ratios uneconomic high pyrrhotite: low tenor deposits low-grade low sulfide, high MgO ± PGE deposits that can sometimes be economically mined and processed.The grades and recoveries of nickel concentrates produced from sulfide ores can be significantly impacted by the ore mineral texture, the nickel tenor of the sulfides, and the polytype of pyrrhotite which may be either hexagonal (non-magnetic) or monoclinic (magnetic). The mineralogy of the silicates is also of great importance, especially the magnesium silicates and those which tend to produce particles which are asbestiform or which affect slurry viscosity. Other magnesium silicates such as serpentine carry nickel in solid solution, limiting the recovery entitlement of nickel by flotation because serpentine is not amenable to sulfide flotation mechanisms. Differences in plant flow sheets and reagent assemblages are required to effectively separate these minerals.Experience from a variety of plant operations and from extensive flow sheet development programs are discussed. Examples are given of where significant improvements in nickel circuit performance can be made by adjusting plant physical processing conditions or process chemistry to compensate for measurable ore properties and characteristics.CITATION:Lawson, V, Hill, G, Kormos, L and Marrs, G, 2014. The separation of pentlandite from chalcopyrite, pyrrhotite and gangue in nickel projects throughout the world, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By S Taylor, B Lumsden, G Long

Statistical metallurgical plant trials are becoming more widespread, as a valuable tool for increasing plant profitability. Generally, a single parameter like metal recovery varies under the trial condition while all other variables such as average metal feed grade or average metal concentrate grade are equal for the two test conditions during the period of the test. Metal recovery is usually the measured variable because concentrate grade is fixed by smelter terms, and plants operate to maximise recovery at the required concentrate grade. However, in all flotation plants there is a relationship between concentrate grade and metal recovery, and under the same conditions increasing one results in a decrease in the other. At MMGÆs Rosebery Mine the zinc concentrate produced is generally above smelter specifications, so zinc concentrate grade can vary during a test. During trialling of magnetic conditioning in the Rosebery zinc circuit, the difference in both zinc recovery and zinc concentrate grade were analysed. The analysis of changes in zinc grade and recovery during the trial raised some interesting questions about the relationship between concentrate grade and recovery. A paired statistical method was developed and tested to combine in each pair the change in concentrate grade and recovery in a single result that could be analysed by a paired t test. This method was found to be very sensitive to combined, varying changes in concentrate grade and/or metal recovery. It was also evaluated on plant test results from another flotation plant to verify its applicability in other plants. CITATION:Long, G, Taylor, S and Lumsden, B, 2012. Statistical plant trials - Efficiently combining concentrate grade and metal recovery results, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By B J. Monaghan, R J. Longbottom, S Prabowo, D Del Puerto, B Maisuria, C W. Bumby

The use of hydrogen as a reducing agent can substantially reduce carbon dioxide (CO2) emissions from the ironmaking process. Iron ore fines can be reduced in a fluidised bed (FB) using hydrogen (H2) at high temperatures (>800°C), although several studies have reported the sticking of particles which causes the bed to defluidise, effectively shutting down the process. Here, we report results from the reduction of New Zealand (NZ) titanomagnetite (TTM) ironsands in a small-scale laboratory FB (100 g) at temperatures between 800–1000°C using H2 flow rates up to 5 standard L/min. No sticking phenomena are observed under any of these conditions, which is attributed to the formation of a stable titanium-bearing oxide layer on each particle’s exterior, preventing iron-iron contact at the particle surfaces. Pre-oxidised NZ TTM ironsands have also been studied and shown not to stick. Interestingly, at lower reaction temperatures the reduction kinetics for pre-oxidised ironsands is faster than for as-received ironsands. This increased kinetic rate can be attributed to the preoxidation stage inducing micro-fractures that create a void for the hydrogen to diffuse into the inner regions of the particle. In addition, oxidation of TTM appears to segregate the particle into two distinct phases, a high Aluminium-Magnesium (Al-Mg) phase and a high Titanium (Ti) phase. The findings are important as increasing the operating temperature of the FB reactor results in a faster reaction rate and higher gas utilisation, making the process more economically attractive. Furthermore, oxidation of NZ TTM ironsands results in a faster reduction rate at lower temperatures (800°C– 900°C) opening the opportunity to reduce the reaction temperature which might be beneficial in a final commercial-scale process.

