Search Documents

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By J Harris, J Li, M Shi, P A. Kirsch, D Sprott

Australia has an enviable global reputation as a leader in health and safety outcomes in the hazardous industry of mining, in part due to an increased application of risk management regarding operational planning and mining practice. In 2010, the Australian Coal Association Research Program (ACARP) initiated a major project, RISKGATE, to build, capture and deliver a national body of knowledge to assist companies with the management of risk in coal mining. The online system contains information for tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives underground, explosives open cut, manual tasks, slips/trips/falls, outbursts, coal bumps and bursts, human–machine interface, tailings dams, occupational hygiene and inrush. In 2014, RISKGATE is developing content for fitness for work (fatigue, drugs, alcohol, physical well-being, psychosocial well-being).This paper analyses underground mining fatalities in Australia and the United States since 2002 and introduces RISKGATE with a focus on the knowledge base for management of hazards in underground operations. Through capturing coal industry expert operational knowledge, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover within the mining industry. This coal-based body of knowledge is a platform that can be evaluated and implemented for other mining domains and high-risk industries within the energy supply chain.CITATION:Kirsch, P A, Shi, M, Harris, J, Li, J and Sprott, D, 2014. RISKGATE and underground operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 11–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Kerr I. D, Kennedy M

Flash X-radiographs were obtained of commercial electric No 6 and No 8* strength aluminium tube detonators in small-diameter cartridges of emulsion explosive at various times after fusehead operation. The trigger system for the radiography was based on the detection of light following fusehead firing via optical fibres inserted into the fusehead cavity during detonator assembly. These experiments were simulated using a finite element hydrocode with realistic treatment of the non-ideal reaction kinetics. Excellent agreement was demonstrated for the shape and position of the shock waves. In both cases, initiation of the emulsion was predominantly forward from the detonator. For the No 8* strength detonator, this initiation resulted from the shockwave delivered through the sides of the detonator, while for the No 6 strength detonator, initiation was the result of a complex interaction between shockwaves originating both from the sides and from the endcap. In the reverse direction (towards the crimped end of the detonators), initiation was only weakly dependent on detonator strength, being controlled mainly by the competing processes of rarefaction from the cartridge boundaries and comer turning of the detonation wave from the forward initiation. The consequences for field performance of small-diameter emulsions will be discussed.

Jan 1, 1990

By K Fiedler, A Newell, P D. Munro

Test work is the foundation upon which the success of projects and subsequent operations is laid, reflected in Professor Arthur Taggart’s pithy observation: ‘Make your mistakes on the small scale and your profits on the larger scale’. Indeed, Professor AllanTrench has succinctly noted that ‘Get the metallurgical characteristics wrong and you don’t have a project’.With deposits becoming lower grade, more structurally and mineralogically complex, final products requiring lower levels of impurities and tailings management demanding more attention, test work now assumes even greater significance in the acceptance and successful execution of a project. This paper is the first in a series aiming to stimulate thought on the metallurgical test work process by getting back to the fundamental basics through exploring and providing some guidelines for the metallurgical testing world, noting preferred practices as well as precautions and mitigations. This covers the key characteristics of metallurgical test work programs, including what needs to be done, sample selection, quality control and associated drivers, and most importantly, selecting, assessing and managing test work facilities. CITATION:Newell, A, Munro, P D and Fiedler, K, 2018. Metallurgical test work – between a rock and a hard place, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 15–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T M. Brettell, D Sidea

The CSA Mine is located in Cobar, New South Wales and is operated by Glencore. Large scale underground production started from 1965, with zinc, lead, silver and copper extracted in the past. The current operations focus on copper, with a silver co-product.From 2014 to 2016, Cobar Management Pty Ltd (CMPL) undertook a major capital project to upgrade the primary ventilation system at the CSA Mine. This involved the development of ten raises using full-face raise boring from surface to a depth of 1450 m. The total length of the raises was approximately 2500 m. Geotechnical conditions were identified as a key project risk during the early planning stages of the project. Timely quantification of the geotechnical risks was required to minimise project delays and cost overruns. Geotechnical investigations were planned and conducted for each raise prior to pilot drilling and full-face back reaming.Nine of the ten raises had final wall camera and laser baseline surveys completed following full-face reaming. The surveys were conducted progressively, allowing ongoing back analysis and calibration of geotechnical evaluations as the project advanced.This paper presents the design and planning process of the raise bored excavations. It details the geotechnical investigation work undertaken to mitigate the geotechnical risks and the challenges and learnings from the project including the benefits of close collaboration between the parties involved.CITATION:Sidea, D and Brettell, T M, 2017. The CSA ventilation upgrade – geotechnical challenges and learnings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 341–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

By W. M. LONIE

Address by the President of the Institute (Mr W M Lonie) in making the presentation of the Certificate of Honorary Membership to Sir Ian McLellan, K.C.G.M, K.B.E. Address by Sir Ian McLellan after accepting the award.