Sep 18, 2023

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

By A Golsby

Gunite was invented in 1907 by Carl Akeley to repair a crumbling facade of the Field Columbian Museum in Chicago. The method used was to blow dry material out of a hose with compressed air and inject water at the nozzle as it was released. In 1911, he was granted a patent for his invention, the ‘cement gun’; the equipment used; and ‘gunite’, the material that was produced.The advantages of using the dry mix process is that the water content can be adjusted instantaneously, allowing more effective placement in overhead and vertical applications without using accelerators. The dry mix process is useful in repair applications when it is necessary to stop frequently as the dry material is easily discharged from the hose.This paper describes the applications and principles of the gunite pump system in underground coal mining and discusses why it is the preferred spraying system for both cement and plaster products.It also addresses improving productivity and examines dust, respirable crystalline silica (RCS) and health issues around gunite pump systems. The solutions include development of the latest componentry for current gunite pumps to improve their efficiency and allow their operation to be dustless.In particular, this paper addresses:why and where RCS is a problem in underground coal mininghow RCS hazards and its propagation can be managedhow the gunite pump system has become dustlesshow the gunite system has become more productivegunite occupational health and safety issues and how they have been solveda case study of gunite dry spraying.CITATION:Golsby, A, 2015. The development of a dustless dry gunite pump system in underground coal mining – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 41–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

This paper outlines the role of commissioning in the project cycle, shows how to get organised for commissioning and describes the principal commissioning activities. Emphasis is placed on appointing key commissioning staff early in the project to coordinate the preparations for commissioning and on detailed planning and tracking to ensure that the required commissioning activities are performed satisfactorily. The management of safety during commissioning is reviewed.

Jan 1, 2005

By Y K. Ji, B J. Chung

In recent years, the utilisation of ultra-fine ore in ironmaking has gradually increased due to the depletion of high-quality iron ore. The use of ultra-fine ore in the ironmaking process is typically energy intensive and leads to high CO2 emissions. The improvement of sinter reducibility is one of the methods used to reduce the environmental impact of using fine ore.In this study, a high-strength and high-reducibility sinter manufacturing process was investigated by controlling the sintering reaction. The key technology used in this method is the manufacture of mini-pellets by selective granulation equipment. The mini-pellets consist of iron ore, limestone and burnt lime and are designed to melt at temperatures below 1200°C. The molar ratio of CaO to Fe2O3 of the mini-pellets is 0.25~0.75. The 2~5 mm diameter mini-pellets are manufactured with burnt lime as the binding material.During the sintering of mini-pellets, goethite, which has relatively high reducibility, should be retained as residual ore in the sinter cake. The strength of the sinter cake was kept by the bonding reaction of the mini-pellets, which have a low melting temperature. This is the main principle of the reaction-controlled sintering method.The reaction-controlled sintering method manufactures a high-strength and high-reducibility sinter cake and increases sinter productivity by around 15 per cent using ultra-fine iron ore.CITATION:Chung, B J and Ji, Y K, 2015. Production of high-quality sinter by controlling the sintering reaction, in Proceedings Iron Ore 2015, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By A Hekmat, R Castro, A Casali, R Gómez

Block caving is the most economic underground methods for excavating massive orebodies, due to the high productivity and low production costs. The success of block caving operations depends on the fragmentation and draw control as large blocks decrease the equipment efficiency, inhibit the material flow and may lead to expensive secondary blasting. Even though ore handling system design, as well as overall economic results, both critically rely on secondary fragmentation, this parameter continues to be one of the least understood issues in the caving operations.This research focuses on the experimental study of secondary fragmentation, considering the impact of vertical pressures and material flow. Experiments using a load-haul-dump extraction system were conducted under laboratory conditions to quantify the influence of pressure and particle size on secondary fragmentation. Results demonstrate that increasing the vertical pressure (simulating deeper conditions) leads to higher fragmentation (smaller particle size) and greater fines generation during draw. The experimental results were applied to calibrate the developed mathematical model based on kinetic matrix. The acceptable accordance between the comminution model results and the reality showed that this method is convenient in predicting the secondary fragmentation in block caving.CITATION:Castro, R, Gómez, R, Casali, A and Hekmat, A, 2016. Experimental and comminution model framework for secondary fragmentation prediction in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J E. Everett

A block model of the orebody is used to plan a mine. The first requirement is to identify ore to be extracted, discarding waste, so as to meet target grade, generally in multiple analytes. Commonly, cut-off values are set for each analyte, so as to distinguish ore from waste. It will be shown that, if more than one analyte is important, this procedure is wasteful of ore and a composite cut-off function is preferable.A second requirement is to sequence the ore extraction so that the variability in ore grade is controlled: failure to do so will result either in low-quality ore being marketed, or excessive re-handling being required to blend the ore to reduce the grade variability.A third requirement is that the extraction sequence should be such as to control the amount of equipment movement required, enhancing the equipment productivity.The overall objective, to optimise the Net Present Value (NPV) of the mined ore, is simply stated but complex in realisation, since so many factors, such as target grade, grade variability, equipment choice, equipment movement, and downstream blending all have alternatives which can be traded off against each other, and all of which contribute to the costs and benefits making up the total NPV.There exist commercial packages for ore selection and mine planning. However, they are often of a ‘black box’ nature, and users are sometimes not fully aware of the criteria being applied. In particular, the treatment of quality as a multidimensional vector may be problematic. The purpose of this paper is to discuss some of the issues involved and to suggest an alternative set of approaches, which should complement existing commercial treatments.The discussion will be illustrated specifically by reference to the mining of iron ore, but the issues are relevant to a wide variety of mining situations

Sep 5, 2011

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023