Jan 1, 1979

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By C Zhang, I Canbulat, G Fan, D Zhang, C Wang

A clear understanding of the intensity of coal and rock burst is the basis for future research on burst mechanism and control. There has been a wide variety in the description of coal and rock burst damage at different countries using multi-methods, which makes the common understanding even more challenging. Therefore, this paper presents a broad review on the quantifications of intensity of coal and rock burst and seismic risk around the world, considering critical factors including seismic energy, magnitude, peak particle velocity and ejection velocity. It is found that the seismic energy of coal and rock burst can widely range from 0.002 MJ to 60000 MJ, with equivalent Richter magnitude from -1 to 4. The daily seismic energies can be used for seismic risk potential assessment, with energy levels from 0.1 KJ to 10 MJ, which is much lower than the burst sources. The magnitude of the seismic events can be also estimated based on the weight of damaged coal mass and human senses of vibration and sound. For the seismic intensity represented by peak particle velocity (ppv), it keeps constant within fault radius and attenuates with a speed of 1/r4 and 1/r in near and far field respectively, thus it is possible for a small seismic event to induce considerable ppv causing severe damage if the epicentral distance is small enough. There has not been a strong correlation between the ejection velocity and ppv, as seismic energy is only one of the energy sources that contribute to the kinetic energy of burst damage. CITATION:Wang, C, Zhang, C, Canbulat, I, Zhang, D and Fan, G, 2018. Intensity quantification of coal and rock burst risk – a review, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 223–233 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By V A. Diemar

The Chatree Gold Project represents a greenfields discovery of metallurgically clean shallow gold mineralisation in a logistically simple terrain. Total Measured, Indicated and Inferred Resources are currently 31 tonnes of gold and 160 tonnes of silver. Gold occurs in an adularia-sericite epithermal system within quartz-calcite-adularia veins, breccias and stockworks. Host rocks are volcanic arc porphyritic latite-trachyte flows, their pyroclastic equivalents and volcaniclastics of upper Permian to upper Triassic age. The mineralisation was deposited in dilated zones during repeated reactivation of pre-existing structures. To-date five mineralised prospects have been defined by drilling with three reaching JORC Code Mineral Resources status. The project is in its definitive feasibility stage and is anticipated to be in construction during 2000.

Jan 1, 1999

By V Gau, L Overmeyer, M Kesting

Economically efficient mining processes can be significantly assisted by the implementation of sensor technologies for the detection of materials and boundary layers between materials inside the stratum. These sensors are meant to facilitate the machinery operator and illustrate furthermore the prerequisites in assisting tools towards fully automated mining equipment. Therefore, project æSensory Identification of Material Type and Detection of the InterfacesÆ (SIMT) aims at the integration of ground penetrating radar (GPR) and geoelectric sensor technology by endowing with them a bucket of a bucket wheel excavator. For this reason, a sensor bucket was developed and tested in the Inden Mine of RWE Power AG. The feasibility of integration and deployment of such sensor technology has been proven effective for the conditions of open cast mining. The main focus of current research lies on developing algorithms to analyse the acquired measurement data from the sensors to automatically detect layers and materials. A computer network receives the GPR and geoelectric measurement data as well as the positioning data of the sensor bucket. The positioning data mainly consists of GPS and encoder information, which is merged with the sensor data by using the UTC time stamp. With the aid of consecutive processes the relevant information will be extracted and provided to the user. The aim of SIMT is to replace material identification, traditionally carried out by the operator, by implementing a continuous operating interpretation system in mining equipment based on GPR and geoelectric sensor technology, resulting in more detailed information regarding the working face during an excavation. This detailed information provides an opportunity for efficient planning and controlling of selective mining of natural deposits, such as the process of lignite mining.

Sep 26, 2011

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By H Sichani-Teimouri, B N. Noller, J C. Ng, R N. Alsaadi, P L. Breuer, S Shini

Cyanide has been used for over a century worldwide for gold extraction. However, the presence of several metals and metalloids in ore requires greater amount of cyanide for an efficient gold recovery due to their solubilisation in conjunction with gold. The extraction residues are discharged into tailing storage facilities (TSFs) and may cause bird mortality if there is exposure to cyanide-bearing wastewater exceeding the toxic threshold. The toxicity arises from free cyanide released from weak acid dissociable (WAD) cyanide complexes. The International Cyanide Management Code (ICMC) has deemed 50 mg/L of WAD cyanide released into TSFs to be safe for wildlife protection. However, this concentration is based on observations of an apparent lack of toxicity rather than a toxicological approach. The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) identified in 2010 that there is a lack of toxicity data to properly assess the environmental significance of cyanide levels at gold mines. Lack of knowledge for the toxicity of free cyanide and metal cyanide complexes to wildlife led to consider alternative direct assessment techniques for designating safe levels. Whilst toxicity may be assessed by using young chickens with animal ethics approval, the traditional bioassay approach to assess cyanide toxicity is impractical for gold mine TSFs. Bioassays using algal species such as Euglena gracilis, a unicellular alga, are widely used for ecotoxicological studies. A unique feature is that the Euglena gracilis Z cell has plant-like while SMZ cell has animal-like characteristics. The aims of this project are to evaluate the suitability of Euglena gracilis Z and SMZ strains to assess the toxicity of free cyanide and both strong (cobalt) and weak (zinc, copper and nickel) acid dissociable metal-cyanide complexes that may be present in TSFs.CITATION:Noller, B N, Ng, J C, Shini, S, Breuer, P L, Sichani-Teimouri, H and Alsaadi, R N, 2014. Development of a toxicity approach to evaluate free cyanide and metal cyanide complexes in waters associated with gold and other mining, in Proceedings Life-of-Mine 2014 , pp 573–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004